{"product_id":"epdm-b-fender-with-stainless-steel-strip-22mm-x-14mm-18m-roll","title":"EPDM B Fender with Stainless Steel Strip – 22mm x 14mm – 18m Length","description":"\u003cp\u003eA slim EPDM rubber B fender, 22 mm wide and 14 mm high, supplied with a 304 stainless steel retaining strip already in its slot. You screw through the strip, so the fender goes on in a straight line with even clamping, and the screw heads sit below the two rounded lobes where nothing can catch on them. It comes as one continuous 18 m length: enough to run both sides of a small dinghy, or a long wall, without joins.\u003c\/p\u003e\n\n\u003ch3\u003eAt a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 22 mm wide × 14 mm high, the smallest B fender profile we stock\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixing strip included:\u003c\/strong\u003e 8 mm wide × 0.76 mm (22 gauge) 304 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e black EPDM, 70° Shore A, rated for UV, ozone and outdoor use\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 18 m continuous, about 0.39 kg per metre (about 7 kg in total)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrice per metre:\u003c\/strong\u003e about £24.17 inc VAT (£435.00 ÷ 18 m)\u003c\/li\u003e\n\u003cli\u003eIn stock for same-day dispatch\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhere it is used\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRubbing strake on dinghies, tenders, rowing boats and small workboats\u003c\/li\u003e\n\u003cli\u003eEdge protection on pontoons, jetties and boarding platforms where a big fender would get in the way\u003c\/li\u003e\n\u003cli\u003eBump strip on van, truck and ambulance bodywork, tail lifts and load-bed edges\u003c\/li\u003e\n\u003cli\u003eWall, door-frame and corner protection in factories, loading bays, car parks and corridors\u003c\/li\u003e\n\u003cli\u003eShopfitting and display edges that need a neat, low bumper\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eTechnical drawing\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-b-fender-stainless-strip-22x14-technical-drawing.png?v=1795316724\" alt=\"Technical drawing of the EPDM B fender 22 x 14 mm cross-section with the 8 x 0.76 mm stainless steel strip, dimensions in mm\" width=\"2000\" height=\"1490\" loading=\"lazy\" style=\"max-width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eOverall width, height and strip size are manufacturer values. Lobe radius, slot width and cavity depth follow the manufacturer's section for illustration and are not specified dimensions.\u003c\/small\u003e\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003cth\u003eTest method \/ note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eProfile\u003c\/td\u003e\n\u003ctd\u003eB fender: flat back, twin rounded lobes, open T-slot\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall width\u003c\/td\u003e\n\u003ctd\u003e22 mm\u003c\/td\u003e\n\u003ctd\u003eNominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall height (projection from surface)\u003c\/td\u003e\n\u003ctd\u003e14 mm\u003c\/td\u003e\n\u003ctd\u003eNominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRetaining strip width\u003c\/td\u003e\n\u003ctd\u003e8 mm\u003c\/td\u003e\n\u003ctd\u003eNominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRetaining strip thickness\u003c\/td\u003e\n\u003ctd\u003e0.76 mm (22 gauge)\u003c\/td\u003e\n\u003ctd\u003eNominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRetaining strip material\u003c\/td\u003e\n\u003ctd\u003e304 stainless steel\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFender material\u003c\/td\u003e\n\u003ctd\u003eEPDM (ethylene propylene diene monomer)\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eColour\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLength supplied\u003c\/td\u003e\n\u003ctd\u003e18 m, one continuous piece\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.39 kg\/m (about 7.0 kg per 18 m)\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness\u003c\/td\u003e\n\u003ctd\u003e70° Shore A\u003c\/td\u003e\n\u003ctd\u003eISO 7619-1 \/ DIN 53505 \/ ASTM D2240\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile strength\u003c\/td\u003e\n\u003ctd\u003e7.2 MPa\u003c\/td\u003e\n\u003ctd\u003eISO 37 \/ DIN 53504 \/ ASTM D412\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElongation at break\u003c\/td\u003e\n\u003ctd\u003e305 %\u003c\/td\u003e\n\u003ctd\u003eISO 37 \/ DIN 53504 \/ ASTM D412\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTear strength\u003c\/td\u003e\n\u003ctd\u003e55 N\/mm\u003c\/td\u003e\n\u003ctd\u003eISO 34-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompression set\u003c\/td\u003e\n\u003ctd\u003e23 % (24 h at 100 °C, 25 % deflection)\u003c\/td\u003e\n\u003ctd\u003eISO 815\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDensity\u003c\/td\u003e\n\u003ctd\u003e1.28 g\/cm³\u003c\/td\u003e\n\u003ctd\u003eISO 2781 \/ DIN 53479 \/ ASTM D297\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRebound resilience\u003c\/td\u003e\n\u003ctd\u003e23 %\u003c\/td\u003e\n\u003ctd\u003eDIN 53512 \/ ASTM D1054\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOzone resistance\u003c\/td\u003e\n\u003ctd\u003eNo cracking (72 h at 40 °C, 50 pphm)\u003c\/td\u003e\n\u003ctd\u003eISO 1431-1 method A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eService temperature\u003c\/td\u003e\n\u003ctd\u003eAbout -40 °C to +120 °C\u003c\/td\u003e\n\u003ctd\u003eTypical for EPDM, not tested on this profile\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensional tolerance\u003c\/td\u003e\n\u003ctd\u003eNot stated by the manufacturer\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need a tolerance for a critical fit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eMaterials and compliance\u003c\/h3\u003e\n\u003cp\u003eThe fender is EPDM rubber and the retaining strip is 304 stainless steel. EPDM is chosen for outdoor and marine use because it holds up to sunlight, ozone, rain and salt air without cracking; the ozone result above is the manufacturer's test on this compound. The manufacturer is ISO 9001:2015 registered. No product approvals (for example FDA, WRAS, REACH or RoHS) are stated for this item, so we do not claim any. If you need a declaration for your project, contact us before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eHow it fits\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-b-fender-22x14-how-it-fits.png?v=1795316723\" alt=\"Fitting guide for the 22 x 14 mm B fender showing a screw through the stainless strip into a timber gunwale at about 300 mm centres\" width=\"2000\" height=\"1490\" loading=\"lazy\" style=\"max-width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eMeasure the run and add a little for trimming. Cut the rubber with a sharp knife and the steel strip with a hacksaw or snips, then file the cut end smooth.\u003c\/li\u003e\n\u003cli\u003eHold the fender straight with the flat back against the surface and the slot facing out.\u003c\/li\u003e\n\u003cli\u003eDrill through the strip and into the surface at about 300 mm centres, starting about 50 mm in from each end.\u003c\/li\u003e\n\u003cli\u003eFix with countersunk stainless screws (A4 marine grade on boats; plugs or anchors on masonry). The head must pass through the slot opening, so check your screws against the fender before buying a box. Do not over-tighten.\u003c\/li\u003e\n\u003cli\u003eOn boats, bed each screw hole in marine sealant.\u003c\/li\u003e\n\u003c\/ol\u003e\n\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eAdd up every edge you want to protect and allow about 5 % for trimming. A 4.5 m dinghy needs roughly 9.5 m to run down both sides, so one 18 m length covers it with spare. A 15 m wall run fits on one length; 30 m needs two.\u003c\/p\u003e\n\n\u003ch3\u003eWhich size do I need?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProfile\u003c\/th\u003e\n\u003cth\u003eChoose it when\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e22 × 14 mm with steel strip (this one)\u003c\/td\u003e\n\u003ctd\u003eYou want a slim fender that screws on straight, with hidden screw heads\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-rubber-b-fender-profile-22mm-x-14mm-solid-black-36m-roll\"\u003e22 × 14 mm plain, 36 m\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eSame profile without the strip, for adhesive fixing or longer runs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-rubber-b-fender-32mm-x-16mm-with-stainless-steel-strip-15m-coil\"\u003e32 × 16 mm with steel strip\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eYou want a little more rubber between the knock and the surface\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-rubber-b-fender-with-stainless-steel-strip-44mm-x-19mm-15m-roll\"\u003e44 × 19 mm with steel strip\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eHeavier boats, loading bays and harder impacts\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs the stainless steel strip included?\u003c\/strong\u003e\u003cbr\u003eYes. The 8 mm × 0.76 mm 304 stainless strip comes in the slot along the full 18 m. You only need to buy screws.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I fix it?\u003c\/strong\u003e\u003cbr\u003eDrill through the strip at about 300 mm centres and screw into the surface with countersunk stainless screws. The screw heads sit down in the slot, below the rubber lobes, so they are protected and do not scratch anything that rubs along the fender.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich way round does it go?\u003c\/strong\u003e\u003cbr\u003eThe flat back goes against the boat, wall or panel. The two rounded lobes and the slot face outwards.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs 22 × 14 mm big enough for my boat?\u003c\/strong\u003e\u003cbr\u003eIt suits dinghies, tenders and small craft, and any edge where a slim profile matters. It stands 14 mm proud of the surface. For heavier boats or harder knocks choose the 32 × 16 mm or 44 × 19 mm B fender.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan it be used outdoors and in salt water?\u003c\/strong\u003e\u003cbr\u003eYes. EPDM resists UV, ozone, rain and salt air, and the manufacturer's ozone test shows no cracking. The strip is 304 stainless steel. For constant immersion in seawater, rinse it with fresh water from time to time.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat temperature can it take?\u003c\/strong\u003e\u003cbr\u003eEPDM is typically used from about -40 °C to +120 °C. That is a typical figure for the material; the manufacturer has not published a temperature test for this profile.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I cut and join it?\u003c\/strong\u003e\u003cbr\u003eCut the rubber with a sharp knife and the strip with a hacksaw or tin snips, then file off any burr. Butt two lengths tightly together and put a fixing about 50 mm either side of the joint. Around tight corners, cut a small V-notch in the back of the rubber and the strip so it bends without kinking.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it go round a curved hull?\u003c\/strong\u003e\u003cbr\u003eYes, it bends easily round the gentle curves of a gunwale. Fixings every 300 mm, or closer on tight curves, hold it to the shape.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I buy a shorter length?\u003c\/strong\u003e\u003cbr\u003eThis item is one continuous 18 m length. Contact us if you need a different length or a quantity for a fleet.\u003c\/p\u003e\n\n\u003cp\u003eQuestions about sizing or fixing? Call \u003ca href=\"tel:+441282277786\"\u003e+44 1282 277786\u003c\/a\u003e or email \u003ca href=\"mailto:sales@industrial-polymers.co.uk\"\u003esales@industrial-polymers.co.uk\u003c\/a\u003e.\u003c\/p\u003e","brand":"Industrial Polymers","offers":[{"title":"Default Title","offer_id":56591890350459,"sku":"IP-BFSS-22X14-18M","price":435.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-b-fender-with-stainless-steel-strip-22mm-x-14mm-18m-rol-studio.jpg?v=1795106239","url":"https:\/\/industrial-polymers.co.uk\/products\/epdm-b-fender-with-stainless-steel-strip-22mm-x-14mm-18m-roll","provider":"Industrial-polymers ","version":"1.0","type":"link"}