{"product_id":"epdm-sponge-crown-strip-14-5mm-x-7-5mm-50m-coil","title":"EPDM Sponge Crown Strip – 14.5mm x 7.5mm, Self-Adhesive – 50m Coil","description":"\u003cp\u003e\u003cstrong\u003eThe tallest crown strip in the range: black EPDM sponge, 14.5 mm wide and 7.5 mm high, with a peel-and-stick adhesive base. One continuous 50 m coil.\u003c\/strong\u003e Five rounded crowns press flat when a hatch, door or lid closes on them, giving five sealing lines across the face, while the extra height soaks up knocks and copes with uneven or wider gaps than the low-profile strips.\u003c\/p\u003e \u003ch3\u003eAt a glance\u003c\/h3\u003e \u003cul\u003e \u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 14.5 mm wide × 7.5 mm high; 6.5 mm at the groove floor (1 mm deep grooves)\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eFace:\u003c\/strong\u003e five crowns and four scalloped grooves for multiple sealing lines\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eFixing:\u003c\/strong\u003e factory-applied adhesive backing with a peel-off liner; sticks to clean metal, plastic, wood and rubber\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e skinned, solid expanded (sponge) EPDM, very soft at 40° Shore OO, non-marking\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eOutdoors:\u003c\/strong\u003e rated excellent for ozone, weather and UV; flexible at -40 °C\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eCoil:\u003c\/strong\u003e 50 m continuous length, black, 40 g\/m, about £4.71 per metre\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eStock:\u003c\/strong\u003e held in stock in the UK and dispatched from stock\u003c\/li\u003e \u003c\/ul\u003e \u003ch3\u003eTypical uses\u003c\/h3\u003e \u003cul\u003e \u003cli\u003eWeather and dust seals on hatches, access panels, vehicle and trailer doors, and boat lockers\u003c\/li\u003e \u003cli\u003eLid seals on equipment cases, enclosures and cabinets with a 5 to 6 mm closed gap\u003c\/li\u003e \u003cli\u003eClosure and glazing seals where the mating face is uneven\u003c\/li\u003e \u003cli\u003eShock-absorbing bump strip on tailgates, drop-down sides, shelving and machinery guards\u003c\/li\u003e \u003cli\u003eExpansion-joint and anti-vibration packing between panels and frames\u003c\/li\u003e \u003c\/ul\u003e \u003ch3\u003eTechnical drawing\u003c\/h3\u003e \u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-crown-strip-14-5mm-x-7-5mm-technical-drawing.png?v=1795310519\" alt=\"Technical drawing of the EPDM sponge crown strip: 14.5 mm wide, 7.5 mm high, 6.5 mm at the groove floor, five crowns, adhesive-backed base\" width=\"2000\" height=\"1490\" loading=\"lazy\" style=\"width:100%;height:auto\"\u003e\u003c\/p\u003e \u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e \u003cthead\u003e\u003ctr\u003e\n\u003cth scope=\"col\"\u003eProperty\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eValue\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eTest method \/ basis\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e \u003ctbody\u003e \u003ctr\u003e\n\u003ctd\u003eProfile type\u003c\/td\u003e\n\u003ctd\u003eSolid crown strip: five rounded crowns separated by four scalloped grooves, on a flat self-adhesive base\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eOverall width (across the base)\u003c\/td\u003e\n\u003ctd\u003e14.5 mm\u003c\/td\u003e\n\u003ctd\u003eNominal; tolerance BS 3734 Class E3\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eOverall height (base to top of crowns)\u003c\/td\u003e\n\u003ctd\u003e7.5 mm\u003c\/td\u003e\n\u003ctd\u003eNominal; tolerance BS 3734 Class E3\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eHeight at the groove floor\u003c\/td\u003e\n\u003ctd\u003e6.5 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eGroove depth\u003c\/td\u003e\n\u003ctd\u003e1.0 mm (7.5 mm less 6.5 mm)\u003c\/td\u003e\n\u003ctd\u003eDerived from the manufacturer's dimensions\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eCrowns \/ grooves across the face\u003c\/td\u003e\n\u003ctd\u003e5 crowns, 4 grooves; spacing not dimensioned (about 3.4 mm pitch on the maker's drawing)\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing (shape only)\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eMinimum landing width\u003c\/td\u003e\n\u003ctd\u003e14.5 mm flat surface to stick to\u003c\/td\u003e\n\u003ctd\u003eEqual to the base width\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eFixing\u003c\/td\u003e\n\u003ctd\u003eFactory-applied adhesive backing with peel-off liner\u003c\/td\u003e\n\u003ctd\u003eAdhesive type and thickness not stated by the manufacturer\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eMaterial\u003c\/td\u003e\n\u003ctd\u003eExpanded (sponge) EPDM, skinned surface\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eColour\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eHardness\u003c\/td\u003e\n\u003ctd\u003e40° Shore OO\u003c\/td\u003e\n\u003ctd\u003eShore OO durometer scale (for soft foams); test standard not stated\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eDensity\u003c\/td\u003e\n\u003ctd\u003e0.5 to 0.9 g\/cm³\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e40 g per metre (about 2.0 kg per 50 m coil)\u003c\/td\u003e\n\u003ctd\u003eManufacturer figure (product page and datasheet agree)\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eWater absorption\u003c\/td\u003e\n\u003ctd\u003e5% maximum\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eCompression set\u003c\/td\u003e\n\u003ctd\u003e25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h)\u003c\/td\u003e\n\u003ctd\u003eManufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eHeat ageing\u003c\/td\u003e\n\u003ctd\u003e±30% change after 7 days at 70 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; property measured not stated\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eLow-temperature flexibility\u003c\/td\u003e\n\u003ctd\u003ePass at -40 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eOzone resistance\u003c\/td\u003e\n\u003ctd\u003eExcellent\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eWeather resistance\u003c\/td\u003e\n\u003ctd\u003eExcellent\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eUV light resistance\u003c\/td\u003e\n\u003ctd\u003eExcellent\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eMould growth resistance\u003c\/td\u003e\n\u003ctd\u003eVery good\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eService temperature range\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile)\u003c\/td\u003e\n\u003ctd\u003eTested points stated: flexible at -40 °C, aged at +70 °C\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eTensile strength, elongation at break, tear strength\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need them\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eDimensional tolerance\u003c\/td\u003e\n\u003ctd\u003eBS 3734 Class E3 (extruded sponge); sizes are approximate because the section is flexible\u003c\/td\u003e\n\u003ctd\u003eBS 3734\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003eSupplied length\u003c\/td\u003e\n\u003ctd\u003e50 m continuous coil\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003ePrice per metre\u003c\/td\u003e\n\u003ctd\u003eAbout £4.71\/m inc VAT (£235.41 per 50 m coil)\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e \u003c\/tbody\u003e \u003c\/table\u003e \u003cp\u003e\u003csmall\u003eThe manufacturer gives two compression-set figures for this part (25% maximum on the datasheet, 50% on the product page); both are shown above. Sponge sections are flexible, so treat all sizes as nominal.\u003c\/small\u003e\u003c\/p\u003e \u003ch3\u003eMaterials and compliance\u003c\/h3\u003e \u003cp\u003eSkinned expanded (sponge) EPDM with a factory-applied adhesive backing. The manufacturer describes the profile as non-marking, air and watertight, and resistant to ozone, weather, heat, steam, ketones and dilute acids and alkalis, with good electrical insulation. Like all EPDM it is not suited to oils, fuels or solvents.\u003c\/p\u003e \u003cp\u003eThe manufacturer does \u003cstrong\u003enot\u003c\/strong\u003e state any food-contact (FDA, EC 1935\/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.\u003c\/p\u003e \u003ch3\u003eHow it fits\u003c\/h3\u003e \u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-crown-strip-14-5mm-x-7-5mm-fitted-hatch-seal.png?v=1795310519\" alt=\"Illustration of the 14.5 x 7.5 mm crown strip stuck to a frame and squeezed to 5.5 mm by a closed hatch, with the free shape shown dashed\" width=\"2000\" height=\"2000\" loading=\"lazy\" style=\"width:100%;max-width:640px;height:auto\"\u003e\u003c\/p\u003e \u003col\u003e \u003cli\u003e\n\u003cstrong\u003eMeasure the closed gap.\u003c\/strong\u003e It should be smaller than 7.5 mm so the crowns are squeezed. About 5 to 6 mm (20 to 33% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eCheck the landing.\u003c\/strong\u003e The flat face you stick to should be at least 14.5 mm wide.\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eClean and dry.\u003c\/strong\u003e Wipe with isopropyl alcohol and let it dry. Fit above about 10 °C for the best bond.\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003ePeel and press.\u003c\/strong\u003e Peel the liner a short way at a time and press the base down firmly along its length. Do not stretch the strip or it will shrink back.\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eCorners and joins.\u003c\/strong\u003e Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.\u003c\/li\u003e \u003c\/ol\u003e \u003ch3\u003eWhich size do I need?\u003c\/h3\u003e \u003ctable\u003e \u003cthead\u003e\u003ctr\u003e\n\u003cth scope=\"col\"\u003eProfile\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSize (W × H)\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eBest for a closed gap of\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSupplied as\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e \u003ctbody\u003e \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-crown-strip-10mm-x-5mm-100m-coil\"\u003eEPDM sponge crown strip\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e10 × 5 mm\u003c\/td\u003e\n\u003ctd\u003eabout 3 to 4 mm\u003c\/td\u003e\n\u003ctd\u003e100 m coil, self-adhesive\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-crown-strip-15mm-x-4mm-adhesive-backed-100m-coil\"\u003eEPDM sponge crown strip\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e15 × 4 mm\u003c\/td\u003e\n\u003ctd\u003eabout 2.5 to 3 mm\u003c\/td\u003e\n\u003ctd\u003e100 m coil, self-adhesive\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEPDM sponge crown strip (this item)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003e14.5 × 7.5 mm\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eabout 5 to 6 mm\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003e50 m coil, self-adhesive\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-d-section-12mm-x-10mm-75m-coil\"\u003eEPDM sponge D section (hollow)\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e12 × 10 mm\u003c\/td\u003e\n\u003ctd\u003elarger gaps, lower closing force\u003c\/td\u003e\n\u003ctd\u003e75 m coil\u003c\/td\u003e\n\u003c\/tr\u003e \u003c\/tbody\u003e \u003c\/table\u003e \u003cp\u003e\u003csmall\u003eGap ranges are our guidance for 20 to 35% squeeze, not manufacturer figures.\u003c\/small\u003e\u003c\/p\u003e \u003ch3\u003eData sheet\u003c\/h3\u003e \u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-crown-strip-14-5mm-x-7-5mm-data-sheet-v2.pdf?v=1795310720\" target=\"_blank\" rel=\"noopener\"\u003eDownload the technical data sheet (PDF): drawing, full specification and compliance\u003c\/a\u003e\u003c\/p\u003e \u003ch3\u003eQuestions\u003c\/h3\u003e \u003cp\u003e\u003cstrong\u003eIs the price per metre or per coil?\u003c\/strong\u003e\u003cbr\u003ePer coil. One unit is a complete 50 m continuous coil, which works out at about £4.71 per metre.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eWhat gap will it seal?\u003c\/strong\u003e\u003cbr\u003eClosed gaps below its 7.5 mm height; aim for about 5 to 6 mm. For gaps of 3 to 4 mm the 10 × 5 mm crown strip is a better fit.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eHow do I fit it?\u003c\/strong\u003e\u003cbr\u003eClean the surface with isopropyl alcohol, peel back the liner a little at a time and press the flat base down firmly onto a landing at least 14.5 mm wide. Do not stretch it as you go.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eHow do I cut and join it?\u003c\/strong\u003e\u003cbr\u003eA sharp craft knife or scissors gives a clean square end. Butt the ends tightly together; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eCan I use it outdoors?\u003c\/strong\u003e\u003cbr\u003eYes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eWhat temperatures can it take?\u003c\/strong\u003e\u003cbr\u003eThe manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eWhy five crowns rather than a flat strip?\u003c\/strong\u003e\u003cbr\u003eEach crown makes its own line of contact, so the strip seals with less closing force than a flat foam block of the same size, and the grooves give the sponge room to spread as it is squeezed.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eCan I use it as a bump or impact strip?\u003c\/strong\u003e\u003cbr\u003eYes. At 7.5 mm it is the tallest crown strip we stock, and the soft 40° Shore OO sponge cushions knocks on tailgates, guards and shelving edges.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eWill it mark painted surfaces?\u003c\/strong\u003e\u003cbr\u003eThe manufacturer states it is non-marking.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eWill it stand up to oil or fuel?\u003c\/strong\u003e\u003cbr\u003eNo. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eIs it food-safe or WRAS approved?\u003c\/strong\u003e\u003cbr\u003eNo approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.\u003c\/p\u003e \u003ch3\u003eDelivery and help\u003c\/h3\u003e \u003cp\u003eHeld in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.\u003c\/p\u003e","brand":"Industrial Polymers","offers":[{"title":"50 m coil","offer_id":56590320435579,"sku":"IP-EPDMC-14.5X7.5-STD","price":235.41,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-crown-strip-14-5mm-x-7-5mm-black.png?v=1795310520","url":"https:\/\/industrial-polymers.co.uk\/products\/epdm-sponge-crown-strip-14-5mm-x-7-5mm-50m-coil","provider":"Industrial-polymers ","version":"1.0","type":"link"}