{"product_id":"epdm-sponge-door-seal-15mm-x-18mm-cut-lengths","title":"EPDM Sponge Door Seal – 15mm x 18mm, Dual Hardness, Self-Adhesive – 10m to 39m or 40m Coil","description":"\u003cp\u003e\u003cstrong\u003eA big, soft door seal for larger gaps: a hollow 15 mm sponge EPDM bead standing 18 mm tall on a firm, solid EPDM foot with self-adhesive tape. Cut to one continuous length from 10 m to 39 m, or a full 40 m coil.\u003c\/strong\u003e Peel the liner, press the 13.5 mm foot onto the frame, and the round bead squashes flat as the door closes. The dual-hardness build matters: the solid foot keeps the bead standing upright and stuck down, while the soft sponge tube takes up wide and uneven gaps that a thin strip cannot reach.\u003c\/p\u003e\n\u003ch3\u003eAt a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e Ø15 mm hollow bead, 18 mm overall height, 13.5 mm wide foot (sold as \"15 × 18 mm\")\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction:\u003c\/strong\u003e dual hardness: solid EPDM foot (70° Shore A) with an expanded EPDM sponge bead (40° Shore OO)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixing:\u003c\/strong\u003e self-adhesive tape on the underside of the foot, so no glue, clips or screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeals gaps:\u003c\/strong\u003e best on closed gaps of about 10 to 14 mm (our guidance)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutdoors:\u003c\/strong\u003e ozone, weather and UV resistance rated excellent; flexible at -40 °C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e one continuous length, 10 m to 39 m at £22.23 per metre, or a full 40 m coil for £687.06 (£17.18 per metre), all inc VAT\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStock:\u003c\/strong\u003e held in stock in the UK and dispatched from stock\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTypical uses\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDoor and tailgate aperture seals on vans, horseboxes, trailers, buses and classic vehicles\u003c\/li\u003e\n\u003cli\u003eWeather seals on shed, workshop, garage side and garden-room doors with a wide or uneven gap\u003c\/li\u003e\n\u003cli\u003eHatch, locker and lid seals on boats, kiosks, plant rooms and machinery covers\u003c\/li\u003e\n\u003cli\u003eLarge-gap seals on electrical enclosures, cabinets and acoustic or dust doors\u003c\/li\u003e\n\u003cli\u003eGlazing and closure seals where a soft, deep-compressing bulb is needed\u003c\/li\u003e\n\u003cli\u003eSoft buffer and anti-rattle strip on panels and doors that close onto a stop\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical drawing\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-door-seal-15mm-x-18mm-technical-drawing.png?v=1795310993\" alt=\"Technical drawing of the 15 x 18 mm EPDM sponge door seal: 15 mm hollow sponge bead, 18 mm overall height, 13.5 mm by 2.5 mm solid EPDM foot with 6 mm neck and adhesive tape\" width=\"2000\" height=\"1490\" loading=\"lazy\" style=\"width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth scope=\"col\"\u003eProperty\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eValue\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eTest method \/ basis\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eProfile type\u003c\/td\u003e\n\u003ctd\u003eHollow round sponge bead on a solid T-shaped foot, self-adhesive underside\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall height (base to crown)\u003c\/td\u003e\n\u003ctd\u003e18.0 mm\u003c\/td\u003e\n\u003ctd\u003eNominal; tolerance BS 3734 Class E3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBead outside diameter\u003c\/td\u003e\n\u003ctd\u003eØ15.0 mm (the widest point of the profile)\u003c\/td\u003e\n\u003ctd\u003eNominal; tolerance BS 3734 Class E3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBead bore\u003c\/td\u003e\n\u003ctd\u003eAbout Ø10.4 mm, giving a sponge wall of about 2.3 mm\u003c\/td\u003e\n\u003ctd\u003eScaled from the manufacturer's drawing; not separately stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFoot (base) width\u003c\/td\u003e\n\u003ctd\u003e13.5 mm on the drawing; 14 mm in the written specification\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing and product page\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFoot thickness\u003c\/td\u003e\n\u003ctd\u003e2.5 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNeck width (foot to bead)\u003c\/td\u003e\n\u003ctd\u003e6.0 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer's profile drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFixing\u003c\/td\u003e\n\u003ctd\u003eSelf-adhesive tape on the underside of the foot\u003c\/td\u003e\n\u003ctd\u003eManufacturer product page and drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaterial\u003c\/td\u003e\n\u003ctd\u003eDual hardness EPDM: solid EPDM foot, expanded (sponge) EPDM bead\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eColour\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness, solid foot\u003c\/td\u003e\n\u003ctd\u003e70° Shore A (page); 65 to 75 IRHD (datasheet)\u003c\/td\u003e\n\u003ctd\u003eShore A \/ IRHD; test standard not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness, sponge bead\u003c\/td\u003e\n\u003ctd\u003e40° Shore OO\u003c\/td\u003e\n\u003ctd\u003eShore OO scale for soft foams; test standard not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSponge density\u003c\/td\u003e\n\u003ctd\u003e0.5 to 0.9 g\/cm³\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.10 kg per metre (datasheet); 110 g per metre (product page). About 4.4 kg per 40 m coil\u003c\/td\u003e\n\u003ctd\u003eManufacturer figures\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile strength, solid foot\u003c\/td\u003e\n\u003ctd\u003e10 MPa\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElongation at break, solid foot\u003c\/td\u003e\n\u003ctd\u003e500%\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTear strength, solid foot\u003c\/td\u003e\n\u003ctd\u003e50 kN\/m\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompression set, solid foot\u003c\/td\u003e\n\u003ctd\u003e21% after 22 hours at 70 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompression set, sponge bead\u003c\/td\u003e\n\u003ctd\u003e25% maximum (24 h recovery) on the datasheet; 50% (22 h) on the product page\u003c\/td\u003e\n\u003ctd\u003eManufacturer figures differ; temperature and standard not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeat ageing, solid foot (70 h at 70 °C)\u003c\/td\u003e\n\u003ctd\u003eHardness change 0 IRHD; tensile change +9%; elongation change 0\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeat ageing, sponge (7 days at 70 °C)\u003c\/td\u003e\n\u003ctd\u003e±30% change\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; property measured not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOzone resistance\u003c\/td\u003e\n\u003ctd\u003eSolid foot: no cracks after 72 h at 40 °C, 22 pphm, extended. Sponge: rated excellent\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeather and UV resistance\u003c\/td\u003e\n\u003ctd\u003eExcellent\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMould growth resistance\u003c\/td\u003e\n\u003ctd\u003eVery good\u003c\/td\u003e\n\u003ctd\u003eManufacturer rating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater absorption\u003c\/td\u003e\n\u003ctd\u003e5% maximum\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLow-temperature flexibility\u003c\/td\u003e\n\u003ctd\u003ePass at -40 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer datasheet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eService temperature\u003c\/td\u003e\n\u003ctd\u003eNo maximum stated for this profile. EPDM sponge is typically used from about -40 °C to +100 °C (typical for EPDM, not tested on this profile)\u003c\/td\u003e\n\u003ctd\u003eAsk us if your job runs hot\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensional tolerance\u003c\/td\u003e\n\u003ctd\u003eBS 3734 Class E3\u003c\/td\u003e\n\u003ctd\u003eBS 3734\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSupplied as\u003c\/td\u003e\n\u003ctd\u003eOne continuous length: any whole metre from 10 m to 39 m, or a full 40 m coil\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePrice per metre\u003c\/td\u003e\n\u003ctd\u003e£22.23\/m inc VAT for 10 to 39 m; £17.18\/m on the 40 m coil (£687.06)\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003csmall\u003eThe manufacturer gives two foot widths (13.5 mm on its drawing, 14 mm in its written spec) and two sponge compression set figures; we show both. Sponge sections are soft and flexible, so treat all sizes as nominal.\u003c\/small\u003e\u003c\/p\u003e\n\u003ch3\u003eMaterials and compliance\u003c\/h3\u003e\n\u003cp\u003eTwo grades of EPDM extruded together. The foot is solid EPDM, chosen for strength and for holding its shape at high and low temperatures. The bead is expanded (closed-cell sponge) EPDM, which compresses easily and recovers to seal against air and water. The manufacturer describes the material as having outstanding resistance to heat, ozone and weathering, good resistance to steam and polar substances, resistance to ketones and dilute acids and alkalis, and good electrical insulating properties. Like all EPDM it is not suited to oils, fuels or most solvents.\u003c\/p\u003e\n\u003cp\u003eThe manufacturer does \u003cstrong\u003enot\u003c\/strong\u003e state any food-contact (FDA, EC 1935\/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.\u003c\/p\u003e\n\u003ch3\u003eHow it fits\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-door-seal-15mm-x-18mm-fitted-open-and-closed.png?v=1795310992\" alt=\"Illustration: the 15 x 18 mm sponge door seal stuck to a door frame, standing 18 mm tall with the door open and squeezed to 12 mm when the door is closed, shown against a millimetre rule\" width=\"2000\" height=\"2000\" loading=\"lazy\" style=\"width:100%;max-width:640px;height:auto\"\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eMeasure the closed gap.\u003c\/strong\u003e It must be under 18 mm so the bead is squeezed. About 10 to 14 mm (roughly 20 to 45% squeeze) is a good starting point; this is our guidance, not a manufacturer figure. For gaps under about 9 mm choose a smaller seal (see the table below), or the door will be hard to shut.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck the landing.\u003c\/strong\u003e The face you stick to should be flat and at least 14 mm wide. The flat foot goes on the frame; the round bead faces the door. The bead is 15 mm wide, so it overhangs the foot slightly on each side.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean and dry.\u003c\/strong\u003e Wipe the surface with isopropyl alcohol and let it dry. Fit above about 10 °C so the adhesive grabs well.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePeel and press.\u003c\/strong\u003e Peel the liner a little at a time and press the foot down firmly along its length. Do not stretch it, or it will shrink back and open gaps at the ends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorners and joins.\u003c\/strong\u003e It follows gentle curves. At tight 90° corners, cut and butt or mitre the ends rather than forcing a bend, which kinks the bead. Make joins at the top of a door, where water will not sit; a spot of instant adhesive on the ends gives a fully sealed join.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eAdd up every edge you want to seal and allow about 5% for trimming. A standard 2 m × 0.8 m door needs about 5.6 m for three sides and 6.4 m all round; a van rear barn door pair typically takes 8 to 10 m. Every length is cut as one continuous piece, so you can run several doors from one order. From 31 m upwards the full 40 m coil costs less than a cut length.\u003c\/p\u003e\n\u003ch3\u003eWhich profile do I need?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth scope=\"col\"\u003eProfile\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eSize (W × H)\u003c\/th\u003e\n\u003cth scope=\"col\"\u003eBest for\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-door-seal-9mm-x-7mm-white-adhesive-backed-100m-coil\"\u003eEPDM sponge door seal (white)\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e9 × 7 mm\u003c\/td\u003e\n\u003ctd\u003eSmall gaps on interior doors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-d-section-10mm-x-8mm-per-metre\"\u003eEPDM sponge D section\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e10 × 8 mm\u003c\/td\u003e\n\u003ctd\u003eMedium gaps, single hollow D bulb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-d-section-12mm-x-10mm-75m-coil\"\u003eEPDM sponge D section\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e12 × 10 mm\u003c\/td\u003e\n\u003ctd\u003eMedium gaps, wider D bulb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-door-seal-10mm-x-15mm-per-metre\"\u003eEPDM sponge door seal, figure-8\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e10 × 15 mm\u003c\/td\u003e\n\u003ctd\u003eClosed gaps of about 8 to 11 mm on a narrow 10 mm landing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEPDM sponge door seal, dual hardness (this item)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003e15 × 18 mm\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eClosed gaps of about 10 to 14 mm, wide or uneven frames\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-door-seal-16mm-x-14mm-d-profile-cut-length\"\u003eEPDM sponge door seal, D profile\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e16 × 14 mm\u003c\/td\u003e\n\u003ctd\u003eWide D bulb for large, flat landings\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-boot-seal-16mm-x-13-5mm-per-metre\"\u003eEPDM sponge boot seal\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e16 × 13.5 mm\u003c\/td\u003e\n\u003ctd\u003ePush-on over a panel edge instead of an adhesive foot\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-sponge-t-seal-19mm-x-16-5mm-per-metre\"\u003eEPDM sponge T seal\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e19 × 16.5 mm\u003c\/td\u003e\n\u003ctd\u003eLarger section for wider gaps\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat gap will it seal?\u003c\/strong\u003e\u003cbr\u003eAny closed gap under its 18 mm height. Aim for about 10 to 14 mm. For smaller gaps the door will be stiff to close, so choose the 10 × 15 mm or a D section instead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat does \"15 × 18 mm\" mean?\u003c\/strong\u003e\u003cbr\u003eThe bead is 15 mm across and the whole seal is 18 mm tall from the bottom of the foot to the top of the bead. The foot is 13.5 to 14 mm wide.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it self-adhesive?\u003c\/strong\u003e\u003cbr\u003eYes. The underside of the foot carries adhesive tape with a peel-off liner. It sticks to clean, dry painted metal, bare metal, wood, glass, most rigid plastics and rubber.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich way up does it go?\u003c\/strong\u003e\u003cbr\u003eThe flat foot with the adhesive goes on the frame or flange. The round sponge bead faces the closing door.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy two hardnesses?\u003c\/strong\u003e\u003cbr\u003eA soft bead on its own would roll over and peel off; a hard one would make the door difficult to shut. The firm foot holds the seal upright and gives the adhesive a stiff, flat surface, while the soft bead does the sealing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I cut and join it?\u003c\/strong\u003e\u003cbr\u003eA sharp craft knife or scissors gives a clean square end. Butt the ends tightly; for a fully sealed join, glue the ends together with instant adhesive.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it go round corners?\u003c\/strong\u003e\u003cbr\u003eIt follows gentle curves and radiused frames. For sharp 90° corners, cut and butt or mitre the strip so the bead does not kink or lift.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat temperatures can it take?\u003c\/strong\u003e\u003cbr\u003eThe manufacturer states it passes a -40 °C flexibility test and the solid foot is heat-aged at 70 °C with no change in hardness, but no maximum is given for this profile. EPDM sponge is typically used up to about +100 °C (typical for the material, not tested on this profile). The adhesive may soften first, so ask us about hot jobs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it outdoors?\u003c\/strong\u003e\u003cbr\u003eYes. Ozone, weather and UV resistance are rated excellent, mould resistance is very good, and water absorption is 5% maximum.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it stand up to oil or fuel?\u003c\/strong\u003e\u003cbr\u003eNo. EPDM handles water, steam, weather and dilute acids and alkalis well, but swells in oils, fuels and most solvents.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow is it supplied?\u003c\/strong\u003e\u003cbr\u003eAs one continuous piece in the length you choose, from 10 m to 39 m, or as a full 40 m coil. The coil is cheaper per metre, and from 31 m upwards it is cheaper outright.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it food-safe or WRAS approved?\u003c\/strong\u003e\u003cbr\u003eNo approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.\u003c\/p\u003e\n\u003ch3\u003eDelivery and help\u003c\/h3\u003e\n\u003cp\u003eHeld in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.\u003c\/p\u003e","brand":"Industrial Polymers","offers":[{"title":"10m","offer_id":56592908091771,"sku":"IP-EPDMDS-15X18-10M","price":222.27,"currency_code":"GBP","in_stock":true},{"title":"11m","offer_id":56592908124539,"sku":"IP-EPDMDS-15X18-11M","price":244.47,"currency_code":"GBP","in_stock":true},{"title":"12m","offer_id":56592908157307,"sku":"IP-EPDMDS-15X18-12M","price":266.7,"currency_code":"GBP","in_stock":true},{"title":"13m","offer_id":56592908190075,"sku":"IP-EPDMDS-15X18-13M","price":288.93,"currency_code":"GBP","in_stock":true},{"title":"14m","offer_id":56592908222843,"sku":"IP-EPDMDS-15X18-14M","price":311.16,"currency_code":"GBP","in_stock":true},{"title":"15m","offer_id":56592908255611,"sku":"IP-EPDMDS-15X18-15M","price":333.39,"currency_code":"GBP","in_stock":true},{"title":"16m","offer_id":56592908288379,"sku":"IP-EPDMDS-15X18-16M","price":355.62,"currency_code":"GBP","in_stock":true},{"title":"17m","offer_id":56592908321147,"sku":"IP-EPDMDS-15X18-17M","price":377.82,"currency_code":"GBP","in_stock":true},{"title":"18m","offer_id":56592908353915,"sku":"IP-EPDMDS-15X18-18M","price":400.05,"currency_code":"GBP","in_stock":true},{"title":"19m","offer_id":56592908386683,"sku":"IP-EPDMDS-15X18-19M","price":422.28,"currency_code":"GBP","in_stock":true},{"title":"20m","offer_id":56592908419451,"sku":"IP-EPDMDS-15X18-20M","price":444.51,"currency_code":"GBP","in_stock":true},{"title":"21m","offer_id":56592908452219,"sku":"IP-EPDMDS-15X18-21M","price":466.74,"currency_code":"GBP","in_stock":true},{"title":"22m","offer_id":56592908484987,"sku":"IP-EPDMDS-15X18-22M","price":488.97,"currency_code":"GBP","in_stock":true},{"title":"23m","offer_id":56592908517755,"sku":"IP-EPDMDS-15X18-23M","price":511.2,"currency_code":"GBP","in_stock":true},{"title":"24m","offer_id":56592908550523,"sku":"IP-EPDMDS-15X18-24M","price":533.4,"currency_code":"GBP","in_stock":true},{"title":"25m","offer_id":56592908583291,"sku":"IP-EPDMDS-15X18-25M","price":555.63,"currency_code":"GBP","in_stock":true},{"title":"26m","offer_id":56592908616059,"sku":"IP-EPDMDS-15X18-26M","price":577.86,"currency_code":"GBP","in_stock":true},{"title":"27m","offer_id":56592908648827,"sku":"IP-EPDMDS-15X18-27M","price":600.09,"currency_code":"GBP","in_stock":true},{"title":"28m","offer_id":56592908681595,"sku":"IP-EPDMDS-15X18-28M","price":622.32,"currency_code":"GBP","in_stock":true},{"title":"29m","offer_id":56592908714363,"sku":"IP-EPDMDS-15X18-29M","price":644.55,"currency_code":"GBP","in_stock":true},{"title":"30m","offer_id":56592908747131,"sku":"IP-EPDMDS-15X18-30M","price":666.78,"currency_code":"GBP","in_stock":true},{"title":"31m","offer_id":56592908779899,"sku":"IP-EPDMDS-15X18-31M","price":688.98,"currency_code":"GBP","in_stock":true},{"title":"32m","offer_id":56592908812667,"sku":"IP-EPDMDS-15X18-32M","price":711.21,"currency_code":"GBP","in_stock":true},{"title":"33m","offer_id":56592908845435,"sku":"IP-EPDMDS-15X18-33M","price":733.44,"currency_code":"GBP","in_stock":true},{"title":"34m","offer_id":56592908878203,"sku":"IP-EPDMDS-15X18-34M","price":755.67,"currency_code":"GBP","in_stock":true},{"title":"35m","offer_id":56592908910971,"sku":"IP-EPDMDS-15X18-35M","price":777.9,"currency_code":"GBP","in_stock":true},{"title":"36m","offer_id":56592908943739,"sku":"IP-EPDMDS-15X18-36M","price":800.13,"currency_code":"GBP","in_stock":true},{"title":"37m","offer_id":56592908976507,"sku":"IP-EPDMDS-15X18-37M","price":822.33,"currency_code":"GBP","in_stock":true},{"title":"38m","offer_id":56592909009275,"sku":"IP-EPDMDS-15X18-38M","price":844.56,"currency_code":"GBP","in_stock":true},{"title":"39m","offer_id":56592909042043,"sku":"IP-EPDMDS-15X18-39M","price":866.79,"currency_code":"GBP","in_stock":true},{"title":"40m full coil","offer_id":56592909074811,"sku":"IP-EPDMDS-15X18-40M","price":687.06,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-sponge-door-seal-15mm-x-18mm-cut-lengths-studio.jpg?v=1795179933","url":"https:\/\/industrial-polymers.co.uk\/products\/epdm-sponge-door-seal-15mm-x-18mm-cut-lengths","provider":"Industrial-polymers ","version":"1.0","type":"link"}