{"product_id":"epdm-square-u-channel-9-2mm-x-15mm-for-6mm-panels-50m-coil","title":"EPDM Square U Channel – 9.2mm x 15mm for 6mm Panels – 50m Coil","description":"\u003cp\u003e\u003cstrong\u003eA tall, slim, solid black EPDM square U channel that pushes onto 6 mm panel, sheet and glass edges and grips them deeply.\u003c\/strong\u003e It measures 9.2 mm wide by 15 mm high. The 6 mm slot runs 13.4 mm deep between two thin 1.6 mm walls, under a 1.6 mm solid base that covers the cut edge. Because the walls are thin, the finished edge is only 3.2 mm wider than the panel. You get a neat, square, cushioned edge that hides sharp or rough cuts and stays put on long runs. EPDM is rated from −40 °C to +120 °C and resists weather and ozone, so it suits warm machinery as well as outdoor doors and hatches. It comes as one continuous 50 m coil, held in UK stock for same-day dispatch.\u003c\/p\u003e\n\n\u003ch3\u003eAt a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e panels, sheet and glazing 6 mm thick\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 9.2 mm wide × 15 mm high; 6 × 13.4 mm slot; 1.6 mm walls; 1.6 mm base\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e solid EPDM rubber, 65° Shore A, black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrength:\u003c\/strong\u003e 9 MPa tensile strength\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature:\u003c\/strong\u003e −40 °C to +120 °C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 80 g per metre, about 4 kg per coil\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e one continuous 50 m coil, about £8.42 per metre\u003c\/li\u003e\n\u003cli\u003ePush-on fit with no tools. It cuts cleanly with a knife and is 100 % recyclable.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eTechnical drawing\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-square-u-channel-9-2mm-x-15mm-technical-drawing.png?v=1795186078\" alt=\"Technical drawing of the EPDM square U channel: 9.2 mm wide, 15 mm high, 6 mm slot 13.4 mm deep, 1.6 mm walls and 1.6 mm base\" width=\"2000\" height=\"1490\" loading=\"lazy\" style=\"width:100%;height:auto\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eAll dimensions are in mm and nominal. The 13.4 mm slot depth is the 15 mm height minus the 1.6 mm base. The 1.6 mm walls are the 9.2 mm width minus the 6 mm slot, split over two walls, and match the manufacturer's stated 1.6 mm thickness. The drawing is not to scale.\u003c\/small\u003e\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003cth\u003eTest method \/ basis\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eProfile\u003c\/td\u003e\n\u003ctd\u003eSquare U channel: straight parallel walls, parallel slot, flat base\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall width\u003c\/td\u003e\n\u003ctd\u003e9.2 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing and listing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall height\u003c\/td\u003e\n\u003ctd\u003e15 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing and listing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSlot (channel) width\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing and listing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSlot depth (grip depth)\u003c\/td\u003e\n\u003ctd\u003e13.4 mm\u003c\/td\u003e\n\u003ctd\u003eCalculated: 15 − 1.6 mm base\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWall thickness\u003c\/td\u003e\n\u003ctd\u003e1.6 mm each side\u003c\/td\u003e\n\u003ctd\u003eManufacturer (\"thickness 1.6 mm\"); matches (9.2 − 6) ÷ 2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBase thickness over the edge\u003c\/td\u003e\n\u003ctd\u003e1.6 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePanel thickness it fits\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFinished edge width on a 6 mm panel\u003c\/td\u003e\n\u003ctd\u003e9.2 mm (3.2 mm wider than the panel)\u003c\/td\u003e\n\u003ctd\u003eCalculated from the drawing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaterial\u003c\/td\u003e\n\u003ctd\u003eSolid EPDM (ethylene propylene diene monomer)\u003c\/td\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eColour\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness\u003c\/td\u003e\n\u003ctd\u003e65° Shore A\u003c\/td\u003e\n\u003ctd\u003eManufacturer; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile strength\u003c\/td\u003e\n\u003ctd\u003e9 MPa\u003c\/td\u003e\n\u003ctd\u003eManufacturer; method not stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum working temperature\u003c\/td\u003e\n\u003ctd\u003e+120 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum working temperature\u003c\/td\u003e\n\u003ctd\u003e−40 °C\u003c\/td\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e80 g per metre (about 4.0 kg per 50 m coil)\u003c\/td\u003e\n\u003ctd\u003eManufacturer; coil weight calculated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElongation at break\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTear strength\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompression set\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDensity\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensional tolerance\u003c\/td\u003e\n\u003ctd\u003eNot stated for this profile; dimensions are nominal\u003c\/td\u003e\n\u003ctd\u003eAsk us if you need it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSupplied as\u003c\/td\u003e\n\u003ctd\u003eOne continuous 50 m coil\u003c\/td\u003e\n\u003ctd\u003e—\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003ePrice\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003ePack\u003c\/th\u003e\n\u003cth\u003ePrice inc VAT\u003c\/th\u003e\n\u003cth\u003ePer metre\u003c\/th\u003e\n\u003cth\u003eApprox. weight\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e50 m coil\u003c\/td\u003e\n\u003ctd\u003e£420.93\u003c\/td\u003e\n\u003ctd\u003e£8.42\u003c\/td\u003e\n\u003ctd\u003e4.0 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003csmall\u003eNeed less than 50 m? Our \u003ca href=\"\/products\/rubber-square-u-channel-6mm-panel-x-16mm-high-x-3-1mm-wall-per-metre\"\u003eEPDM square U channel for 6 mm panels, 16 mm high with 3.1 mm walls\u003c\/a\u003e is sold by the metre. Its walls are thicker, so the finished edge is wider. The \u003ca href=\"\/products\/epdm-square-u-channel-9mm-x-8mm-for-6mm-panels-cut-length\"\u003e9 × 8 mm channel for 6 mm panels\u003c\/a\u003e comes in cut lengths, with a shallower grip.\u003c\/small\u003e\u003c\/p\u003e\n\n\u003ch3\u003eMaterials and compliance\u003c\/h3\u003e\n\u003cp\u003eThis profile is made from solid EPDM, a synthetic rubber known for its resistance to weather, ozone and UV. The manufacturer states that it is 100 % recyclable and rates it from −40 °C to +120 °C. The manufacturer does not state any food-contact (FDA, EC 1935\/2004), drinking-water (WRAS), fire-rating, REACH, RoHS or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required. Ask us for a certified alternative.\u003c\/p\u003e\n\n\u003ch3\u003eHow it fits\u003c\/h3\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-square-u-channel-9-2mm-x-15mm-how-it-fits.png?v=1795186078\" alt=\"How the 9.2 x 15 mm EPDM square U channel fits over a 6 mm panel edge, with four fitting steps\" width=\"2000\" height=\"2000\" loading=\"lazy\" style=\"width:100%;max-width:700px;height:auto\"\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck the edge.\u003c\/strong\u003e Deburr, clean and dry it, and check the panel is about 6 mm thick.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePush on.\u003c\/strong\u003e Start at one end and press the channel down along the edge by hand. The slot is 13.4 mm deep, so on long runs a little soapy water helps it slide fully home. A soft mallet also helps. You need no other tools.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCut and join.\u003c\/strong\u003e Cut slightly over-length with a sharp knife or shears, then push the ends together into a tight butt joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBond if needed.\u003c\/strong\u003e Where there is vibration, or where you need a sealed fit (for example round an aluminium window channel), run a bead of polyurethane or silicone sealant into the slot before fitting.\u003c\/li\u003e\n\u003c\/ol\u003e\n\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eAdd up every edge you want to cover, allow about 5 % for corners and waste, then divide by 50. For example, twelve machine guard panels each 1.2 m × 0.9 m have 50.4 m of edge. With 5 % added that is about 53 m, so you need two 50 m coils. Ten of the same panels (42 m, about 44 m with waste) fit on one coil.\u003c\/p\u003e\n\n\u003ch3\u003eTypical uses\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eEdging 6 mm sheet metal doors, hatches, covers and machine guards\u003c\/li\u003e\n\u003cli\u003eProtecting cut edges on machinery and enclosure panels near heat, up to 120 °C\u003c\/li\u003e\n\u003cli\u003eEdge protection on 6 mm glass, acrylic and polycarbonate panels and shelves\u003c\/li\u003e\n\u003cli\u003eKnock protection on vending machines, cabinets, kiosks and furniture panels\u003c\/li\u003e\n\u003cli\u003eSafety edging on stairs, step plates and running boards\u003c\/li\u003e\n\u003cli\u003eOutdoor trailers, kiosks and equipment covers, where EPDM's weather resistance helps\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich one do I need?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProfile\u003c\/th\u003e\n\u003cth\u003eFits panel\u003c\/th\u003e\n\u003cth\u003eChoose it when\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-square-u-channel-7-5mm-x-15mm-for-4-5mm-panels-50m-coil\"\u003eEPDM 7.5 × 15 mm\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e4.5 mm\u003c\/td\u003e\n\u003ctd\u003eYour panels are 4.5 mm thick; 50 m coil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-square-u-channel-9-2mm-x-10mm-cut-to-length\"\u003eEPDM 9.2 × 10 mm\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e4.75 mm\u003c\/td\u003e\n\u003ctd\u003eYour panels are 4.75 mm (3\/16\") thick; cut lengths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEPDM 9.2 × 15 mm (this item)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003e6 mm panels, slim walls, deep grip, heat up to 120 °C; 50 m coil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/epdm-square-u-channel-9mm-x-8mm-for-6mm-panels-cut-length\"\u003eEPDM 9 × 8 mm\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003eYou want a low-profile bead in cut lengths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/tpe-square-u-channel-12mm-x-14mm-for-6mm-panels-25m-coil\"\u003eTPE 12 × 14 mm\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003eYou want heavier 3 mm walls on a 25 m coil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/rubber-square-u-channel-6mm-panel-x-16mm-high-x-3-1mm-wall-per-metre\"\u003eEPDM 6 mm panel × 16 mm, per metre\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e6 mm\u003c\/td\u003e\n\u003ctd\u003eYou only need a few metres\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat thickness of panel does it fit?\u003c\/strong\u003e\u003cbr\u003eIt is made for 6 mm material. On 5 mm sheet it will be loose unless you bond a thin rubber strip inside the slot to pack it out, or glue it on. For thicker material choose a channel with a wider slot. To make the finished edge wider, a neoprene strip can be bonded alongside it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy choose a 15 mm tall channel?\u003c\/strong\u003e\u003cbr\u003eThe extra height gives a 13.4 mm deep slot, so the channel grips much more of the edge than a shallow channel. It is less likely to peel off on long runs, curves or edges that get knocked, and it hides more of a rough or uneven cut.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it stay on without glue?\u003c\/strong\u003e\u003cbr\u003eOn a clean 6 mm edge, the deep slot holds the channel by grip alone in most static uses. On moving doors, vibrating machinery or outdoor parts, bond it with polyurethane or silicone sealant.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat temperatures can it take?\u003c\/strong\u003e\u003cbr\u003eThe manufacturer rates it from −40 °C to +120 °C, so it suits cold stores, outdoor equipment and panels near warm machinery.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan it be used outdoors?\u003c\/strong\u003e\u003cbr\u003eYes. EPDM is one of the most weather-resistant rubbers, with good resistance to sunlight, ozone and rain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I cut and join it?\u003c\/strong\u003e\u003cbr\u003eCut it with a sharp knife, shears or a fine-tooth saw for a square end. Butt the ends tightly together. For a sealed joint, bond the ends with a flexible adhesive or sealant. To go round a corner, mitre the channel or cut a small V-notch in the base so it bends without lifting.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy EPDM rather than TPE?\u003c\/strong\u003e\u003cbr\u003eThis EPDM channel is rated up to 120 °C, so it is the better choice near heat or in strong sun. TPE channels are a good alternative for general indoor edging.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it oil resistant?\u003c\/strong\u003e\u003cbr\u003eEPDM is not recommended for contact with mineral oils, petrol or diesel. For oily areas, ask us about a nitrile or neoprene channel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it food safe or WRAS approved?\u003c\/strong\u003e\u003cbr\u003eNo approvals are stated for this profile, so do not use it where food-contact or drinking-water certification is needed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it in stock?\u003c\/strong\u003e\u003cbr\u003eYes. We hold it in stock as a continuous 50 m coil, ready for same-day dispatch.\u003c\/p\u003e\n\n\u003cp\u003eNeed help choosing or fitting? Call \u003ca href=\"tel:+441282277786\"\u003e+44 1282 277786\u003c\/a\u003e, email \u003ca href=\"mailto:sales@industrial-polymers.co.uk\"\u003esales@industrial-polymers.co.uk\u003c\/a\u003e or \u003ca href=\"\/pages\/contact\"\u003econtact our team\u003c\/a\u003e.\u003c\/p\u003e","brand":"Industrial Polymers","offers":[{"title":"50m coil","offer_id":56590479524219,"sku":"IP-EPDMU-9.2X15X6-STD","price":420.93,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0579\/7776\/6024\/files\/epdm-square-u-channel-9-2mm-x-15mm-black-end-view.png?v=1795186079","url":"https:\/\/industrial-polymers.co.uk\/products\/epdm-square-u-channel-9-2mm-x-15mm-for-6mm-panels-50m-coil","provider":"Industrial-polymers ","version":"1.0","type":"link"}