
Rubber & FoamSKU IP-TPEB-80X40-STD
TPE B Fender – Solid 80mm x 40mm, Non-Marking – 25m Coil
TPE B fender 80mm x 40mm is a solid, non-marking fender profile with twin rounded faces and a central channel, used to absorb knocks on boat gunwales, pontoon edges, loading bays and vehicle bodies. It is sold as a single 25m coil.
At a glance
- Solid B-section fender: 80mm wide x 40mm deep
- Two 20mm rounded faces either side of a 25mm-deep central channel
- Non-marking thermoplastic elastomer (TPE), 68 Shore A
- 700% elongation at break for good impact recovery
- Works from -50°C to +75°C
- One continuous 25m coil for long runs with few joints
Typical uses
- Gunwale and rubbing strake fender on workboats, ribs and tenders
- Edge protection on pontoons, jetties and quay walls
- Rubbing strip on loading bay edges and factory walls
- Impact strip on trucks, ambulances and commercial vehicle bodies
Which one do I need?
| Fender | Best suited to |
|---|---|
| Neoprene B fender 51mm x 25mm | Smaller boats and light-duty rubbing strips |
| Compact TPE D fender 50mm x 30mm | Lighter non-marking D profile in the same coil length |
| EPDM B fender 76mm x 32mm | Similar width in EPDM rubber, 12m roll |
| TPE B fender 80mm x 40mm (this fender) | Heavy, non-marking protection for workboats, pontoons and loading bays |
| Hollow TPE delta D fender 60mm x 52mm | Deeper hollow section that compresses more on impact |
Technical drawing
Specification
| Profile | Solid B fender with central channel |
| Size | 80mm wide x 40mm deep |
| Face channel | 25mm deep between two 20mm rounded faces |
| Material | TPE (thermoplastic elastomer), non-marking |
| Colour | Black |
| Hardness | 68 Shore A |
| Density | 1.09 g/cm³ |
| Tensile strength | 7.8 MPa |
| Elongation at break | 700% |
| Temperature range | -50°C to +75°C |
| Unit of sale | 25m coil |
How much do I need?
Measure each edge to be protected and add about 5% for trimming and corners. For example, fendering both sides of a 7m workboat needs 2 x 7m = 14m, plus 5% = 14.7m, and four 2.5m loading bay edges add another 10.5m: one 25m coil covers both jobs.
Fitting tips
- Fix through the base of the central channel so screw heads sit below the rubbing faces.
- Pre-drill at roughly 200mm to 300mm centres and use marine-grade stainless fixings on boats.
- Fit the fender in long straight runs and warm it slightly to follow curves.
- Seal fixing holes on boats with a marine sealant to keep water out of the hull.
Complete your project
- EPDM Rubber B Fender – 76mm x 32mm – 12m Roll
- Compact TPE D Fender – 50mm x 30mm – 25m Coil
- Hollow TPE Delta D Fender – 60mm x 52mm – 10m Coil
Questions
Will this fender mark my boat or walls?
No. The TPE compound is non-marking, so it does not leave black streaks on hulls, paint or walls when it rubs.
What is the channel in the face for?
It gives a recessed line for the fixings, keeping screw heads clear of the rubbing faces.
Is a B fender better than a D fender?
The B section spreads impact over two rounded faces and hides the fixings; a D fender has one smooth face and is often chosen for lighter duty.
Can it be used outdoors?
Yes. The TPE resists weathering and works from -50°C to +75°C.
Need help choosing a fender? Contact our technical team and we will be glad to advise.
Product details
| SKU | IP-TPEB-80X40-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE B Fender – Solid 80mm x 40mm, Non-Marking – 25m Coil