
Rubber & FoamSKU IP-EPDMD-12.5X9.5-8M
EPDM D Section Door Seal – 12.5mm x 9.5mm, Push-On for 1mm Panels (Aston Martin 030-017-0019) – Cut Length or 30m Coil
Price shown updates with the option you pick.
A hollow D-section door seal in solid black EPDM rubber, 12.5 mm wide and 9.5 mm high, with a push-on slot that grips a 1 mm panel or flange edge. Cut to any whole length from 8 m to 29 m, or buy full 30 m coils. The rounded bulb closes the gap round doors, hatches and lids and cushions the edge against knocks, while the slot holds it in place without adhesive. It is a direct replacement for Aston Martin OEM part 030-017-0019, the A/B post (shut pillar) seal on the DB4, DB5, DB6, DBS, AMV8 and V8 up to 2000.
At a glance
- Size: 12.5 mm wide × 9.5 mm high; 8.5 mm base with a 1.5 mm lower lip
- Fixing: push-on slot for a 1 mm thick panel, flange or sheet edge
- Material: solid (dense) EPDM rubber, 65–75 IRHD
- Tested: 10 MPa tensile, 500 % elongation, 50 kN/m tear, 21 % compression set (22 h at 70 °C), no cracks after ozone exposure
- Outdoors: EPDM resists weather, UV and ozone, so it works inside and out
- Lengths: 8 m to 29 m at £17.19 per metre, or a 30 m coil at £387.00 (£12.90 per metre)
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- A/B post and shut pillar door seals on classic Aston Martins (replaces 030-017-0019) and other classic cars
- Door, locker and hatch seals on caravans, buses, coaches and rail vehicles
- Weather seals on marine hatches and lockers, and aircraft ground equipment
- Edge seal and soft bump strip on 1 mm steel cabinet, enclosure and machine-guard doors
- Window and panel closure seals where a degree of impact protection is needed
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Hollow D (bulb) with push-on panel slot underneath | Manufacturer's drawing |
| Overall width | 12.5 mm | Manufacturer's drawing |
| Overall height | 9.5 mm | Manufacturer's drawing |
| Base width (lower lip length) | 8.5 mm | Manufacturer's drawing |
| Lower lip thickness | 1.5 mm | Manufacturer's drawing |
| Fits panel / flange thickness | 1 mm | Manufacturer's data sheet |
| Bulb height | approx. 7 mm | Scaled from the manufacturer's drawing, not stated |
| Hollow core | approx. 9.7 × 4.4 mm | Scaled from the manufacturer's drawing, not stated |
| Wall thickness | approx. 1.3–1.4 mm | Scaled from the manufacturer's drawing, not stated |
| Material | EPDM rubber (solid, not sponge) | Manufacturer's data sheet |
| Colour | Black | Manufacturer |
| Hardness | 65–75 IRHD, ±5 | IRHD |
| Tensile strength | 10.0 MPa | Manufacturer's data sheet |
| Elongation at break | 500 % | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21 % | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm ozone |
| Heat ageing: change in tensile strength | +9 % | 70 h at 70 °C |
| Heat ageing: change in elongation at break | 0 % | 70 h at 70 °C |
| Service temperature | about −40 °C to +120 °C (typical for EPDM, not tested on this profile) | General EPDM data |
| Density | not stated by the manufacturer | – |
| Dimensional tolerance | not stated by the manufacturer | – |
| Supplied as | Cut lengths 8–29 m (one piece), or 30 m coils | – |
| Replaces | Aston Martin 030-017-0019 (A/B post / shut pillar seal) | Manufacturer |
| Our part number | IP-EPDMD-12.5X9.5 | – |
Materials and compliance
Made from a general-purpose EPDM rubber compound with good weathering, UV, ozone, heat and cold resistance, good abrasion resistance and good resistance to flexing fatigue. The manufacturer describes it as 100 % recyclable. The manufacturer does not state any food-contact, potable-water (WRAS), fire-rating, REACH or RoHS approval for this profile in its text, so we do not claim any. Ask us if you need a compliance declaration for your project.
How much do I need?
Measure the full length of every edge you want to seal and round up to the next whole metre. The smallest cut length is 8 m. Lengths up to 29 m are cut as one continuous piece. From 23 m upwards a full 30 m coil costs less than a cut length, so choose the coil. Need more than 30 m? Choose 60 m or 90 m (supplied as 30 m coils).
Fitting

- Clean the 1 mm edge and remove burrs so the slot slides on without tearing.
- Start at a lower corner, with the bulb facing the closing door, and push the slot fully home as you work along.
- Ease the seal round corners; do not stretch it, or it will shrink back and leave a gap at the joint.
- For thicker edges (over 1 mm) choose a self-grip edge trim with a wider grip range instead.
Frequently asked questions
Will it fit my Aston Martin?
It replaces OEM part 030-017-0019, the A/B post (shut pillar) seal used on the DB4, DB5, DB6, DBS, AMV8 and V8 models up to 2000. Check the old seal against the drawing before you order.
What panel thickness does the slot fit?
A 1 mm panel, flange or sheet edge. On a thinner edge it may need a few dabs of rubber adhesive in the slot; on a thicker one it will not go on fully.
How big a gap will it seal?
The bulb stands about 7 mm above the slot. As a guide, aim for a closed gap of roughly 4 to 6 mm so the bulb is squeezed but not flattened.
Can it be used outdoors?
Yes. EPDM resists weather, UV and ozone, and this compound showed no cracks in an ozone test (72 h at 40 °C, 25 pphm).
What temperatures can it take?
The manufacturer does not give a service range for this profile. EPDM typically works from about −40 °C to +120 °C, and this compound kept its properties after 70 hours at 70 °C.
How do I cut and join it?
Cut it square with a sharp knife or trimming blade. Butt the ends tightly at the joint; for a sealed join use a cyanoacrylate (superglue) suited to EPDM, with a primer if needed.
Is it sponge or solid rubber?
Solid (dense) EPDM at 65–75 IRHD, so it is firmer and harder-wearing than a sponge seal and also works as a light bump strip.
How is it supplied?
Cut lengths of 8 m to 29 m come as one piece. Coils are 30 m; 60 m and 90 m orders are supplied as two or three 30 m coils.
Need a different size? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMD-12.5X9.5-8M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM D Section Door Seal – 12.5mm x 9.5mm, Push-On for 1mm Panels (Aston Martin 030-017-0019) – Cut Length or 30m Coil