
Rubber & FoamSKU IP-BNRT-3X25-25X31.5
Black Neoprene Rubber Tubing – 3mm to 25mm Bore – 10m Roll
Price shown updates with the option you pick.
Black neoprene rubber tubing is a flexible, hard-wearing hose for water, air, gases and diluted acids in workshops, laboratories and outdoor pumping. Choose from 14 bore and wall combinations between 3mm and 25mm bore; each is sold as a 10m roll.
At a glance
- 14 sizes from 3mm bore x 4.5mm OD up to 25mm bore x 31.5mm OD
- Standard and heavy wall options for kink and wear resistance
- Neoprene, 60–70° Shore A, black
- Working range -30°C to +100°C
- Conforms to BS 2775:1987 for general laboratory use
- Good resistance to weathering, ageing and abrasion
Typical uses
- General transfer of water, air and other fluids
- Laboratory gas taps and bench equipment
- Pond filters, pumps and outdoor water lines
- Transfer of diluted acids
- School and college science departments
Which one do I need?
| Size (bore x outside diameter) | Best for |
|---|---|
| 3mm x 4.5mm to 6.5mm x 9.5mm | Small-bore lab and instrument lines, tight routing |
| 8mm x 12mm to 12.5mm x 17mm | Gas taps, bench equipment and general fluid transfer |
| 16mm x 22.5mm to 25mm x 31.5mm | Higher flow water lines, pumps and pond filters |
| Heavy wall: 3mm x 9mm, 5mm x 13mm, 6.5mm x 16.5mm, 8mm x 20mm, 10mm x 24mm | Rough handling, outdoor use and better kink resistance |
Technical drawing
Specification
| Material | Neoprene rubber |
| Colour | Black |
| Bore sizes | 3mm, 5mm, 6.5mm, 8mm, 10mm, 12.5mm, 16mm, 20mm, 25mm |
| Outside diameters | 4.5mm to 31.5mm (see size options) |
| Hardness | 60–70° Shore A |
| Working temperature | -30°C to +100°C |
| Tensile strength | 7.6 MPa |
| Elongation at break | 380% |
| Specific gravity | 1.46 g/cm³ |
| Standard | BS 2775:1987 |
| Unit of sale | 10m roll per size |
How much do I need?
Measure the run between fittings and add about 100mm at each end for pushing on and clipping. Example: three lab benches each needing a 2.5m gas line use 3 x (2.5m + 0.2m) = 8.1m, so one 10m roll is enough. Wall thickness = (outside diameter – bore) ÷ 2.
Fitting tips
- Choose a bore equal to or slightly smaller than the spigot outside diameter for a tight push fit.
- Use hose clips on pressurised or permanent joints.
- Cut square with sharp shears or a knife; a ragged end will not seal.
- Keep runs away from sharp edges and hot surfaces above 100°C.
Complete your project
- TPV Thermoplastic Rubber Tubing – Abrasion Resistant Grade – 15m Roll
- Platinum Cured Silicone Dairy Tubing – Translucent – 10m or 20m Roll
- White Silicone Sponge Cord – Closed Cell – 10m Roll
Questions
Can this neoprene tubing be used outdoors?
Yes. Neoprene resists weathering and ageing, so it suits pond filters, pumps and other outdoor lines.
Is it suitable for oil?
It has medium resistance to petroleum-based oils and suits intermittent contact, but may deteriorate with long exposure. It is not suitable for ester lubricants.
Can it be used for electrical insulation?
No. This compound is not an electrical insulator and should not be used where insulation is needed.
How do I work out the wall thickness?
Subtract the bore from the outside diameter and halve it. For example 10mm bore x 14mm OD has a 2mm wall.
Is each size a full roll?
Yes. Every size option is a continuous 10m roll.
Not sure which size or grade suits your application? Contact our team and we will help you choose.
Product details
| SKU | IP-BNRT-3X25-25X31.5 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black Neoprene Rubber Tubing – 3mm to 25mm Bore – 10m Roll