
Rubber & FoamSKU IP-IPRDF-24X16-5
Hollow Rubber D Fender – 24mm x 16mm, 72 Shore A – 5m or 10m Length
Price shown updates with the option you pick.
A compact hollow rubber D fender, 24mm wide and 16mm high. It gives real impact protection where there is no room for a bulky buffer: trailer sides, loading-bay edges, small pontoons, racking, trolleys and machine guards. The flat back sits flush on the surface. The 16mm x 8mm D-shaped bore lets the crown compress on impact, and it takes a flat steel backing bar for a strong through-bolted fixing. It is supplied black in a continuous 5m or 10m length, held in stock and dispatched from the UK.
At a glance
- Size: 24mm wide x 16mm high; bore 16mm x 8mm
- Hardness: 72° Shore A, firm enough for repeated knocks without going brittle
- Weight: 0.3kg per metre (about 1.5kg for 5m, 3kg for 10m)
- Price per metre: £20.40 inc VAT on both lengths
- Fixing: bolt through the base, screw, or fit into a channel
- Workable: cut, drill, chamfer or bend to suit the job
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Hollow D, flat back, single D-shaped bore | Manufacturer drawing and photos |
| Overall width (base) | 24 mm | Manufacturer specification |
| Overall height (projection) | 16 mm | Manufacturer specification |
| Bore width | 16 mm | Manufacturer specification |
| Bore height | 8 mm | Manufacturer specification |
| Wall thickness (sides, crown, base) | ≈ 4 mm | Calculated from outer and bore sizes, not separately specified |
| Length | 5 m or 10 m continuous | Manufacturer specification |
| Weight | 0.3 kg/m | Manufacturer specification |
| Colour | Black | Manufacturer specification |
| Material | EPDM rubber (see note below) | Manufacturer product listing |
| Hardness | 72° Shore A | DIN 53505 |
| Density | 1200 kg/m³ (1.20 g/cm³) | Manufacturer datasheet |
| Tensile strength | 16 MPa | DIN 53504 |
| Elongation at break | 350 % | DIN 53504 |
| Tear resistance | 80 N/cm | DIN 53507 |
| Abrasion loss | 100 mm³ | DIN 53516 |
| Compression set, 24 h at 70 °C | 40 % | DIN 53517 |
| Ozone resistance | No cracking visible | ISO 1431-1 |
| Air ageing: change in hardness | 5 Shore A points | DIN 53505 (ageing conditions not stated) |
| Air ageing: tensile strength | 80 % (as stated by the manufacturer) | DIN 53504 |
| Air ageing: elongation at break | 80 % (as stated by the manufacturer) | DIN 53504 |
| Service temperature | Not published for this profile. Typical for EPDM: about −40 °C to +100 °C (not tested on this profile) | General material data |
| Dimensional tolerance | Not published. Extruded rubber profiles are commonly made to ISO 3302-1 class E2 (typical, not tested on this profile) | General industry practice |
Material note: the manufacturer's product listing describes this fender as EPDM, but the header of its datasheet for the same part names natural rubber. The physical properties above come from that datasheet. If the exact polymer matters for your application, for example oil contact or long outdoor exposure, contact us before ordering and we will confirm it.
Materials and compliance
The manufacturer states no food-contact (FDA, EC 1935/2004), potable-water (WRAS), REACH, RoHS or fire-rating approvals for this product, so we do not claim any. If you need a declaration for your file, ask us and we will request one.
Where it is used
- Small marinas, jetties, pontoons and the rubbing strakes of small boats
- Lorry loading bays and dock edges
- Trailer sides and tail boards
- Car park columns, barriers and wall corners
- Warehouse racking ends, workshop benches, trolleys and cages
- Any edge that takes regular knocks where a large fender will not fit
How to fit it

- Prepare the surface. It should be clean, flat and strong enough to take the impact load.
- Through-bolted (strongest). Slide a flat steel bar into the bore. Drill through the base and the bar, then drill a larger access hole in the crown above each bolt so the bolt head can drop in. Space bolts at up to 450mm centres, with extra screws at up to 300mm centres if needed. Carry the bar past any butt joint and fix it into the next length.
- Surface screwed. For light duty, screw through the base with a large washer under each head.
- Channel mounted. Retain the base in a channel or between welded angle strips spaced to the 24mm base width.
- Fixings. Use galvanised or stainless steel fixings, especially outdoors or near water.
Prices
| Length | Price inc VAT | Per metre | Approx. weight |
|---|---|---|---|
| 5 m | £102.00 | £20.40 | 1.5 kg |
| 10 m | £204.00 | £20.40 | 3.0 kg |
Frequently asked questions
Which way up does it fit?
The wide flat side is the back. It goes against the surface you are protecting, and the rounded crown faces the impact.
How do I choose between 24 x 16mm and a larger fender?
This size suits low-speed knocks from trolleys, pallet trucks, small boats and vehicles reversing slowly. It sticks out only 16mm. For HGV docks or larger vessels, choose a deeper profile such as our 32 x 22mm or 40 x 25mm D fenders.
Can it be used outdoors and near salt water?
Yes, it is used on jetties, quays and trailers. Use galvanised or stainless fixings. If it will be in long-term direct sun, ask us to confirm the polymer (see the material note above).
What temperatures can it handle?
The manufacturer does not publish a range for this profile. Rubber fenders of this type are normally used from below freezing up to warm summer surface temperatures without trouble. For heat sources or freezer rooms, contact us first.
How do I cut and join it?
Cut it square with a sharp knife or a fine saw, using a mitre block for corners. Butt the ends tightly and support each joint with the backing bar, or put a fixing within 50mm of each end. A chamfered end reduces snagging.
Will it go round a curve or corner?
It bends around gentle curves. For tight external corners, mitre two lengths at 45° and fix both ends securely.
Does it come pre-drilled?
No. It is supplied plain so you can set the fixings to suit your structure.
Can I get a length other than 5m or 10m?
The 5m and 10m lengths are stocked. For longer runs, order several lengths and butt-join them, or contact us about a continuous length.
Delivery
Held in stock in the UK and sent the same working day on orders placed before the cut-off. Lengths are coiled loosely to avoid kinking.
Related products
- EPDM D Fender – 32mm x 22mm Hollow Profile – 5m or 10m Roll
- EPDM Hollow D Fender – 40mm x 25mm Impact Protection Profile
- Hollow TPE DD Fender – 20mm x 8mm Non-Marking – 25m Roll
Need help choosing a profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-IPRDF-24X16-5 |
|---|---|
| Weight | 3.53 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Hollow Rubber D Fender – 24mm x 16mm, 72 Shore A – 5m or 10m Length