
Rubber & FoamSKU IP-EPDMP-19.5X7.5-14
EPDM P Profile Seal – 19.5mm Tail x 7.5mm Bulb – Cut Lengths
Price shown updates with the option you pick.
A black solid-EPDM P-section seal with a 19.5mm wide flat tail and a 7.5mm hollow round bead. Bond or fix the tail to the frame and the bead stands 7.5mm proud; when the door, hatch or lid closes, the hollow bead squashes down to fill the gap and keep out rain, spray, dust and draughts. Sold as one continuous length from 14m up to a full 30m coil, held in stock.
At a glance
- P section: 19.5mm overall width x 7.5mm bead diameter
- 12mm free tail beyond the bead, 2.75mm thick at the tip, tapered for a neat low edge
- Hollow bead compresses easily on light doors and covers
- Solid (dense) EPDM, 65–75 IRHD (Shore A)
- Works from -40°C to +90°C; good UV, ozone and weather resistance
- Low 21% compression set (22 h at 70°C), so the bead keeps springing back
- 0.07 kg per metre; one unjoined length, 14m to 30m
Technical drawing

Specifications
| Property | Value | Test condition / method |
|---|---|---|
| Profile | P section, hollow round bead with flat tapered tail | — |
| Overall width | 19.5 mm | Nominal, maker's drawing |
| Bead diameter (height) | 7.5 mm | Nominal, maker's drawing |
| Free tail beyond bead | 12 mm | Nominal, maker's drawing |
| Tail thickness at tip | 2.75 mm | Nominal, maker's drawing |
| Hollow bore | ≈ 4.3 mm (bead wall ≈ 1.6 mm) | Scaled from the maker's drawing, not separately stated |
| Material | Solid (dense) EPDM rubber | — |
| Colour | Black | — |
| Hardness | 65–75 IRHD (Shore A) | Maker's datasheet |
| Tensile strength | 10 MPa | Maker's datasheet |
| Elongation at break | 500% | Maker's datasheet |
| Tear strength | 50 kN/m | Maker's datasheet |
| Compression set | 21% | 22 hours at 70°C |
| Ozone resistance | No cracks | 72 hours at 40°C, 22 pphm, extended |
| Heat ageing: hardness change | 0 IRHD | 70 hours at 70°C |
| Heat ageing: tensile change | +9% | 70 hours at 70°C |
| Heat ageing: elongation change | 0% | 70 hours at 70°C |
| Minimum service temperature | -40°C | Maker's stated limit |
| Maximum service temperature | +90°C | Maker's stated limit |
| Weight | 0.07 kg per metre | Maker's stated |
| Lengths | 14m to 29m in 1m steps, or a full 30m coil | One continuous length |
| Density | ≈ 1.2–1.4 g/cm³ | Typical for dense EPDM, not tested on this profile |
| Dimensional tolerance | About ±0.3–0.5 mm on these sizes | Typical for extruded rubber (ISO 3302-1 class E2), not tested on this profile |
Materials and compliance
Made from a dense EPDM (ethylene propylene diene monomer) rubber compound. EPDM is chosen for outdoor sealing because it shrugs off sunlight, ozone, rain and frost far better than natural rubber or PVC. It is not suitable for contact with petrol, diesel or mineral oils.
The maker does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire or other approvals for this profile, so we do not claim any. If you need a certified grade, ask us before ordering.
Typical uses
- Door, window and hatch seals on vans, trailers, horseboxes and transport bodies
- Marine deck lockers, hatches and enclosure lids
- Steel cabinet, kiosk and control-panel doors
- Access panels, covers and lids that need weatherproofing
- Light cushioning or edge trim where a soft round bead is wanted
How it seals

For a good seal the closed gap between the frame and the door should be smaller than the 7.5mm bead, typically around 4–5mm, so the bead is squeezed by roughly a third to a half. If the gap is 7mm or more, choose a larger P seal.
Which size do I need?
| Closed gap | Suggested P seal |
|---|---|
| About 3.5–5.5 mm, fixing face at least 20 mm | This EPDM P seal 19.5 x 7.5mm |
| About 5.5–8 mm, wider fixing face | EPDM P seal 26.5 x 11mm |
| About 6–9 mm, heavier doors | EPDM P seal 31.67 x 12.5mm |
How much do I need?
Measure the full perimeter of every opening and add about 5% for trimming. Example: four access doors each 1000 x 600mm = 4 x 3.2m = 12.8m, plus 5% ≈ 13.4m, so the 14m length does it in one piece. Prices work out from about £14.21 per metre on a 14m length down to about £10.10 per metre on a full 30m coil, so the 30m coil costs less than any length from 22m upwards.
Fitting tips
- Clean and degrease the frame (isopropyl alcohol is ideal) so the tail bonds properly.
- Fix through the flat tail only: contact adhesive, rivets, screws or staples. Never pierce the bead.
- Lay the seal in without stretching it, or it will creep back and open gaps at the ends.
- Put the joint at the top of the opening so water runs away from it.
- At corners, either bend round a radius of at least 25mm or mitre-cut and glue.
Frequently asked questions
How do I fit this P seal?
Bond the 19.5mm tail flat to the frame with a suitable rubber contact adhesive, or fix it with rivets, screws or staples through the tail. The bead faces the closing door.
What gap will it seal?
The bead stands 7.5mm proud. It works best where the closed gap is about 3.5–5.5mm, so the hollow bead is compressed by a third to a half.
Can it be used outdoors and on boats?
Yes. EPDM has excellent resistance to UV, ozone, rain, salt spray and frost; the maker's ozone test shows no cracking.
What temperatures can it take?
The maker states -40°C to +90°C for continuous service. Above 90°C choose a silicone P seal.
Is it oil or fuel resistant?
No. EPDM swells in petrol, diesel and mineral oils. For oily areas use a nitrile or neoprene seal.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt-join the ends with a cyanoacrylate (superglue) adhesive suitable for EPDM, ideally with a primer, or simply butt the ends tightly together at the top of the opening.
Is the bead hollow or solid?
Hollow, with a bore of about 4.3mm, so it closes with light force and follows slightly uneven surfaces.
Why is the 30m coil cheaper than some shorter lengths?
The 30m option is a full uncut coil with no cutting or rewinding, so it is priced lower per metre.
Need help choosing a seal? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMP-19.5X7.5-14 |
|---|---|
| Weight | 2.16 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM P Profile Seal – 19.5mm Tail x 7.5mm Bulb – Cut Lengths