
Rubber & FoamSKU IP-SGTS-13.5X30-08M
Self-Grip EPDM Top Seal – 13.5mm x 30mm – Sponge Tail, Fits 1.6-3mm Panels – 8m to 50m
Price shown updates with the option you pick.
A push-on top seal for 1.6mm to 3mm panel edges. A steel-reinforced solid EPDM grip clamps the edge with no glue, and a hollow sponge EPDM tail curls over one side of it so a door, lid, boot or hatch closes onto soft rubber. It is 30mm high and 13.5mm wide overall, black, and supplied as one continuous length from 8m to 49m at £17.61 per metre, or as a full 50m coil for £660.00 (£13.20 per metre). All prices include VAT.
At a glance
- 30mm high x 13.5mm wide overall; grip 14mm deep with a 4.5mm mouth before fitting
- Fits panel, flange and sheet edges 1.6mm to 3mm thick
- Full-length Fe50 steel carrier and internal gripping fingers: no adhesive, no fixings
- Hollow expanded EPDM tail stands about 16mm above the grip and folds down under light closing force
- EPDM resists weather and ozone and works from -40°C to +80°C
- Reproduction profile for boot aperture seal OEM 055-077-0002 (Aston Martin DB6)
- In stock in the UK; each length is one piece with no joins
Which length should I order?
Measure every edge the seal runs along, add them up and add about 5% for trimming and the joint. Choose that length in metres. If you need 38m or more, the 50m coil costs less than a cut length, so choose the coil and keep the spare.
Technical drawing

Specification
| Property | Value | Test method / note |
|---|---|---|
| Dimensions and fit | ||
| Overall height | 30mm | Bottom of grip to top of tail |
| Overall width | 13.5mm | Back face of grip to tail tip |
| Grip depth | 14mm | Height of the U-shaped grip section |
| Grip mouth | 4.5mm | Opening before fitting; fingers close it down |
| Tail height above grip | approx. 16mm | Calculated: 30mm − 14mm |
| Panel thickness it fits | 1.6mm to 3mm | Manufacturer's stated range |
| Dimensional tolerance | ISO 3302-1:2014 Class E2 | Extrusion tolerance class |
| Lengths | 8m to 49m in whole metres, or 50m full coil | One continuous piece |
| Colour | Black | – |
| Solid EPDM grip body | ||
| Hardness | 80 ±5 Shore A | ASTM D2240 (product page quotes 67° to 82°) |
| Tensile strength | 80 kg/cm² (about 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm | ASTM D624 |
| Compression set | 40% maximum | ASTM D395 Type B |
| Brittle point | -40°C | ASTM D746 |
| Air ageing, 70h at 70°C | Hardness +2°; tensile strength +15% | Change after ageing |
| Ozone resistance | Pass | ASTM D1149, 70h at 50°C, 50 pphm, 20% elongation |
| Sponge EPDM tail | ||
| Material | Expanded (sponge) EPDM | – |
| Density | 550 to 600 kg/m³, indicative | Datasheet prints the unit as g/cm³; 0.55 to 0.60 g/cm³ is meant |
| Tensile strength | 7 to 10 kg/cm² | ASTM D412 |
| Tear resistance | 0.6 to 0.8 kg/mm | ASTM D624 |
| Water absorption | 1.2% maximum | ASTM D1056, 22h at 23°C |
| Brittle point | -40°C | ASTM D746 |
| Ozone resistance | Pass | ASTM D1149, 70h at 50°C, 50 pphm, 50% elongation |
| Recommended compression | 30% to 40%; 40% maximum | Manufacturer guidance; never exceed 50% |
| Steel carrier | ||
| Grade | Fe50 | UNI 5961-67 |
| Tensile strength | 50 kg/mm² minimum | – |
| Hardness | 80 to 90 HRB | Rockwell B |
| Service | ||
| Operating temperature | -40°C to +80°C | Manufacturer's stated range |
Materials and compliance
The grip is solid EPDM over a full-length Fe50 steel carrier; the sealing tail is expanded EPDM. EPDM is chosen for outdoor doors and hatches because it shrugs off rain, UV and ozone. The manufacturer has not confirmed any food-contact, drinking-water, fire-performance, REACH or RoHS approval in writing for this profile, so we do not claim one. If you need a declaration for your project, ask us before ordering.
Typical uses
- Boot, bonnet and door aperture seals on classic and kit cars, including the Aston Martin DB6 boot (OEM 055-077-0002)
- Vans, buses, trains and plant cabs where a panel edge must also seal a closing door
- Marine lockers, deck hatches and service covers
- Electrical enclosures, control cabinets and machine-guard doors
- Garage doors, side windows and interior side panels
Fitting

- Check the edge is 1.6mm to 3mm thick, clean, dry and free of burrs, with at least 14mm of edge for the grip.
- Offer the seal up with the tail leaning towards the door, lid or hatch that closes onto it.
- Start mid-way along an edge, press on by hand, then tap fully home with a rubber mallet.
- Ease it round corners without stretching it, and butt the two ends tightly, ideally at the bottom of the opening.
- Close the door and check the tail is squeezed by roughly 30% to 40%, never more than half.
Questions
Do I need glue?
No. The steel carrier and the gripping fingers inside the U hold it on 1.6mm to 3mm panels. A bead of adhesive in the channel is only worth adding on a very smooth, painted edge that sees heavy vibration.
Which way does the tail face?
Towards the panel that closes onto it. The tail curls over one side of the grip, so the door, lid or hatch presses it down and the hollow core lets it fold rather than push back hard.
My panel is thinner than 1.6mm or thicker than 3mm. Will it fit?
Below 1.6mm the grip will be loose and above 3mm it will be hard to push on and may split. Measure the edge with a vernier and choose a top seal rated for that thickness; we can help.
Will it go round corners?
Yes. The steel carrier bends round normal door and hatch corners by hand. Ease it round slowly; on a very tight corner, a small V-cut in the back of the grip stops it puckering.
How do I cut and join it?
Cut through the steel carrier with heavy-duty side cutters or tin snips, then trim the sponge square with a sharp knife. Butt the ends tightly; a spot of cyanoacrylate (superglue) on the rubber faces makes a neat, sealed joint.
Is it suitable outdoors and in the cold?
Yes. EPDM passes the manufacturer's ozone test and is rated from -40°C to +80°C, so it suits vehicles, boats and outdoor enclosures all year round. It is not for oily or fuel-soaked areas.
Does it fit an Aston Martin DB6 boot?
The manufacturer makes this profile as a reproduction of DB6 boot aperture seal 055-077-0002. Compare the drawing with your old seal first, as restored cars vary.
Why is the 50m coil cheaper than 40m?
Full coils are priced lower per metre (£13.20 against £17.61 for cut lengths), so from 38m upwards the coil is the cheaper option.
Not sure which seal fits? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk with a photo of your edge.
Product details
| SKU | IP-SGTS-13.5X30-08M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip EPDM Top Seal – 13.5mm x 30mm – Sponge Tail, Fits 1.6-3mm Panels – 8m to 50m