
Rubber & FoamSKU IP-ESRD-20X21-20M
EPDM Sponge Rear Door Seal – 20mm x 21mm – 20m to 50m Lengths
Price shown updates with the option you pick.
A soft, closed-cell EPDM sponge rear door seal, 20mm wide by 21mm high, with a raised sealing fin, a rounded compression lobe and a 2mm clip channel in the base. The channel locates on the door's seal clips, so it fits the same way as the original strip and compresses against the body opening to keep out wind, rain and road dust. Each variant is one continuous length from 20m to 50m; the 50m full coil costs less than any cut length from 39m upwards.
At a glance
- Size: 20mm overall width x 21mm overall height, 2mm clip channel, 8mm lower lip
- Material: expanded (closed-cell) EPDM sponge, black, 40° Shore OO
- Fixing: clip-fitted through the 2mm channel; no adhesive needed
- Weathering: rated excellent for ozone, weather and UV resistance; flexible at -40°C
- Supplied as: one continuous length, 20m to 50m in 1m steps, or the full 50m coil
- In stock for same-day dispatch
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 20 mm | Manufacturer's drawing, nominal |
| Overall height | 21 mm | Manufacturer's drawing, nominal |
| Clip channel width | 2 mm | Manufacturer's drawing, nominal |
| Lower lip (base) length | 8 mm | Manufacturer's drawing, nominal |
| Upper fin dimension | 10 mm (as marked on the manufacturer's drawing) | Manufacturer's drawing, nominal |
| Dimensional tolerance | BS 3734 Class E3 (sponge sizes are approximate as the material compresses) | BS 3734-1 |
| Material | Expanded EPDM sponge (closed cell) | Manufacturer's data |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer |
| Density range | 0.5 – 0.9 g/cm³ | Manufacturer's data sheet |
| Water absorption | 5% maximum | Manufacturer's data sheet |
| Compression set | 25% maximum (data sheet, 24 h recovery); 50% (product page, 22 h) | Manufacturer's data; the two published figures differ, so use the worse value for design |
| Oven ageing, 7 days at 70°C | ±30% change | Manufacturer's data sheet |
| Low-temperature flexibility | Pass at -40°C | Manufacturer's data sheet |
| Ozone resistance | Excellent | Manufacturer's rating |
| Weather resistance | Excellent | Manufacturer's rating |
| UV light resistance | Excellent | Manufacturer's rating |
| Mould growth resistance | Very good | Manufacturer's rating |
| Upper service temperature | Approx. +100°C continuous (typical for EPDM sponge, not tested on this profile) | Generic material guidance |
| Tensile strength, elongation, tear | Not published for this sponge profile | - |
| Weight | 132 g per metre (data sheet rounds to 0.14 kg/m) | Manufacturer's data |
| Coil length | 50 m; cut lengths 20 m to 49 m | - |
| Price per metre (cut lengths) | £12.50 inc VAT (£12.495 exactly), e.g. 20m = £249.90 | - |
Materials and compliance
Expanded EPDM is a synthetic rubber with a closed-cell structure, so it does not wick water and recovers well after compression. It resists weathering, ozone and UV, steam, and dilute acids, alkalis and ketones, but is not suitable for continuous contact with petrol, mineral oils or greases. The manufacturer does not state any food-contact, potable-water or other third-party approvals for this profile, so none are claimed here.
Where it is used
- Rear door seals on small vans and estate cars, including replacement strips for the classic Mini Van and Clubman estate rear doors
- Clip-fitted door and hatch seals on trailers, horseboxes and kiosks
- Restoration projects where the original sponge seal has hardened or split
- Enclosure doors and access panels with seal clips or a 2mm retaining edge
How much do I need?
On a twin rear-door van the seal is fitted along the outer three sides of the left-hand door and all the way round the right-hand door. Add both runs together and round up to the next metre.
Worked example: doors 1.0m high x 0.6m wide. Left door: 1.0 + 0.6 + 1.0 = 2.6m. Right door: 1.0 + 0.6 + 1.0 + 0.6 = 3.2m. Total 5.8m per vehicle, so a 20m length does three vehicles with spare. If you need more than about 38m, the 50m coil is the cheaper option.
Fitting
- Remove the old seal and clips, and clean the door edge of residue and rust.
- Fit the seal at room temperature; cold sponge is stiffer and harder to ease round corners.
- Slide the 2mm channel onto the clips, starting at the bottom of the hinge side, with the fin facing outwards towards the body opening.
- Do not stretch the strip as you go. Ease it round corners and push it back slightly so it is never under tension, otherwise it will shrink back and leave gaps.
- Cut the end square with a sharp knife, leaving a few millimetres extra so the joint butts tightly.
Frequently asked questions
How does the seal attach to the door?
The 2mm channel in the base slides over the door's seal clips or a thin retaining edge, in the same way as the original strip. Clips are not included.
Is it the right size for my door?
Compare your old seal's cross-section with the drawing above: 20mm wide, 21mm high, a pointed fin on top and a 2mm slot in the base. If you are unsure, send us a photo of the cut end next to a ruler and we will confirm.
What can I use it for apart from van doors?
Any clip-fitted door, hatch or panel where a soft, compressible seal of around 20mm is needed, such as trailers, kiosks and equipment enclosures.
What is the material and how hard is it?
Closed-cell expanded EPDM sponge at 40° Shore OO, which is soft enough to close easily but springs back to seal.
What temperatures will it take?
The manufacturer confirms flexibility down to -40°C. EPDM sponge is typically used up to around +100°C, but that upper figure is generic for the material and has not been tested on this profile.
How do I cut and join it?
Cut with a sharp utility knife or scissors. For a continuous ring, butt the ends together and bond them with a cyanoacrylate rubber adhesive; on most doors a tight butt joint at the bottom corner is enough.
Is it sold per metre?
Each variant is one continuous piece from 20m to 49m, or the full 50m coil. We do not join shorter pieces to make up a length.
Can it be used outside all year?
Yes. It is rated excellent for weather, ozone and UV resistance, and absorbs no more than 5% water.
Need help matching a profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-ESRD-20X21-20M |
|---|---|
| Weight | 5.82 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Rear Door Seal – 20mm x 21mm – 20m to 50m Lengths