
Rubber & FoamSKU IP-EPDMU-6.7X15.5-8M
EPDM Square U Channel – 6.7mm x 15.5mm – Fits 3mm Panel – Black Rubber Edge Trim
Price shown updates with the option you pick.
A tall, solid black EPDM square U channel that pushes onto 3 mm sheet and panel edges and grips them deeply. It is 6.75 mm wide and 15.5 mm high, with a 3 mm slot that runs 13.5 mm deep and a solid 2 mm base over the edge. The walls are 1.875 mm thick at the base and taper slightly towards the mouth, so they hold the sheet firmly on both faces. You get a neat, square, cushioned finish over a sharp cut edge, and a hold that stays put on long runs. EPDM stands up well to weather and ozone, so it works indoors and out. Choose any length from 8 m to 29 m in one continuous piece, or a full 30 m coil. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet, panels and glazing 3 mm thick
- Size: 6.75 mm wide (sold as 6.7 mm) × 15.5 mm high; 3 × 13.5 mm slot; 1.875 mm walls; 2 mm base over the edge
- Material: solid EPDM rubber, 65–75° Shore A, black
- Strength: 10 MPa tensile, 500 % elongation, 50 kN/m tear (manufacturer data)
- Weathering: no cracks after the manufacturer's 72 h ozone test; compression set 21 %
- Lengths: 8 m to 29 m in 1 m steps, or a full 30 m coil. The full coil costs less than any length from 26 m up.
- Push-on fit with no tools. It cuts cleanly with a knife and is 100 % recyclable.
Technical drawing

All dimensions are in mm and nominal. The profile is sold as 6.7 × 15.5 mm; the manufacturer's measurements give the width as 6.75 mm, measured at the base. The 2 mm base is 15.5 mm minus the 13.5 mm slot depth. The 1.875 mm wall is the 6.75 mm width minus the 3 mm slot, split over two walls, and matches the manufacturer's stated 1.875 mm thickness. The outer faces taper slightly towards the mouth, as on the manufacturer's drawing; the width at the mouth is not specified. The drawing is not to scale.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Square U channel, parallel slot, outer faces taper slightly towards the mouth, flat base | Manufacturer drawing |
| Overall width (at base) | 6.75 mm (sold as 6.7 mm) | Manufacturer measurements and drawing |
| Overall height | 15.5 mm | Manufacturer measurements and drawing |
| Slot (channel) width | 3 mm | Manufacturer drawing and listing |
| Slot depth (grip depth) | 13.5 mm | Manufacturer drawing |
| Wall thickness | 1.875 mm each side, at the base | Manufacturer ("thickness 1.875 mm"); matches (6.75 − 3) ÷ 2 |
| Base thickness over the edge | 2.0 mm | Calculated: 15.5 − 13.5 mm |
| Panel thickness it fits | 3 mm | Manufacturer |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer datasheet |
| Colour | Black | Manufacturer |
| Hardness | 65–75° Shore A (website), 65–75 IRHD ±5 (datasheet) | Manufacturer data; method not stated |
| Tensile strength | 10.0 MPa | Manufacturer datasheet; method not stated |
| Elongation at break | 500 % | Manufacturer datasheet; method not stated |
| Tear strength | 50 kN/m | Manufacturer datasheet; method not stated |
| Compression set | 21 % | 22 h at 70 °C (manufacturer datasheet) |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm (manufacturer datasheet) |
| Heat ageing: change in tensile strength | +9 % | 70 h at 70 °C (manufacturer datasheet) |
| Heat ageing: change in elongation | 0 % | 70 h at 70 °C (manufacturer datasheet) |
| Working temperature range | Not stated for this profile. About −40 °C to +120 °C is typical for EPDM, not tested on this profile. | Typical for EPDM; ask us if you need a rated value |
| Weight | 0.1 kg per metre | Manufacturer |
| Density | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated for this profile; dimensions are nominal | Ask us if you need it |
| Supplied as | One continuous length, 8 m to 29 m, or a 30 m coil | Choose a length above |
Lengths and prices
| Length | Price inc VAT | Per metre | Approx. weight |
|---|---|---|---|
| 8 m | £166.32 | £20.79 | 0.80 kg |
| 9 m | £187.11 | £20.79 | 0.90 kg |
| 10 m | £207.90 | £20.79 | 1.00 kg |
| 11 m | £228.69 | £20.79 | 1.10 kg |
| 12 m | £249.48 | £20.79 | 1.20 kg |
| 13 m | £270.27 | £20.79 | 1.30 kg |
| 14 m | £291.06 | £20.79 | 1.40 kg |
| 15 m | £311.85 | £20.79 | 1.50 kg |
| 16 m | £332.64 | £20.79 | 1.60 kg |
| 17 m | £353.43 | £20.79 | 1.70 kg |
| 18 m | £374.22 | £20.79 | 1.80 kg |
| 19 m | £395.01 | £20.79 | 1.90 kg |
| 20 m | £415.80 | £20.79 | 2.00 kg |
| 21 m | £436.59 | £20.79 | 2.10 kg |
| 22 m | £457.38 | £20.79 | 2.20 kg |
| 23 m | £478.17 | £20.79 | 2.30 kg |
| 24 m | £498.96 | £20.79 | 2.40 kg |
| 25 m | £519.75 | £20.79 | 2.50 kg |
| 26 m | £540.54 | £20.79 | 2.60 kg |
| 27 m | £561.33 | £20.79 | 2.70 kg |
| 28 m | £582.12 | £20.79 | 2.80 kg |
| 29 m | £602.91 | £20.79 | 2.90 kg |
| 30 m full coil | £536.40 | £17.88 | 3.00 kg |
Cut lengths are £20.79 per metre. The 30 m full coil works out at £17.88 per metre and costs less than any cut length from 26 m upwards, so if you need 26 m or more, take the coil.
Materials and compliance
This profile is made from solid EPDM, a synthetic rubber known for its resistance to weather, ozone and UV. The manufacturer states that it is 100 % recyclable. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating, REACH, RoHS or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required. Ask us for a certified alternative.
How it fits

- Check the edge. Deburr, clean and dry it, and check the sheet is about 3 mm thick.
- Push on. Start at one end and press the channel down along the edge by hand. With a 13.5 mm deep slot, a little soapy water helps it slide fully home on long runs. You need no tools.
- Cut and join. Cut slightly over-length with a sharp knife or shears, then push the ends together into a tight butt joint.
- Bond if needed. Where there is vibration, or where you need a sealed fit (for example round an aluminium window channel), run a bead of polyurethane or silicone sealant into the slot before fitting.
Typical uses
- Edge protection on 3 mm sheet steel and aluminium, machine guards and enclosure panels
- Finishing the cut edges of 3 mm acrylic, polycarbonate, plywood or hardboard panels
- Knock protection on vending machines, cabinets, shelving and furniture
- Edging glass or glazing panels around 3 mm thick
- Safety edging on stairs, step plates and running boards where a thin edge is exposed
- Outdoor trailers, kiosks and equipment covers, where EPDM's weather resistance helps
FAQ
What thickness of panel does it fit?
It is made for 3 mm material. For slightly thinner sheet you can bond a thin rubber strip inside the slot to pack it out. For thicker material choose a channel with a wider slot. To make the finished edge wider, a neoprene strip can be bonded alongside it.
Why choose a 15.5 mm tall channel?
The extra height gives a 13.5 mm deep slot, so the channel grips much more of the edge than a shallow channel. It is less likely to peel off on long runs, curves or edges that get knocked, and it hides more of a rough or uneven cut. The 2 mm base also gives a thicker cushion over the edge itself.
How do I work out what length I need?
Measure the sheet thickness with a caliper, and the total run of edge in metres. Add about 5 % for cutting. Choose the next length up. The shortest length is 8 m. If you need 26 m or more, take the full 30 m coil, because it is cheaper.
Will it stay on without glue?
On a clean 3 mm edge the deep slot holds by grip alone for most static uses. On moving doors, vibrating machinery or outdoor parts, bond it with polyurethane or silicone sealant.
Can it be used outdoors?
Yes. EPDM is one of the most weather-resistant rubbers. In the manufacturer's ozone test (72 h at 40 °C, 25 pphm) it showed no cracks, and heat ageing at 70 °C left its elongation unchanged.
What temperatures can it take?
The manufacturer does not give a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, but that is a general figure for the material, not a tested rating for this part. If your application is near those limits, ask us first.
How do I cut and join it?
Cut it with a sharp knife, shears or a fine-tooth saw for a square end. Butt the ends tightly together. For a sealed joint, bond the ends with a flexible adhesive or sealant. To go round a tight corner, mitre the channel or notch the base slightly so it bends without lifting.
Is it oil resistant?
EPDM is not recommended for contact with mineral oils, petrol or diesel. For oily areas, ask us about a nitrile or neoprene channel.
Is it food safe or WRAS approved?
No approvals are stated for this profile, so it should not be used where food-contact or drinking-water certification is needed.
Is it in stock?
Yes. We hold it in stock and it is supplied as one continuous length cut to the size you choose, or as a full 30 m coil.
Complete your project
- EPDM Square U Channel – 6mm x 9.5mm – fits 3 mm panel (lower profile)
- EPDM Square U Channel – 6mm x 8mm – fits 3 mm panel
- EPDM Square U Channel – 6.5mm x 15.2mm – fits 3.5 mm panel
Need help choosing or fitting? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-EPDMU-6.7X15.5-8M |
|---|---|
| Weight | 1.76 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 6.7mm x 15.5mm – Fits 3mm Panel – Black Rubber Edge Trim