
Rubber & FoamSKU IP-EPDMU-4.5X9-18
EPDM U Channel – 4.5mm x 9mm – Black Rubber Edge Trim
Price shown updates with the option you pick.
This solid black EPDM rubber U channel, 4.5mm wide by 9mm high, pushes onto 1.6mm panel edges to cover sharp metal, glass, plastic or timber and absorb knocks. It is sold by the continuous length, from 18m up to a full 30m coil, and is easy to cut to size on site.
At a glance
- Solid EPDM rubber, 65-75° Shore A
- Rounded profile, 4.5mm wide x 9mm high
- 2mm tapered inner channel grips 1.6mm panels
- Very good weathering, heat and cold resistance
- Good flex fatigue and abrasion resistance
- Light at about 0.04kg per metre and fully recyclable
Typical uses
- Finishing raw sheet metal edges on guards, cabinets and enclosures
- Edging glass and plastic panels
- Protecting door and wooden panel edges from knocks
- Safety edging on stairs, running boards and vending machines
- Covering sharp edges on furniture and shop fittings
Which one do I need?
| Profile (width x height) | Panel thickness | Best for |
|---|---|---|
| 4.5mm x 9mm (this item) | 1.6mm | Compact, rounded trim for thin sheet edges |
| 5.6mm x 19mm | 1.6mm | Deep 19mm sides that cover more of the panel face |
| 5.7mm x 17mm | 1.5mm to 2.5mm | Panels that vary slightly in thickness |
| 5.5mm x 8.5mm | 3mm | Thicker sheet, board and glazing edges |
Measure your panel with a vernier or ruler first: the channel must match the panel thickness to grip without adhesive.
Technical drawing
Specification
| Material | Solid EPDM (ethylene propylene diene monomer) |
| Colour | Black |
| Overall size | 4.5mm wide x 9mm high |
| Channel width | 2mm |
| Wall thickness | 1.25mm |
| To fit panel | 1.6mm |
| Hardness | 65-75° Shore A |
| Tensile strength | 10 MPa |
| Elongation at break | 500% |
| Tear strength | 50 kN/m |
| Weight | 0.04kg per metre |
| Unit of sale | One continuous length, 18m to 30m (full coil) |
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Example: four guard panels, each 1200mm x 800mm, edged on all sides need 4 x 4.0m = 16m; adding 5% gives 16.8m, so the 18m length (the shortest available) covers the job in one piece.
Fitting tips
- Clean and degrease the panel edge before fitting.
- Cut square with sharp shears or a craft knife so butt joints close neatly.
- Start at a corner or out of sight and press the channel on progressively with your thumb; do not stretch it.
- For a permanent or watertight fix, bed it in polyurethane or silicone sealant.
- On a slightly thinner panel, bond a thin strip inside the channel to take up the gap.
Complete your project
- EPDM U channel 5.6mm x 19mm for 1.6mm panels
- EPDM U channel 5.5mm x 8.5mm for 3mm panels
- EPDM U channel 5mm x 12.5mm round profile
- EPDM U channel 4.8mm x 9.6mm
- EPDM U channel 5.4mm x 9.7mm in cut lengths
Questions
Can it be used outdoors?
Yes. EPDM resists weathering, heat and cold well, so it suits external panels and doors.
Will it fit a 2mm panel?
It is made for 1.6mm panels. A 2mm panel would stretch the channel and loosen the grip, so choose a profile made for the thickness you have.
Do I need adhesive?
Usually not: the tapered channel grips on its own. Use polyurethane or silicone sealant where you need a permanent or sealed fix.
How is the length supplied?
As one continuous piece of the length you choose, from 18m up to a full 30m coil.
How do I cut it?
Sharp shears, secateurs or a craft knife give a clean, square cut.
Need help choosing the right edge trim? Contact our team.
Product details
| SKU | IP-EPDMU-4.5X9-18 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM U Channel – 4.5mm x 9mm – Black Rubber Edge Trim