
Rubber & FoamSKU IP-EPDMG-15X12.5-18
EPDM Weatherstrip Glazing Seal 15mm x 12.5mm – for 3mm Glass & 0.8–1.6mm Panels – 18m to 30m
Price shown updates with the option you pick.
This EPDM weatherstrip glazing seal, 15mm x 12.5mm, is a black solid-rubber window gasket that holds a pane of glass, acrylic or polycarbonate up to 3mm thick in a 0.8mm to 1.6mm sheet-metal panel and keeps the joint air and watertight. A 7mm x 6mm filler strip pushed into the top groove expands the seal and clamps both edges. It is cut as one continuous length from 18m to 30m, held in stock and dispatched from the UK.
At a glance
- 15mm wide x 12.5mm high solid EPDM glazing gasket, black
- Glass slot 3mm wide x 4.5mm deep – takes glazing up to 3mm
- Panel slot 1.6mm wide x 4.5mm deep – grips 0.8mm to 1.6mm sheet
- 6mm clearance between the edge of the glass and the edge of the panel cut-out
- Bends round corners down to a 30mm radius without kinking
- Hardness 65–75 IRHD; works from -40°C to +90°C
- Locked with a 7mm x 6mm filler strip (sold separately)
Typical uses
- Vision panels of thin acrylic or glass in machine guards, control cabinets and enclosures
- Windows in light-gauge vehicle bodies, trailers, horseboxes, kiosks and plant cabs
- Replacement weatherstrip glazing rubber on caravans, boats and classic vehicles with thin panels
- Glazing polycarbonate inspection windows into sheet-steel doors
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Weatherstrip (H-type) glazing seal with filler-strip groove | Supplier drawing |
| Overall width | 15.0 mm | Supplier drawing, nominal |
| Overall height | 12.5 mm | Supplier drawing, nominal |
| Glass slot width | 3.0 mm (glazing up to 3 mm) | Supplier drawing |
| Glass slot depth | 4.5 mm | Supplier drawing |
| Panel slot width | 1.6 mm (fits 0.8 – 1.6 mm panel) | Supplier drawing |
| Panel slot depth | 4.5 mm | Supplier drawing |
| Glass-to-panel clearance | 6 mm | Supplier data |
| Filler strip | 7 mm x 6 mm (sold separately) | Supplier data |
| Minimum bend radius | 30 mm | Supplier datasheet |
| Material | Solid EPDM (ethylene propylene diene monomer) | Supplier datasheet |
| Colour | Black | – |
| Hardness | 65 – 75 IRHD | IRHD scale, supplier datasheet (method not stated) |
| Tensile strength | 10 MPa | Supplier datasheet (method not stated) |
| Elongation at break | 500 % | Supplier datasheet (method not stated) |
| Tear strength | 50 kN/m | Supplier datasheet (method not stated) |
| Compression set | 21 % | 22 hours at 70 °C, supplier datasheet |
| Maximum temperature | +90 °C | Supplier data |
| Minimum temperature | -40 °C | Supplier data |
| Weight | 0.13 kg per metre (approx. 3.9 kg for 30 m) | Supplier data |
| Density, cross-section tolerance | Not published for this profile – ask us if you need them | – |
| Supplied as | One continuous length, 18 m to 30 m (30 m = full coil) | – |
Materials and compliance
Made from solid black EPDM rubber. EPDM is chosen for outdoor glazing because it resists sunlight, ozone, rain and ageing and stays flexible in frost (typical for EPDM, not tested on this profile). Our supplier states no food-contact, fire-rating, WRAS, REACH or RoHS approvals for this profile, so we do not claim any. If your project needs a certificate of conformity, contact us before ordering.
Which seal do I need?
| Seal size | Glass thickness | Panel thickness |
|---|---|---|
| 15mm x 12.5mm (this seal) | Up to 3mm | 0.8mm – 1.6mm |
| 20mm x 17mm | 4.75mm | 0.8mm – 1.6mm |
| 15mm x 13.5mm | Similar outer size – see that listing for its slot sizes | |
Measure the glass and the panel edge with a vernier before ordering. A slot that is too wide will not grip; one that is too narrow will stop the filler strip closing.
How much do I need?
Add up the perimeter of every opening – (width + height) x 2 – and allow about 25mm extra per window for the butt joint. Six windows of 1000mm x 500mm each need 6 x 3.025m = 18.15m, so choose the 19m length. Order the same length of filler strip. The 30m full coil is the best value per metre (£9.50/m against £10.69/m for cut lengths).
Fitting guide
- Remove any old seal and clean and de-burr the panel edge; a sharp edge will cut the rubber over time.
- Push the panel slot onto the aperture all the way round, pressing it tight into the corners (minimum 30mm corner radius).
- Cut the seal about 25mm longer than the perimeter with a square cut, so the ends butt together under slight compression. Put the joint at the top of the frame.
- For a fully watertight result, run a small bead of silicone sealant in the panel slot and the glass slot.
- Seat the glass from the bottom upwards, working the outer lip over the edge with a fitting tool.
- Brush a little lubricant (soapy water) into the groove and feed the 7mm x 6mm filler strip in with a filler-strip tool, starting at the bottom. Do not stretch the filler strip – it will shrink back later.
- Cut the filler strip a few millimetres long and push the end in to make a tight butt joint.
Complete your project
- Glazing weatherstrip filler strip 7mm x 6mm
- Weather/glazing strip fitting tool for rubber filler strips
- EPDM weatherstrip glazing seal 20mm x 17mm (for 4.75mm glass)
Frequently asked questions
Does the glazing seal come with the filler strip?
No. The 7mm x 6mm filler strip is sold separately and is needed to lock the seal onto the glass and the panel. Order the same length as the seal.
What thickness of glass and panel does it fit?
Glass, acrylic or polycarbonate up to 3mm in one slot, and sheet steel or aluminium from 0.8mm to 1.6mm in the other. For 4.75mm glass choose the 20mm x 17mm seal.
How big a hole do I cut in the panel?
The glass sits 6mm clear of the panel edge all round, so make the panel aperture 12mm larger than the glass in each direction (e.g. a 500mm x 300mm pane needs a 512mm x 312mm cut-out).
How tight a corner will it go round?
The minimum bend radius is 30mm. Use a corner radius of 30mm or more on the panel and the glass so the seal does not kink or lift.
How do I cut and join it?
Cut with a sharp knife or rubber shears, square across. Make a single butt joint at the top of the frame, cutting the seal about 25mm over length so the ends press together; a dab of silicone or rubber adhesive on the faces seals it fully.
Is it suitable for outdoor use and what temperatures does it take?
Yes. Solid EPDM resists UV, ozone and weather, and this profile is rated from -40°C to +90°C.
Will I get one piece or several shorter lengths?
Always one continuous piece of the length you select, so you can run it round several openings and cut only where you need to.
Can I use it for acrylic or polycarbonate?
Yes – any rigid glazing sheet up to 3mm thick. Plastic sheet expands more with heat than glass, so leave the full 6mm clearance on every side.
Need help choosing a glazing seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-EPDMG-15X12.5-18 |
|---|---|
| Weight | 5.82 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Weatherstrip Glazing Seal 15mm x 12.5mm – for 3mm Glass & 0.8–1.6mm Panels – 18m to 30m