Rubber & FoamSKU IP-SPEX-20-STD
Food Contact Silicone P Extrusion – 20mm x 10mm, Ø10mm Hollow Bead, 3mm Flange – Grey 60 Shore A – 25m Coil
A food contact silicone P seal for hygienic doors, hatches and lids. The profile is 20 mm wide overall. A hollow Ø10 mm bead squeezes shut against the door. A flat 3 mm thick flange gives you a 10 mm strip beside the bead to bond or clamp to the frame. It is made from grey 60 Shore A silicone to FDA 21 CFR 177.2600 and EC 1935/2004, works from −40 °C to +200 °C, and comes as one continuous 25 m coil. It is held in stock in the UK for same-day dispatch.
At a glance
- Size: 20 mm overall width × 10 mm height. Ø10 mm hollow bead, 3 mm flange.
- Food contact: the maker states FDA 21 CFR 177.2600 and EC 1935/2004 compliance. The silicone is non-toxic, non-leaching and pyrogen-free.
- Temperature: −40 °C to +200 °C in service, so it suits ovens, provers, steam cabinets and chillers.
- Seals a 6–8 mm gap: the hollow bead compresses easily and springs back for thousands of door cycles.
- Grey, non-marking: it will not stain stainless steel, glass or painted panels.
- 25 m continuous coil: enough for several door frames, with no joins in the run.
Technical drawing
![]()
The bore (≈ Ø4.5 mm) and bead wall (≈ 2.75 mm) are scaled from the maker's section drawing. All other sizes are stated nominal values.
Specification
| Property | Value | Method / basis |
|---|---|---|
| Profile type | P section (hollow round bead with a flat flange) | Maker's section drawing |
| Overall width | 20 mm | Nominal, ISO 3302-1 class E2 |
| Overall height (bead diameter) | 10 mm (Ø10 mm bead) | Nominal, ISO 3302-1 class E2 |
| Flange thickness | 3 mm | Nominal, ISO 3302-1 class E2 |
| Free flange beyond the bead | 10 mm | Derived: 20 mm overall − Ø10 mm bead |
| Bore / bead wall | ≈ Ø4.5 mm / ≈ 2.75 mm | Scaled from the maker's drawing, not stated |
| Length | 25 m continuous coil | Cut length tolerance ISO 3302-1 class L2 |
| Material | Silicone rubber (VMQ), food contact grade | Maker's data |
| Colour | Grey | Maker's data |
| Hardness | 60° Shore A | Shore A durometer |
| Service temperature | −40 °C to +200 °C | Maker's product rating |
| Compound temperature range | −65 °C to +200 °C | Maker's compound datasheet |
| Density | 1.15 g/cm³ | Maker's datasheet, 61 Shore A grade |
| Elongation at break | 440 % | Maker's datasheet, 61 Shore A grade |
| Tear strength | 11 N/mm | Maker's datasheet, 61 Shore A grade |
| Compression set | 31 % | 22 h at 175 °C, maker's datasheet, 61 Shore A grade |
| Tensile strength | Not stated by the maker for this compound | Ask us if you need a certificate |
| Dimensional tolerance | ISO 3302-1 E2 (section) / L2 (length) | ISO 3302-1 |
| Approx. weight | ≈ 0.11 kg per metre, ≈ 2.8 kg per coil | Calculated from section area × 1.15 g/cm³ |
| Part number | IP-SPEX-20-STD | Industrial Polymers |
Materials and compliance
- FDA 21 CFR 177.2600: the maker states compliance for rubber articles in repeated contact with food.
- EC 1935/2004: the maker states compliance with the EU framework regulation for food contact materials.
- The maker states the seal is made in a clean environment from FDA-approved silicone and is non-toxic, non-leaching and pyrogen-free. It will not taint or flavour food.
- Silicone has very good weathering resistance and is waterproof. Its oil resistance is only fair, so do not use it where it stays wet with mineral oils or fuels.
Only the approvals above are claimed for this product. We do not claim WRAS, REACH or RoHS approval for this profile.
How it fits
Fix the flat flange to the frame and leave the bead facing the door. When the door closes, the hollow bead flattens by about a third and seals the gap. For best results the closed gap should be about 6–8 mm. A smaller gap crushes the bead, which makes the door hard to latch. A gap of 10 mm or more will not seal.
- Bonded: degrease both surfaces, then run a thin bead of food-safe silicone adhesive along the flange.
- Clamped: trap the 10 mm free flange under a stainless retaining strip or a folded lip on the frame.
- Lay it in without stretching. Silicone that is stretched while fitting pulls back over time and leaves gaps at the corners.
- At corners, cut a V notch in the flange so the bead follows the bend without kinking.
Typical uses
- Doors and hatches on food processing machines and hygienic cabinets
- Covers and lids on hoppers, mixing tanks and vessels
- Door seals on commercial ovens, provers, steamers and drying cabinets (up to 200 °C)
- Glass panel doors on display cabinets and inspection windows
- Enclosures for pharmaceutical, laboratory and electrical equipment
Which P seal do I need?
| Profile | Best for |
|---|---|
| Food contact silicone P 20 × 10 mm (this item) | Gaps of about 6–8 mm on food and pharma equipment up to 200 °C |
| Silicone P 16 × 5 mm | Small gaps of about 3–4 mm |
| Food contact silicone P 25 × 12 mm | Slightly larger gaps, about 8–10 mm |
| High-temperature silicone P 20 × 8 mm | A similar size for ovens running hotter than 200 °C |
Frequently asked questions
What gap does the 20 × 10 mm P seal fill?
Aim for a closed gap of about 6–8 mm. That flattens the 10 mm bead by 20–40 %, which seals well and still lets the door latch easily. If your gap is 3–4 mm, choose the 16 × 5 mm profile. If it is 8–10 mm, choose the 25 × 12 mm.
Is it safe for direct contact with food?
Yes. The maker states the silicone complies with FDA 21 CFR 177.2600 and EC 1935/2004, and that it is non-toxic, non-leaching and pyrogen-free. It will not taint food.
What temperatures can it take?
The seal is rated from −40 °C to +200 °C in service, so it suits freezers and chillers as well as ovens and provers. Above 200 °C, use our high-temperature silicone P extrusions.
How do I fix it in place?
Bond the 3 mm flange with a food-safe silicone adhesive, or clamp the 10 mm free flange under a retaining strip. Make sure the surface is clean, dry and free of grease before you fit it.
How do I cut and join it?
Cut it square with a sharp knife or shears. For a continuous loop, butt the two ends and bond them with silicone adhesive. At corners, notch the flange so that the bead turns without kinking.
Can it be used outdoors or washed down?
Yes. Silicone resists UV, weathering, water and steam, and it stands up to normal hygienic wash-down. Keep it away from long soaking in mineral oils or fuels, because its oil resistance is only fair.
How long is the coil, and can I buy a shorter length?
Each coil is one continuous 25 m length. That is enough to go round about six 1 m × 1 m door frames. Contact us if you need a different length.
Is it in stock?
Yes. We hold it in stock in the UK, and orders placed before the cut-off go out the same day.
Need a certificate of conformity or help choosing a size? Contact our team on +44 1282 277786 or at sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SPEX-20-STD |
|---|---|
| Weight | 6.61 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Food Contact Silicone P Extrusion – 20mm x 10mm, Ø10mm Hollow Bead, 3mm Flange – Grey 60 Shore A – 25m Coil