
Rubber & FoamSKU IP-HDCP-585X75-3CH
Heavy-Duty Cable Protector – 3-Channel Hi-Vis – 0.9m Unit
This heavy-duty 3 channel cable protector is a 585mm x 75mm interlocking ramp that carries up to three cables or hoses safely across roads, yards and site access routes, with vehicles up to 40 tonnes driving over the top. Sold individually as one 0.9m unit; join as many as you need for a continuous run.
At a glance
- Three enclosed channels, each 65mm wide x 58mm high
- 585mm wide x 75mm high x 900mm long per unit, 23.5kg
- Rated for vehicle loads up to 40 tonnes at walking pace (5mph)
- High-visibility yellow hinged PVC lid for a clear trip and traffic warning
- Black natural rubber / SBR body, 85 Shore A, -45°C to +60°C
- Male and female connectors build a cable ramp of any length
Typical uses
- Temporary power, water and data runs across construction site haul roads
- Generator and distribution cables at outdoor events and festivals
- Yard and loading-bay crossings where forklifts and HGVs pass over cables
- Roadworks and pavement crossings, doubling as a speed-calming hump
- Film, broadcast and utility crews needing quick hose and cable protection
Which one do I need?
| Need | Best choice |
|---|---|
| Up to three cables or hoses up to 65mm wide, vehicle traffic | This 3 channel heavy-duty protector |
| Four or five separate runs, vehicle traffic | 5 channel lidded cable protector |
| One or two runs, lighter traffic | 2 channel hose and cable protector |
| Walkways and pedestrian areas only | A low-profile pedestrian ramp (lower trip height) |
Technical drawing
Specification
| Unit of sale | One 0.9m unit |
| Overall size | 585mm wide x 75mm high x 900mm long |
| Channels | 3, each 65mm wide x 58mm high |
| Body material | Natural rubber / SBR blend |
| Lid | Hinged PVC, high-visibility yellow |
| Hardness | 85 ±5 Shore A |
| Load rating | Up to 40 tonnes |
| Maximum vehicle speed | 5mph |
| Operating temperature | -45°C to +60°C |
| Weight | 23.5kg per unit |
| Connection | Interlocking male / female ends |
How much do I need?
Measure the width of the road or walkway the cables cross and divide by 0.9m, rounding up. A 6m wide site haul road needs 6 / 0.9 = 6.7, so order 7 units. Allow one extra unit if the cable run enters the crossing at an angle.
Fitting tips
- Lay on firm, level ground swept clear of stones so the base sits flat under load.
- Open the lid, lay each cable flat in its own channel without twists, then close the lid fully before traffic passes.
- Push the connectors fully home between units so the ramp cannot separate under wheels.
- Keep traffic to walking pace and avoid braking or turning on the ramp.
Complete your project
- 5 Channel Lidded Cable Protector
- 2 Channel Hose and Cable Protector
- Cable & Hose Protector Ramp – 290mm x 295mm x 118mm
Questions
What size cables fit this 3 channel cable protector?
Each channel is 65mm wide and 58mm high, so it takes single cables or hoses up to about 58mm diameter, or several smaller cables laid flat side by side.
Can lorries drive over it?
Yes. It is rated for vehicle loads up to 40 tonnes at a maximum of 5mph, so HGVs, plant and forklifts can cross at walking pace.
How do I make a longer cable ramp?
Each 0.9m unit has a male and a female connector, so units clip end to end to cover any width of road or yard.
Can it be left outside in winter?
Yes. The rubber body and PVC lid are rated for -45°C to +60°C and suit permanent outdoor use as well as temporary sites.
Need help choosing cable protection? Contact our team for advice.
Product details
| SKU | IP-HDCP-585X75-3CH |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Heavy-Duty Cable Protector – 3-Channel Hi-Vis – 0.9m Unit