
Rubber & FoamSKU IP-CRSS-10X3-10M
Neoprene Sponge Strip – 10mm x 3mm, Self-Adhesive, Closed Cell – 10m Length
A thin, black closed-cell neoprene sponge strip, 10mm wide x 3mm thick, with a pressure-sensitive adhesive layer on its 10mm face. Peel back the liner, press it onto a clean flange, lid or frame, and it seals against air, dust and water once it is squeezed by just 15–20%. That makes it a good choice where a cover or panel closes to a gap of roughly 2.4–2.55mm and only light closing pressure is available. Supplied as one continuous 10m length, black, from UK stock.
At a glance
- Size: 10mm wide x 3mm thick, flat rectangular section; adhesive on the 10mm face
- Seals at 15–20% compression, which means a closed gap of about 2.4–2.55mm
- Closed-cell neoprene (CR) sponge: it does not soak up water (under 5% by volume) and resists oil, UV and ozone
- Soft: 40–45 Shore OO, density 110–130 kg/m³, so covers close without extra force
- Temperature: −30°C to +90°C working range
- Self-extinguishing: flame resistance tested to FMVSS 302 and UL94 HF-1
- Value: £31.11 inc VAT per 10m length, which is about £3.11 per metre
Typical uses
- Lids and covers on electrical, control and instrument enclosures
- Inspection hatches, access panels and equipment housings
- Vehicle, caravan and marine door, window and locker seals with small gaps
- Anti-rattle and vibration pads between metal, glass and plastic panels
- Thin sound and thermal insulating strips, and energy-absorbing spacers
Technical drawing

Nominal dimensions in mm, free state before compression. The 3mm thickness is the sponge alone; the adhesive and liner sit under the 10mm face.
How it seals

Stick the 10mm face to the flange (or to the cover) so the strip lies flat. When the cover closes, the closed-cell sponge is squeezed and fills the gap. Because the cells are sealed, gas and liquid cannot pass through the strip itself; 15–20% squeeze (3mm down to about 2.4–2.55mm) is enough for an airtight seal.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Size and form | ||
| Profile | Flat rectangular strip, self-adhesive one side | – |
| Width | 10 mm | Nominal, manufacturer drawing |
| Thickness (sponge, excluding adhesive) | 3 mm | Nominal, manufacturer drawing |
| Adhesive face | The 10 mm (wide) face, with peel-off liner | Manufacturer data |
| Length supplied | 10 m, one continuous piece | – |
| Weight | 0.01 kg per metre (about 0.1 kg per 10 m) | Manufacturer data |
| Colour | Black | – |
| Dimensional tolerance | Not published for this product. Typical for cut neoprene sponge strip about ±0.5 mm on thickness (typical for neoprene sponge, not tested on this profile) | – |
| Material | ||
| Composition | Neoprene (polychloroprene, CR) sponge | Manufacturer data sheet |
| Cell structure | Closed cell | Manufacturer data |
| Density | 110–130 kg/m³ | Manufacturer data sheet |
| Hardness | 40–45 Shore OO | Shore OO durometer (manufacturer data sheet) |
| Mechanical | ||
| Tensile strength | 7.4 kg/cm² (≈ 0.73 MPa) | Manufacturer data sheet |
| Elongation at break | Over 200% | Manufacturer data sheet |
| Compressive strength at 25% deflection | 40 kPa (the supplier's product page also lists 55–85 kPa) | Manufacturer data sheet |
| Compression needed to seal | 15–20% | Manufacturer data |
| Tear strength | Not published for this product | – |
| Compression set | Not published for this product | – |
| Environmental | ||
| Working temperature | −30°C to +90°C (the data sheet gives −26°C as the lower figure; design to −26°C for continuous cold use) | Manufacturer data |
| Water absorption | Under 5% by volume | Manufacturer data sheet |
| Oil, UV and ozone | Very good oil resistance; good UV and ozone resistance | Manufacturer data |
| Flame resistance | Self-extinguishing | FMVSS 302 and UL94 HF-1 (manufacturer data sheet) |
| Blowing agents | CFC and HCFC free | Manufacturer data sheet |
Materials and compliance
- Flame resistance: the manufacturer states the material is self-extinguishing to FMVSS 302 (US motor vehicle interior flammability) and UL94 HF-1 (foamed plastics).
- Environmental: manufactured CFC and HCFC free.
- Not stated: the manufacturer makes no food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH or RoHS statement for this product, so do not use it where those approvals are required. Ask us if you need a food-safe or potable-water strip.
Fitting tips
- Check the gap. Close the cover and measure the gap. This strip suits about 2.4–2.55mm; for larger gaps choose a thicker strip.
- Clean the surface. Degrease with isopropyl alcohol and let it dry. The landing needs to be at least 10mm wide.
- Peel as you go. Lift a short length of liner at a time and press the strip down firmly across its full width.
- Don't stretch it. Lay the sponge in relaxed; stretched foam shrinks back and opens gaps at the ends.
- Cut and join. Cut square with a sharp knife and butt the ends tightly; at corners, mitre or butt-joint rather than folding.
FAQ
Is the price for one metre or the whole length?
The whole length. One unit is a single continuous 10m strip, about £3.11 per metre. Order 2 and you get two separate 10m strips.
What gap will it seal?
It needs to be squeezed by 15–20%, so it seals a closed gap of about 2.4–2.55mm. If the cover closes tighter than about 2mm it will be hard to shut; if the gap is over 2.6mm the strip may not touch all the way along.
Which side is sticky?
The wide 10mm face. It carries a pressure-sensitive adhesive under a peel-off liner, so the strip stands 3mm proud of the surface.
Will it stick to rough or painted surfaces?
Yes. The adhesive bonds to rough and smooth surfaces, including painted metal, glass and most rigid plastics, provided they are clean, dry and grease-free. Very low-energy plastics such as polythene and polypropylene may need a primer.
Is it waterproof and suitable outdoors?
Yes. It is a closed-cell sponge, so water and air cannot pass through it, and neoprene has good UV and ozone resistance for outdoor, automotive and marine use.
What temperatures can it handle?
The working range is −30°C to +90°C. The data sheet gives −26°C as the lower figure, so for continuous cold service treat −26°C as the limit.
Is it oil resistant?
Yes. Neoprene has very good resistance to oils and greases, which is why it is chosen over EPDM sponge for machinery and vehicle use.
How do I cut and join it?
Use a sharp knife or scissors and cut square. Butt the ends tightly together at joins; for a fully continuous seal, put a small dab of contact adhesive on the cut faces.
Is it food-safe or WRAS approved?
No food-contact or WRAS approval is stated for this product. Contact us and we can suggest a silicone alternative.
Delivery and help
Held in stock and dispatched from our UK warehouse. Trade and bulk orders are welcome. Not sure which thickness you need? Send us your gap measurement at sales@industrial-polymers.co.uk or call +44 1282 277786.
Product details
| SKU | IP-CRSS-10X3-10M |
|---|---|
| Weight | 0.33 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Neoprene Sponge Strip – 10mm x 3mm, Self-Adhesive, Closed Cell – 10m Length