
Rubber & FoamSKU IP-NUC-4.5X8.5-15
Neoprene Square U Channel – 4.5mm x 8.5mm – Black Rubber Edge Trim
Price shown updates with the option you pick.
A solid black neoprene (CR) square U channel that pushes onto 1.5 mm sheet and panel edges. It is 4.5 mm wide and 8.5 mm high. The 1.5 mm slot is 6.5 mm deep and widens slightly towards the base, so the lips grip both faces of the sheet at the mouth. The square, tapered body leaves a neat, flat-topped edge that takes knocks and covers sharp cut metal. Choose any length from 15 m to 30 m in one continuous piece. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet, panels and glazing 1.5 mm thick
- Size: 4.5 mm wide × 8.5 mm high, with a 2.0 mm solid base over the edge
- Material: solid neoprene (polychloroprene, CR), 65–75 hardness, black
- Working temperature: −20 °C to +90 °C
- Strength: 5 MPa tensile, 400 % elongation, 17 kN/m tear (manufacturer data)
- Lengths: 15 m to 29 m in 1 m steps, or a full 30 m coil. A full coil costs less than 26 to 29 m.
- Push-on fit with no tools. It cuts cleanly with a knife and is 100 % recyclable.
Technical drawing

All dimensions are in mm and nominal. The 2.0 mm base is the 8.5 mm height minus the 6.5 mm slot depth. The drawing is not to scale.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Square U channel with tapered walls | Manufacturer drawing |
| Overall width | 4.5 mm (at the base) | Manufacturer drawing |
| Overall height | 8.5 mm | Manufacturer drawing |
| Slot (channel) width | 1.5 mm at the mouth | Manufacturer drawing |
| Slot depth | 6.5 mm | Manufacturer drawing |
| Base thickness over the edge | 2.0 mm | Calculated: 8.5 − 6.5 mm |
| Panel thickness it fits | 1.5 mm | Manufacturer |
| Material | Solid neoprene, polychloroprene (CR) | Manufacturer datasheet |
| Colour | Black | Manufacturer |
| Hardness | 65–75° Shore A (website), 65–75 IRHD ±5 (datasheet) | Manufacturer data; method not stated |
| Tensile strength | 5.0 MPa | Manufacturer datasheet; method not stated |
| Elongation at break | 400 % | Manufacturer datasheet; method not stated |
| Tear strength | 17 kN/m | Manufacturer datasheet; method not stated |
| Compression set | 70 % | 22 h at 70 °C (manufacturer datasheet) |
| Ozone resistance | Some cracks | 72 h at 40 °C, 25 pphm (manufacturer datasheet) |
| Heat ageing: change in hardness | +7 points | 70 h at 70 °C (manufacturer datasheet) |
| Heat ageing: change in tensile strength | +15 % | 70 h at 70 °C (manufacturer datasheet) |
| Heat ageing: change in elongation | −17 % | 70 h at 70 °C (manufacturer datasheet) |
| Working temperature range | −20 °C to +90 °C | Manufacturer datasheet |
| Weight | 0.05 kg per metre | Manufacturer |
| Density | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated for this profile; dimensions are nominal | Ask us if you need it |
| Supplied as | One continuous length, 15 m to 30 m | Choose a length above |
Lengths and prices
| Length | Price inc VAT | Per metre | Approx. weight |
|---|---|---|---|
| 15 m | £197.52 | £13.17 | 0.75 kg |
| 16 m | £210.66 | £13.17 | 0.80 kg |
| 17 m | £223.83 | £13.17 | 0.85 kg |
| 18 m | £237.00 | £13.17 | 0.90 kg |
| 19 m | £250.17 | £13.17 | 0.95 kg |
| 20 m | £263.34 | £13.17 | 1.00 kg |
| 21 m | £276.51 | £13.17 | 1.05 kg |
| 22 m | £289.68 | £13.17 | 1.10 kg |
| 23 m | £302.85 | £13.17 | 1.15 kg |
| 24 m | £316.02 | £13.17 | 1.20 kg |
| 25 m | £329.19 | £13.17 | 1.25 kg |
| 26 m | £342.33 | £13.17 | 1.30 kg |
| 27 m | £355.50 | £13.17 | 1.35 kg |
| 28 m | £368.67 | £13.17 | 1.40 kg |
| 29 m | £381.84 | £13.17 | 1.45 kg |
| 30 m full coil | £338.40 | £11.28 | 1.50 kg |
Materials and compliance
This profile is made from solid neoprene (polychloroprene, CR), a general-purpose synthetic rubber. The manufacturer states that it is 100 % recyclable. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required. Ask us for a certified alternative.
How it fits

- Check the edge. Deburr, clean and dry it, and check the sheet is about 1.5 mm thick.
- Push on. Start at one end and press the channel down along the edge by hand. You need no tools.
- Cut and join. Cut slightly over-length with a sharp knife or shears, then push the ends together into a tight butt joint.
- Bond if needed. Where there is vibration, or where you need a sealed fit (for example round an aluminium window channel), run a bead of polyurethane or silicone sealant into the slot before fitting.
Typical uses
- Edge protection on 1.5 mm sheet metal, machine guards and enclosure panels
- Finishing the cut edges of doors, hatches and plastic or wooden panels
- Knock protection on vending machines, cabinets, furniture and running boards
- Edging glass or polycarbonate of the right thickness
- Safety edging on stair nosings and step plates where a 1.5 mm edge is exposed
FAQ
What thickness of panel does it fit?
It is made for 1.5 mm material. The 1.5 mm slot grips at the mouth and widens slightly towards the base, so it pushes on firmly. For thinner sheet you can bond a thin rubber strip inside the slot to pack it out. For thicker material choose a channel with a wider slot.
How do I measure what I need?
Measure the sheet thickness with a caliper, and the total run of edge in metres. Add about 5 % for cutting. Choose the next length up, or a full 30 m coil if you need more than 25 m, because the full coil is cheaper than 26 to 29 m.
Will it stay on without glue?
On a clean 1.5 mm edge it holds by grip alone for most static uses. On moving doors, vibrating machinery or outdoor parts, bond it with polyurethane or silicone sealant.
Can it be used outdoors?
Yes. Neoprene is a weather-resistant rubber. Note that the manufacturer's ozone test (72 h at 40 °C, 25 pphm) records "some cracks", so for long-term exposure in high-ozone areas, such as near electric motors or in strong sunlight, check it regularly or ask us about an EPDM channel.
What temperatures can it take?
The manufacturer rates it from −20 °C to +90 °C. For hotter or colder duty, ask us about a silicone U channel.
How do I cut and join it?
Cut it with a sharp knife, shears or a fine-tooth saw for a square end. Butt the ends tightly together. For a sealed joint, bond the ends with a flexible adhesive or sealant. To go round a corner, notch the base slightly so the channel bends without lifting.
Is it food safe or WRAS approved?
No approvals are stated for this profile, so it should not be used where food-contact or drinking-water certification is needed.
Is it in stock?
Yes. We hold it in stock and it is supplied as one continuous length cut to the size you choose.
Complete your project
- EPDM U Channel – 5.4mm x 9.7mm – Black Rubber Edge Trim
- EPDM U Channel – 4.8mm x 9.6mm – Black Rubber Edge Trim
- EPDM Rubber U Channel – 5.5mm x 8.5mm to Fit 3mm Panel
Need help choosing or fitting? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-NUC-4.5X8.5-15 |
|---|---|
| Weight | 1.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Neoprene Square U Channel – 4.5mm x 8.5mm – Black Rubber Edge Trim