
Rubber & FoamSKU IP-SGDS-24X15-L08
Self-Grip Door Seal 24mm x 15mm with 16mm Sponge Bulb – EPDM, Fits 1.6-3mm Panels – 8m to 50m
Price shown updates with the option you pick.
A push-on door seal for 1.6 mm to 3 mm edges: a solid EPDM U-clip with a steel wire insert and gripping fins inside, plus a large round EPDM sponge bulb (16 mm across) on its side. The clip holds the bare panel edge with no glue or screws. When the door, hatch or lid closes against the side bulb, the bulb squashes and seals out rain, draughts and dust. The profile is 24 mm wide overall and about 15 mm high; the clip is 10 mm wide with a 12.5 mm deep grip and a 5 mm mouth. Choose one continuous length from 8 m to 24 m, a full 25 m coil, or two full coils (50 m). It is held in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet, panel and flange edges 1.6 mm to 3 mm thick
- Size: 24 mm overall width × 15 mm nominal height; U-clip 10 mm wide, 12.5 mm grip depth, 5 mm slot mouth; sponge bulb Ø16 mm outside with an Ø11 mm bore
- Construction: solid EPDM U-clip (80° Shore A) over a full-length steel wire carrier, with angled fins on both inner walls; hollow closed-cell EPDM sponge bulb
- Seals best when the closed door squeezes the bulb by 30–40 % (about 5–6 mm). Do not go past 50 % (8 mm).
- Working temperature: −40 °C to +80 °C
- Price: £18.63 per metre inc VAT for 8 m to 24 m. The full 25 m coil is £13.98 per metre (£349.50), so it costs less than any cut length from 19 m up.
Technical drawing

How it fits

- Clean the edge and file off any burrs, rust or weld spatter.
- Start at the bottom or the middle of a straight run, never on a corner.
- Push the seal onto the edge by hand, a short section at a time, with the bulb on the side the door closes against.
- Tap it fully home with a rubber or plastic mallet. The edge should reach the top of the 12.5 mm grip.
- Ease it round corners with a radius of about 30 mm or more. Do not stretch it, or it will shrink back and leave a gap.
- Cut the end square, butt it tight to the start, and close the door to check that the bulb is squeezed evenly all round.

With the door shut, the gap from the flange face to the door is about 12 mm (11.5–13 mm), which squeezes the bulb by the ideal 30–40 %.
Typical uses
- Restoration and replacement door, boot and bonnet seals on older vehicles with 1.6–3 mm flanges
- Van, trailer, horsebox and catering-trailer doors and lockers
- Electrical cabinets, control panels and outdoor enclosures with wide door gaps
- Machine guards, access panels and inspection hatches
- Marine hatches, deck lockers and workshop doors
Specifications
Values are from the manufacturer's product page and data sheet for this profile (RCDS24X12.5L). The manufacturer quotes the size both as 24 × 12.5 mm (the clip's grip depth) and 24 × 15 mm (overall height); both are shown below.
| Property | Value | Test method / note |
|---|---|---|
| Dimensions | ||
| Overall width (clip + bulb) | 24 mm | Nominal |
| Overall height | 15 mm | Nominal, as quoted by the manufacturer |
| U-clip width | 10 mm | Nominal |
| Grip depth (inside the U-clip) | 12.5 mm | Nominal |
| Slot mouth | 5 mm | Nominal, between the leg tips |
| Sponge bulb outside diameter | 16 mm | Nominal |
| Sponge bulb bore | 11 mm | Nominal |
| Panel / edge thickness it fits | 1.6 mm to 3 mm | Manufacturer's fitting range |
| Dimensional tolerance | Not published | Ask us if your application is critical |
| Supplied length | 8 m to 24 m (1 m steps), 25 m full coil, or 2 × 25 m coils | Cut lengths are one continuous piece |
| Colour | Black | |
| Solid U-clip | ||
| Polymer | EPDM, solid | |
| Hardness | 80° Shore A | Shore A |
| Tensile strength | 80 kg/cm² min (about 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm min (about 29 N/mm) | ASTM D624 |
| Compression set | 40 % max | ASTM D395 Type B |
| Change in tensile strength | +15 % | As listed on the data sheet (conditions not stated) |
| Ozone resistance | No cracks at 20 % elongation | ASTM D1149 |
| Sponge bulb | ||
| Polymer | EPDM, closed-cell sponge | |
| Density (indicative) | 550–600 kg/m³ | Data sheet prints the unit as g/cm³ |
| Water absorption | 1.2 % max | ASTM D1056 |
| Tensile strength | 7–10 kg/cm² (about 0.7–1.0 MPa) | ASTM D412 |
| Tear resistance | 0.6–0.8 kg/mm (about 5.9–7.8 N/mm) | ASTM D624 |
| Steel wire carrier | ||
| Grade | Fe 50 (UNI 5961-67) | |
| Hardness | 80–90 HRB | Rockwell B |
| Tensile strength | 50 kg/mm² min (about 490 MPa) | |
| Complete profile | ||
| Staining (migration and contact) | Satisfactory | ASTM D925 |
| Colour fastness | Satisfactory | ASTM D750 |
| Operating temperature | −40 °C to +80 °C | Manufacturer's rating |
| Bulb compression | 30–40 % ideal, 50 % max | Manufacturer's guidance |
| Elongation at break | Not published | |
Materials and compliance
The clip is solid EPDM rubber with a steel wire carrier moulded inside it. The bulb is closed-cell EPDM sponge. EPDM resists UV, ozone, rain and many everyday detergents and chemicals well, which is why it is the usual choice for outdoor door seals. The manufacturer does not publish any food-contact, WRAS, REACH or RoHS statement for this profile, so we do not claim one. If you need a declaration for your project, ask us before you order.
How much do I need?
Measure all the way round the opening or edge you want to seal and add about 2 % for trimming and the butt joint. For example, a car door aperture of about 1.0 × 1.1 m needs roughly 2 × (1.0 + 1.1) = 4.2 m, so two doors need about 8.6 m: order 9 m. Each cut length is sent as one continuous piece. From 19 m up, the 25 m coil is the cheaper choice.
Frequently asked questions
What thickness of edge will it grip?
Edges from 1.6 mm to 3 mm, which covers most sheet-steel and aluminium door flanges. Thinner than 1.6 mm and it may slide; thicker than 3 mm and it will not seat fully. Ask us for a profile to suit other thicknesses.
Do I need glue or screws?
No. The steel wire insert and the angled fins grip the edge on their own. At the start and end of a run, or on an edge that gets knocked a lot, a dab of contact adhesive in the slot can help.
Which side should the bulb go?
Fit it so that the bulb faces the part that closes against it, such as the door skin or the hatch lid. Aim for the closed door to squash the 16 mm bulb by about 5–6 mm.
Will it fit my classic car?
It is a common profile for doors and boot lids on many older British vehicles with a 1.6–3 mm pinch-weld flange and a wide door gap. Check your flange thickness and the gap between the flange face and the closed door (about 11.5–13 mm suits this seal) before you order, or send us a photo and we will check it for you.
Can it go round corners?
Yes, it bends round corners with a radius of about 30 mm or more. On a sharp 90° corner, cut a small V-notch in the back of the clip, or mitre and butt two pieces.
How do I cut and join it?
Use heavy-duty side cutters or a fine-tooth hacksaw to go through the steel wire, then tidy the sponge with a sharp knife. Butt the two ends tightly together. You can bond the sponge faces with cyanoacrylate (superglue) for a fully closed ring.
Is it suitable outdoors and at what temperatures?
Yes. Both the clip and the bulb are EPDM, ozone-tested and rated from −40 °C to +80 °C. Keep it away from exhausts and other hot surfaces.
Will it mark paintwork?
The manufacturer rates it satisfactory for migration and contact staining (ASTM D925). As with any rubber product, try it on a hidden area first if the finish is pale or freshly painted.
Is it in stock?
Yes. Orders placed before the cut-off time on working days are dispatched the same day from our UK stock.
Need help choosing the right profile? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SGDS-24X15-L08 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip Door Seal 24mm x 15mm with 16mm Sponge Bulb – EPDM, Fits 1.6-3mm Panels – 8m to 50m