Rubber & FoamSKU IP-SLP-20X15X1.3-BLACK-10
Silicone L Profile – 20mm x 15mm, 1.3mm Thin Wall, Tapered Flange – 10m or 25m Coil
Price shown updates with the option you pick.
A slim, unequal-leg silicone L profile, 20mm x 15mm, with a 1.3mm wall and a tapered 20mm flange that thins to a 0.2mm feather edge. The thin wall keeps the trim discreet and flexible, and the feathered flange blends into the surface it sits on instead of leaving a hard step. Use it as an angle trim, corner protector or light angle seal on cabinets, enclosures, glazing and food equipment. Made in 60 Shore A silicone that works from -50°C to +180°C, in seven colours, on 10m or 25m coils held in UK stock.
At a glance
- Size: 20mm wide x 15mm high, unequal-leg L (angle) section
- Wall: 1.3mm upright; flange 1.3mm at the root, tapering over 16.3mm to a 0.2mm feather edge; R1 inside corner
- Material: 60 Shore A silicone rubber, 1.15 g/cm³
- Temperature: -50°C to +180°C working range
- Compliance stated by the manufacturer: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved, free from TSE/BSE-derived products and phthalates
- Colours: black, blue, green, red, translucent, white and yellow, all at the same price
- Supplied as: 10m coil (£75.00/m) or 25m coil (£39.60/m), cut to length yourself
Which 20 x 15mm L profile do I need?
| Version | Section | Hardness | Best for |
|---|---|---|---|
| Thin wall (this product) | 1.3mm upright, flange tapering 1.3 to 0.2mm | 60 Shore A | Discreet angle trim and light sealing where low bulk and a flush, feathered edge matter |
| Heavy section | Solid 10mm upright and 7mm base | 50 Shore A | Thick, cushioned bumpers and corner guards that take knocks |
Technical drawing
![]()
All dimensions are the manufacturer's nominal values in mm. Tolerances to ISO 3302-1:2014 class E2.
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile | L (angle) section, unequal legs, tapered flange | Manufacturer's drawing |
| Overall width (flange leg) | 20 mm | Nominal |
| Overall height (upright leg) | 15 mm | Nominal |
| Upright wall thickness | 1.3 mm | Nominal |
| Flange thickness at root | 1.3 mm | Nominal |
| Flange thickness at tip | 0.2 mm (feather edge) | Nominal |
| Length of tapered section | 16.3 mm | Nominal |
| Inside corner radius | R1 mm | Nominal |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 10 m or 25 m continuous | One coil per unit |
| Material | Silicone rubber | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175°C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | Manufacturer's data |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | Manufacturer's data |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
The manufacturer's datasheet for this exact profile states that the compound meets:
- FDA 21 CFR 177.2600 (rubber articles for repeated food contact)
- EC 1935/2004 (EU food-contact materials framework)
- WRAS approved material (for use with drinking water)
- Free from TSE/BSE-derived products
- Free from phthalates
We list only the approvals the manufacturer states in writing for this product. If you need a declaration of conformity or a certificate for an audit, ask us before ordering.
How it fits
![]()
The inside of the L sits over an external 90° corner: the 15mm upright covers the side face and the 20mm flange runs along the top. Because the flange thins to 0.2mm, its tip flexes down onto the surface and finishes almost flush, so there is no ledge to catch dirt or snag cloths. The R1 inside radius suits sheet and panel corners with a small edge radius.
Typical uses
- Corner trim and edge protection on sheet-metal cabinets, enclosures and machine guards
- Light angle seal along doors, hatches, inspection panels and HVAC housings
- Hygienic edge finish on food and beverage processing equipment
- Clean, wipe-down edging in laboratories and cleanrooms
- Edge finish on glass, acrylic and composite panels
- Colour-coded edges for zoning or hazard marking
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and mitres. Example: the four top edges of a 1200mm x 600mm enclosure lid total 3.6m, plus 5% is about 3.8m. Two lids fit on one 10m coil; for six or more lids the 25m coil works out at £39.60 a metre against £75.00 on the 10m coil.
Fitting tips
- Clean and degrease the corner first; silicone bonds and grips best on a dry surface.
- Cut with a sharp knife or shears against a straight edge. Mitre the corners at 45° for a neat return.
- Lay the profile on without stretching it, or it may pull back and open the joints later.
- For a permanent or watertight fit, bond it with a silicone or compatible polyurethane adhesive sealant run into the inside of the angle.
Questions
What size corner does it fit?
Any external 90° corner. The upright covers 15mm down the side face and the flange covers 20mm across the top. The edges of the object can be any thickness, because the L sits on the outside of the corner rather than gripping it.
How is it different from the heavy 20 x 15mm L profile?
The outside size is the same, but this one has a 1.3mm wall and a tapered flange, so it is light, flexible and low profile. The heavy-section version has solid 10mm and 7mm legs in softer 50 Shore A silicone for impact protection.
Will it stay on without glue?
On its own it rests on the corner rather than clipping on, so for anything other than temporary protection bond it with a silicone or compatible polyurethane sealant.
Is it safe for food areas and drinking water?
The manufacturer states the compound complies with FDA 21 CFR 177.2600 and EC 1935/2004 for food contact and is a WRAS approved material.
What temperatures can it take?
-50°C to +180°C continuous working range. It stays flexible in freezers and next to ovens, and resists UV, ozone and weathering outdoors.
Can I cut and join it?
Yes. Cut it with a sharp blade, mitre corners at 45°, and join ends with a silicone adhesive or a dab of silicone sealant. It will not fray or delaminate.
Can it go round curves?
It bends easily along gentle curves. For tight radii, notch the flange so it does not ripple.
When will it arrive?
All colours and both coil lengths are held in UK stock and dispatched as shown at checkout.
Need help choosing? Contact our team or call +44 1282 277786.
Product details
| SKU | IP-SLP-20X15X1.3-BLACK-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 20mm x 15mm, 1.3mm Thin Wall, Tapered Flange – 10m or 25m Coil