Rubber & FoamSKU IP-SILP-51X26X6.3-BLACK-10
Silicone L Profile – 51mm x 26mm, 6.3mm Wall – 10m or 25m Coil
Price shown updates with the option you pick.
This silicone L profile 51mm x 26mm is a wide, unequal-leg angle extrusion with a sturdy 6.3mm wall, made for capping and protecting broad panel edges, sealing enclosure doors and finishing food and water equipment. It is sold per 10m or 25m coil in seven colours.
At a glance
- Unequal angle: 51mm long leg, 26mm short leg, 6.3mm wall on both legs
- 60 Shore A silicone rubber, flexible but holds a crisp right angle
- Works from -50°C to +180°C, from chillers to oven housings
- Resists UV, ozone and weathering for outdoor edge trim
- Material meets FDA 21 CFR 177.2600 and is WRAS approved
- Black, blue, green, red, translucent, white or yellow for colour coding
Typical uses
- Wide rubber angle trim on sheet-metal and glass panel edges
- Corner seal on machine guards, hatches and enclosure doors
- Edge protector on food and drink processing equipment
- Gasket strip in potable water tanks and HVAC housings
- Colour-coded edge finishing in cleanrooms and laboratories
Which one do I need?
| Profile | Best for |
|---|---|
| Silicone L profile 40mm x 25mm | Narrower long leg for medium panels |
| Silicone L profile 51mm x 26mm (this profile) | Wide 51mm face with a 26mm return and 6.3mm wall |
| Silicone L profile 58mm x 32mm | Deeper return for thicker edges |
| Silicone L profile 65mm x 20mm | Extra-wide face with a shallow return |
Technical drawing
Specification
| Profile | Unequal L (angle) section |
| Long leg | 51mm |
| Short leg | 26mm |
| Wall thickness | 6.3mm |
| Material | Silicone rubber |
| Hardness | 60 Shore A |
| Density | 1.15 g/cm³ |
| Tensile strength | 11 N/mm² |
| Elongation at break | 550% |
| Tear strength | 26 N/mm |
| Compression set | 31% (22 hours at 175°C) |
| Temperature range | -50°C to +180°C |
| Food and water | FDA 21 CFR 177.2600; WRAS approved |
| Colours | Black, blue, green, red, translucent, white, yellow |
| Unit of sale | 10m or 25m coil |
How much do I need?
Measure every edge to be trimmed and add 5% for mitres and trimming. Example: four enclosure doors at 4.5m of edge each need 18m, plus 5% is about 19m, so one 25m coil is the better buy than two 10m coils and leaves spare for repairs.
Fitting tips
- Clean and degrease the edge first; silicone grips best on a dry surface.
- Cut with a sharp knife against a straight edge for a square end.
- Push-fit for light protection; bond with a silicone sealant for a permanent or watertight joint.
- Mitre corners at 45° so the 51mm leg lies flat instead of buckling.
Complete your project
- Silicone L Profile – 40mm x 25mm – 10m or 25m Coil
- Silicone L Profile – 58mm x 32mm – 10m or 25m Coil
- Silicone L Profile – 65mm x 20mm – 10m or 25m Coil
Questions
Is this edge protector suitable for food contact?
Yes. The silicone meets FDA 21 CFR 177.2600, so it can be used on food and drink processing equipment.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering, so the corner seal will not crack or harden in sunlight.
Which leg goes where?
Fit the 51mm leg on the wider face and the 26mm leg over the return edge; it can be turned either way to suit the panel.
Do I need adhesive?
Not for light edge protection. For a sealed or permanent fit, bond it with a compatible silicone sealant.
Need help choosing? Contact our team with your application and edge size and we will point you to the right profile.
Product details
| SKU | IP-SILP-51X26X6.3-BLACK-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 51mm x 26mm, 6.3mm Wall – 10m or 25m Coil