Rubber & FoamSKU IP-SIRU-3X5-25-BLACK
Silicone Round U Channel – 3mm x 5mm for 1mm Edges – 25m Coil
A miniature silicone U channel, just 3mm across and 5mm tall, made to grip the thinnest edges: 1mm sheet metal, glass slips, film, mesh and fine panels. The rounded base gives a smooth, soft finish, and the 1mm slot holds firmly without adhesive on most 1mm edges. The compound is food-contact and drinking-water approved (see Material compliance). Supplied as one continuous 25m coil in a choice of seven colours.
At a glance
- Fits edges about 1mm thick
- 3mm wide x 5mm high, 1mm slot, 4mm slot depth, rounded 1.5mm radius base
- Silicone rubber, 60 Shore A: soft, flexible and follows tight curves
- Works continuously from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Resists UV, ozone and weathering, so it will not crack or go brittle outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, about £27.00 per metre
Typical uses
- Finishing the edges of thin stainless guards and covers on food and packaging machinery
- Protecting wiring from raw 1mm sheet-steel edges in control panels and enclosures
- Cushioning thin glass or acrylic in instrument cabinets, displays and lab equipment
- Edge trim on equipment in contact with drinking water, such as tank lids and access panels
- Edge trim on heater, oven and lighting panels where rubber or PVC would soften or harden
- Colour-coding panels, trays and fixtures by line, zone or product
Which size do I need?
Measure the thickness of the edge you are covering and pick the slot that matches.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 3mm x 5mm (this one) | 1mm |
| Silicone U Channel 7.1mm x 13mm | 4mm |
| Silicone U Channel 15mm x 20mm | 10mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel (push-on edge trim) | – |
| Overall width | 3 mm | – |
| Overall height | 5 mm | – |
| Slot (grip) width | 1 mm | – |
| Slot depth | 4 mm | – |
| Wall thickness | 1 mm each side | – |
| Base thickness | 1 mm, outer radius 1.5 mm | – |
| Fits panel / edge | 1 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 12 g per metre, approx. 0.3 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states the silicone compound meets the following:
- FDA 21 CFR 177.2600: the US rule for rubber articles intended for repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for materials in contact with food
- WRAS approved: approved for use in contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: no phthalate plasticisers
These approvals cover the material. Whether a finished assembly complies depends on how and where it is used. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow around 5% for trimming and joints. Example: twenty 1mm steel guard covers, each with a 1.1m exposed edge, need 22m, or about 23.1m with allowance, so one 25m coil does the job.
Fitting tips
- Deburr and wipe the edge clean before fitting
- Start at one end and press the channel on with your thumb as you go
- Cut with a sharp knife or scissors, slightly over length, and push the ends together for a neat butt joint
- For thinner edges, or a sealed or permanent fit, run a bead of silicone sealant into the slot first
Questions
Is it safe for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Will it fit a 0.7mm or 1.2mm edge?
The slot is 1mm and silicone stretches a little, so around 1.2mm is usually fine. On thinner edges add a silicone sealant so it cannot slide off.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Can it go round corners?
Yes. At 60 Shore A and only 3mm wide it bends easily round curves. On a sharp 90° corner, cut a small V notch in the base or butt two lengths together.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
Can I order a shorter length?
This listing is a full 25m coil. For cut lengths or larger quantities, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or a seal? Contact our team.
Product details
| SKU | IP-SIRU-3X5-25-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 3mm x 5mm for 1mm Edges – 25m Coil