Rubber & FoamSKU IP-SILT-12X10.5-BLACK
Silicone T Seal Profile – 12mm x 10.5mm, 12mm Flat Head, 5mm Leg – 80 Shore A – 25m Coil
A firm, solid silicone T seal with a wide, low head: 12mm across and 4.5mm deep, on a 5mm push-in leg, 10.5mm tall overall. Press the leg into a slot about 4.8–5.0mm wide and the flat head sits 4.5mm proud of the frame, with a 3.5mm shoulder covering the slot edge on each side. At 80 Shore A it is one of the hardest T seals we sell, so it holds a crisp, straight line in a slot and stands up to knocks, cleaning and foot or trolley traffic better than a soft seal. It works from -50°C to +180°C, comes in seven colours at the same price, and is supplied as one unbroken 25m coil.
At a glance
- Head 12.0mm wide × 4.5mm deep; leg 5.0mm wide; 10.5mm overall (6.0mm of leg below the head)
- 3.5mm shoulder each side of the leg, so the head hides both edges of the slot
- 80 Shore A solid silicone: firm, hard-wearing and dimensionally stable
- Working range -50°C to +180°C
- The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and that it is a WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all £675.00 per 25m coil (£27.00 per metre)
- Held in stock in every colour
Typical uses
- Infill and cover strips in slotted stainless worktops, counters and catering equipment
- Expansion and panel joints between cabinets, enclosures and machine guards
- Edge seals on refrigeration, hot-cupboard and warming-equipment panels where the joint is closed once and stays closed
- Duct, air handling unit and access-panel joints
- Outdoor and marine hatch frames and panel joints, where UV and ozone crack ordinary rubbers
- Colour-coded strips for hygiene zones (red, green, blue, yellow) or easy visual inspection (white, translucent)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, centred leg | – |
| Overall height | 10.5 mm | – |
| Head width | 12.0 mm | – |
| Head depth | 4.5 mm | – |
| Leg width (base thickness) | 5.0 mm | – |
| Leg length below head | 6.0 mm (reference, 10.5 − 4.5) | – |
| Shoulder each side | 3.5 mm (reference, leg centred) | – |
| Suits slot (our guidance) | Approx. 4.8–5.0 mm wide, at least 6 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 54 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 101 g per metre, 2.5 kg per coil (calculated from the 84 mm² section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part number | IP-SILT-12X10.5-<colour> | – |
All property values are the manufacturer's data for this profile. Slot size and closed-gap figures are our own fitting guidance.
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Is this the right T seal for the job?
Choose this profile when you want a hard-wearing, low, wide head that fills and covers a 5mm slot neatly: worktop and panel joints, cover strips, and seals that are squeezed once and then left. Its compression set is 78% after 22 hours at 175°C, which means that when it is held squeezed at high heat it takes on that squeezed shape. For an oven or hot-cupboard door that opens and closes all day at high temperature, a softer 60 Shore A T seal with a deeper head will recover better. Ask us and we will suggest one.
Will it fit my slot?
Measure the slot's width and depth. The leg is 5mm wide, so it grips best in a slot of about 4.8–5.0mm. The slot should be at least 6mm deep so the head can sit right down on the frame; deeper is fine. You need about 3.5mm of flat land either side of the slot for the shoulders. If something closes onto the head, it stands 4.5mm proud: as a guide (our advice, not a supplier figure), a closed gap of about 3.5–4.0mm gives a firm seal on this hard compound without crushing it.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 1.8m × 0.6m worktop with one slot down each long side needs 3.6m, or about 3.8m with the allowance, so one 25m coil does six worktops of that size.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. At 80 Shore A it is firm, so a drop of soapy water helps it slide into a tight slot.
- If the slot is loose or the seal must not move, run a bead of silicone adhesive into the slot first
- The wide, hard head will not bend round a tight corner: mitre the head at 45° and butt the ends, or notch the head and keep the leg continuous. Don't stretch it round: stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 4.8–5.0mm wide and at least 6mm deep. The head is 12mm wide, so it overlaps the slot by 3.5mm each side.
Which way up does it go?
The 5mm leg goes into the slot. The flat 12mm head sits on the frame face, with its top facing outwards or towards the part that closes onto it.
How hard is it?
80 Shore A, a firm silicone, close to the feel of a hard shoe heel. It keeps a sharp, straight edge and resists wear, but it is much stiffer to squeeze than our 60 Shore A T seals.
Is it food safe?
The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is also listed as a WRAS approved material for drinking water.
What temperatures can it take?
The working range is -50°C to +180°C. Because the compression set is 78% after 22 hours at 175°C, it is best at high heat as a fixed joint or trim rather than on a door that is opened and closed all day.
How do I cut and join it?
Cut it with a sharp utility knife or heavy shears on a cutting board, using a square to keep the cut straight. Butt the ends together, with a little silicone adhesive or RTV if the joint must stay sealed.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering, which crack ordinary rubbers in outdoor and marine use.
Do you stock every colour?
Yes. All seven colours are held in stock at the same price and dispatch with our standard delivery.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk with your slot and gap sizes.
Product details
| SKU | IP-SILT-12X10.5-BLACK |
|---|---|
| Weight | 5.95 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 12mm x 10.5mm, 12mm Flat Head, 5mm Leg – 80 Shore A – 25m Coil