Rubber & FoamSKU IP-SILT-12X8-BLACK
Silicone T Seal Profile – 12mm x 8mm, 12mm Flat Head, 4mm Leg – 60 Shore A – 25m Coil
A wide, low silicone T seal: a 12mm flat head only 3.5mm deep, on a 4mm push-in leg, 8mm tall overall. Press the leg into a slot about 3.8–4.0mm wide and the head sits 3.5mm proud of the frame, with a generous 4mm shoulder lying flat on the face either side. That broad, thin head covers a wide joint or a slightly ragged slot edge neatly, and gives a closing door, lid or panel a 12mm band of soft silicone to seal against. Made from 60 Shore A silicone for -50°C to +180°C, it comes in seven colours at the same price, in one unbroken 25m coil.
At a glance
- Head 12.0mm wide × 3.5mm deep; leg 4.0mm wide; 8.0mm overall (4.5mm of leg below the head)
- 4.0mm shoulder each side of the leg, so the head covers both edges of the slot with room to spare
- 60 Shore A solid silicone, working range -50°C to +180°C
- The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and that it is a WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all £675.00 per 25m coil (£27.00 per metre)
- Held in stock in every colour
Typical uses
- Oven, prover, hot-cupboard and drying-cabinet doors, up to +180°C
- Expansion and panel joints between stainless cabinets, worktops and enclosures, where the wide head hides the joint
- Access hatches and guards on food, bakery and packaging machinery
- Heater housings, air handling units and duct access panels
- Outdoor and marine hatches and enclosures, where UV and ozone crack ordinary rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow) or easy visual inspection (white, translucent)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, centred leg | – |
| Overall height | 8.0 mm | – |
| Head width | 12.0 mm | – |
| Head depth | 3.5 mm | – |
| Leg width (base thickness) | 4.0 mm | – |
| Leg length below head | 4.5 mm (reference, 8.0 − 3.5) | – |
| Shoulder each side | 4.0 mm (reference, leg centred) | – |
| Suits slot (our guidance) | Approx. 3.8–4.0 mm wide, at least 4.5 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 69 g per metre, 1.7 kg per coil (calculated from the 60 mm² section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part number | IP-SILT-12X8-<colour> | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 4mm wide, so it grips best in a slot of about 3.8–4.0mm. The slot should be at least 4.5mm deep so the head can sit down on the frame; deeper is fine, and the head simply rests on the face. You need about 4mm of flat land either side of the slot for the shoulders. Then check the closed gap: the head stands 3.5mm proud, so the door or lid should close to roughly 2.5–3.2mm from the frame face to squeeze the head without crushing it.
See the fitting guide in the gallery for a true-proportion section through a fitted seal.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm oven or guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. A drop of soapy water helps it slide into a tight slot.
- If the slot is loose or the seal must not move, run a bead of silicone adhesive into the slot first
- At a tight corner, notch the wide head with a 90° V-cut so it folds flat and keep the leg continuous, or cut and butt-join it. Don't stretch it round: stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 3.8–4.0mm wide and at least 4.5mm deep. The head is 12mm wide, so it overlaps the slot by 4mm each side.
Which way up does it go?
The 4mm leg goes into the slot. The flat 12mm head lies on the frame and its top faces the door, lid or panel it seals against.
How big a gap will it seal?
The head stands 3.5mm proud of the frame. It seals best when the closed door or lid squeezes it by about 10–30%, so it suits a closed gap of roughly 2.5–3.2mm. For a bigger gap, choose one of our T seals with a deeper head.
Is it food safe?
The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is also listed as a WRAS approved material for drinking water.
What temperatures can it take?
The working range is -50°C to +180°C. Compression set is 31% after 22 hours at 175°C, so it keeps sealing on hot doors.
How do I cut and join it?
Cut it with a sharp utility knife or heavy shears on a cutting board, using a square to keep the cut straight. Butt the ends together, with a little silicone adhesive or RTV if the joint must stay sealed.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering, which crack ordinary rubbers in outdoor and marine use.
How hard is it?
60 Shore A, a firm silicone, about the feel of a car tyre tread. It holds its shape in the slot but still compresses under a closing door.
Do you stock every colour?
Yes. All seven colours are held in stock at the same price and dispatch with our standard delivery.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk with your slot and gap sizes.
Product details
| SKU | IP-SILT-12X8-BLACK |
|---|---|
| Weight | 3.97 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 12mm x 8mm, 12mm Flat Head, 4mm Leg – 60 Shore A – 25m Coil