Rubber & FoamSKU IP-SILT-15X10-L5-BLACK
Silicone T Seal Profile – 15mm x 10mm, 5mm Leg – 80 Shore A, Food Grade – 25m Coil
A firm silicone T seal with a wide, flat head: 15mm × 5mm on a 5mm wide × 5mm push-in leg, 10mm tall overall. Press the leg into a slot of about 4.5–5mm and the head covers 5mm of face either side, bridging wide joints and uneven edges. The 5mm deep head stands proud of the frame for the door, lid or panel to close onto. Made from 80 Shore A silicone for -50°C to +180°C, it comes in seven colours at the same price, in one unbroken 25m coil. Looking for a different slot width? We also list the 10mm leg version of this 15 × 10mm profile.
At a glance
- Head 15.0mm wide × 5.0mm deep; leg 5.0mm wide × 5.0mm long; 10.0mm overall
- 5mm shoulder each side of the centred leg, so the head covers both edges of the slot
- Firm 80 Shore A solid silicone, working range -50°C to +180°C
- The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and that it is a WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all £675.00 per 25m coil (£27.00 per metre)
- Held in stock in every colour
Typical uses
- Oven, prover, hot-cupboard and drying-cabinet doors, up to +180°C
- Access hatches and guards on food, bakery, brewery and packaging machinery
- Expansion and panel joints between stainless cabinets, worktops and enclosures
- Heater housings, air handling units and duct access panels
- Outdoor and marine hatches and enclosures, where UV and ozone crack ordinary rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow) or easy visual inspection (white, translucent)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, centred leg | – |
| Overall height | 10.0 mm | – |
| Head width | 15.0 mm | – |
| Head depth | 5.0 mm | – |
| Leg width (supplier's "base thickness") | 5.0 mm | – |
| Leg length below head | 5.0 mm (reference, 10.0 − 5.0) | – |
| Shoulder each side | 5 mm (reference, leg centred) | – |
| Cross-section area | 100 mm² (calculated) | – |
| Suits slot (our guidance) | Approx. 4.5–5 mm wide, at least 5.5 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 54 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 120 g per metre, 3.0 kg per coil (calculated from the 100 mm² section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part number | IP-SILT-15X10-L5-<colour> | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
![]()
Measure the slot's width and depth. The leg is 5mm wide, so it grips best in a slot of about 4.5–5 mm. The slot should be at least 5.5mm deep so the head can sit down on the frame; deeper is fine. You need about 5mm of flat land either side of the slot for the shoulders. Then check the closed gap: the head stands 5mm proud, so the door or lid should close to roughly 3.5–4.5mm from the frame face to squeeze the head without crushing it.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm oven or guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. A drop of soapy water helps it slide into a tight slot.
- If the slot is loose or the seal must not move, run a bead of silicone adhesive into the slot first
- 80 Shore A is firm and the 15mm head is wide, so mitre the head at tight corners, or cut and butt-join it. Don't stretch it round: stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 4.5–5 mm wide and at least 5.5mm deep. The head is 15mm wide, so it overlaps the slot by 5mm each side.
What is the difference between the 5mm and 10mm leg versions?
Only the leg. Both have the same 15 × 5mm head, 10mm overall height, 80 Shore A silicone and price. Choose the leg that matches your slot width: 5mm leg for a 4.5–5mm slot, 10mm leg for a 9.5–10mm slot.
Which way up does it go?
The 5mm leg goes into the slot. The flat head sits on the frame and faces the door, lid or panel it seals against.
How big a gap will it seal?
The head stands 5mm proud of the frame. As a guide (our advice, not a supplier figure), it seals best when the closed door or lid squeezes it by about 10–30%, so it suits a closed gap of roughly 3.5–4.5mm.
Is it food safe?
The manufacturer states in writing that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is also listed as a WRAS approved material for drinking water.
What temperatures can it take?
The working range is -50°C to +180°C. Compression set is 78% after 22 hours at 175°C, which is high: on doors held shut at high heat for long periods the head will take a set, so plan to inspect and replace it as part of routine maintenance.
How do I cut and join it?
Cut it with a sharp utility knife or heavy shears on a cutting board, using a square to keep the cut straight. Butt the ends together, with a little silicone adhesive or RTV if the joint must stay sealed.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering, which crack ordinary rubbers in outdoor and marine use.
How hard is it?
80 Shore A, a firm silicone. It holds its shape well in the slot and resists being pulled out, but needs a firm close to compress.
Do you stock every colour?
Yes. All seven colours are held in stock at the same price and dispatch with our standard delivery.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk with your slot and gap sizes.
Product details
| SKU | IP-SILT-15X10-L5-BLACK |
|---|---|
| Weight | 6.94 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 15mm x 10mm, 5mm Leg – 80 Shore A, Food Grade – 25m Coil