Rubber & FoamSKU IP-SITS-4X4.3-25M-BLK
Silicone T Seal Profile – 4mm x 4.3mm – 25m Coil
A small but very secure groove seal. This silicone T seal profile is a solid 4mm x 4.3mm extrusion with a serrated sealing face on its head and a dovetail leg that gets wider towards its base. Push the leg into an undercut (dovetail) slot and it locks under the slot lips, so it stays in place when a door, lid or panel is opened and closed many times. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- 4.0mm wide head, 1.8mm thick, with eight fine V-grooves across the top for a positive compression seal
- Dovetail leg 2.4mm at the neck widening to 3.4mm at the base, 2.5mm long: suits undercut slots
- Overall height 4.3mm; the head stands 1.8mm proud of the frame before compression
- Solid silicone rubber, 60 Shore A
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids and access hatches on food processing, packaging and bakery machinery
- Door seals on catering warming cabinets, proving cabinets and dryers
- Panel and window infill seals in aluminium or stainless frames with a dovetail groove
- Instrument and control enclosure lids where a low, neat seal line is needed
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, serrated head, dovetail leg | – |
| Head width (overall width) | 4.0 mm | – |
| Overall height | 4.3 mm | – |
| Head thickness | 1.8 mm | – |
| Head top face | 8 V-grooves across the 4.0 mm width | – |
| Leg width at neck | 2.4 mm | – |
| Leg width at base | 3.4 mm | – |
| Leg length below head | 2.5 mm (reference) | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for an undercut (dovetail) slot: about 2.4mm wide at the mouth, opening out to about 3.4mm at the bottom, and about 2.5mm deep. The leg is squeezed through the narrow mouth and then expands under the lips, which is what holds it in. In a plain straight-sided slot it will still push in, but it relies on friction alone, so add a thin bead of silicone adhesive along the bottom of the groove.
![]()
How much do I need?
Measure every groove and add about 5% for trimming and joints. Example: a machine hatch with a 500mm x 400mm groove needs 1.8m, so one 25m coil does about 13 hatches with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Feed the base of the leg into the slot mouth and roll it in with your thumb or a plastic roller; it may help to tilt the seal slightly so one edge of the leg enters first
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The wide end of the leg goes into the slot. The serrated head stays on the outside, facing the door, lid or panel that closes onto it.
What are the grooves on top for?
The eight small V-grooves give a series of fine ridges that compress first, so the seal closes on a low closing force and copes with small surface imperfections.
Do I need a dovetail slot?
That is what it is designed for, and it gives the best retention. It can be used in a straight slot about 2.4 to 3.4mm wide if you bond it with silicone adhesive.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits warming cabinets, dryers and machinery that runs hot. For hotter zones, ask us about a higher-rated profile.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber. Check your slot against the drawing before ordering.
Will it take a permanent set?
Silicone recovers well. This compound has a compression set of 31% after 22 hours at 175°C and 59% rebound resilience, so it keeps sealing through repeated heat cycles.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Is every colour the same price and size?
Yes. All seven colours are the same 4mm x 4.3mm profile and the same price, so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 4mm x 6.5mm (straight leg for plain slots)
- High-Temperature Silicone P Extrusion – 30mm x 12mm
- Silicone U Channel – 7.1mm x 13mm for 4mm Panels
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-4X4.3-25M-BLK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4mm x 4.3mm – 25m Coil