Rubber & FoamSKU IP-SITS-6X5.2-40-25M-BLK
Silicone T Seal Profile – 6mm x 5.2mm – 40 or 80 Shore A – 25m Coil
A solid silicone T seal with a broad, flat head 6mm wide and 2mm thick on a 3.2mm leg, 5.2mm tall overall. Push the leg into a slot about 3.0–3.2mm wide and the head sits flat on the surface, closing the gap against dust, splash, draughts and heat. It is a low-profile seal: the head stands only 2mm proud, so it suits doors and lids with little clearance. Choose a soft 40 Shore A or a hard 80 Shore A compound in the same profile, in seven colours, all at the same price. Each coil is one unbroken 25m length.
At a glance
- Head 6.0mm wide × 2.0mm thick; leg 3.2mm wide; 5.2mm overall height (3.2mm of leg below the head)
- 1.4mm shoulder each side of the leg, so the head covers both slot edges
- Two hardnesses in the identical profile: 40 Shore A (soft) or 80 Shore A (hard)
- Solid silicone rubber, working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour and hardness
Which hardness do I need?
| 40 Shore A (soft) | 80 Shore A (hard) | |
|---|---|---|
| Feel | Soft and rubbery, squashes easily | Firm, close to a hard plastic trim |
| Closing force | Low: seals under light, hand-closed lids | High: needs a latched or clamped door to compress |
| Copes with uneven gaps | Better: conforms to warped or uneven faces | Less: best on flat, rigid faces |
| Holds its shape / resists wear | Good | Better: resists scuffing, cutting and being pushed out of the slot |
| Compression set (22 h at 175 °C) | 36 % | 78 % |
| Best for | Sealing doors, lids and hatches against air, dust and splash | Edge trims, bumpers, glazing and wear strips where stiffness matters more than squash |
If you are sealing a closing door or lid, the 40 Shore A version is usually the right choice. It needs less force and recovers better after long periods compressed.
Typical uses
- Slot seals in machine guards, enclosures and aluminium profile frames
- Low-clearance access doors and inspection hatches on food, bakery and packaging machinery
- Lids and doors on ovens, provers, warming cabinets and dryers up to +180°C
- Panel and glazing infill strips in slotted frames (80 Shore A)
- Air handling units, fan coil housings and ductwork panels
- Outdoor enclosures and marine hatches, where UV and ozone crack other rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | 40 Shore A | 80 Shore A | Test method |
|---|---|---|---|
| Dimensions (identical for both hardnesses) | |||
| Profile type | Solid T section, square-cut flat head, centred leg | – | |
| Overall height | 5.2 mm | – | |
| Head width | 6.0 mm | – | |
| Head thickness | 2.0 mm | – | |
| Leg width (base thickness) | 3.2 mm | – | |
| Leg length below head | 3.2 mm (reference, 5.2 − 2.0) | – | |
| Shoulder each side | 1.4 mm (reference, leg centred) | – | |
| Suits slot | Approx. 3.0–3.2 mm wide, at least 3.2 mm deep | – | |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 | |
| Length per coil | 25 m, one continuous length | – | |
| Material and physical properties | |||
| Compound | Solid silicone rubber | – | |
| Hardness | 40 Shore A | 80 Shore A | DIN ISO 48-4 |
| Density | 1.12 g/cm³ | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 9.6 N/mm² (9.6 MPa) | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 770 % | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 36 % after 22 h at 175 °C | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 56 % | 54 % | ISO 4662 |
| Service conditions | |||
| Working temperature | -50 °C to +180 °C | – | |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – | |
| Supply | |||
| Colours | Black, white, translucent, red, green, blue, yellow | – | |
| Approx. weight (calculated from 22.2 mm² section and density) | About 25 g per metre, 0.62 kg per coil | About 27 g per metre, 0.67 kg per coil | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – | |
| Our part numbers | IP-SITS-6X5.2-40-25M-<colour> | IP-SITS-6X5.2-80-25M-<colour> | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile, in both hardnesses. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 3.2mm wide, so it grips best in a slot of about 3.0–3.2mm. The slot should be at least 3.2mm deep so the head can sit down flat; a deeper slot is fine. The 80 Shore A leg is stiff, so it needs a slot close to 3.2mm; the soft 40 Shore A leg will squeeze into a slightly tighter one.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. A drop of soapy water helps the 80 Shore A version slide in.
- Lay the seal into corners rather than pulling it round them. Stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 3.0–3.2mm wide and at least 3.2mm deep. The head is 6mm wide, so it overlaps the slot by 1.4mm each side and covers the edges.
Which way up does it go?
The 3.2mm leg goes into the slot, and the wider, flat head sits on the surface, facing the door, lid or panel it seals against.
Is the profile different between 40 and 80 Shore A?
No. Both have exactly the same 6mm × 5.2mm shape and dimensions. Only the compound changes: 40 Shore A is soft and squashes easily, 80 Shore A is firm and stiff.
Can it be used near ovens and heaters?
Both versions are rated to +180°C continuous. That suits oven and warming-cabinet doors, drying equipment and heater housings, as long as the seal itself stays at or below that temperature. It stays flexible down to -50°C.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
The 40 Shore A version has a compression set of 36% after 22 hours at 175°C, so it springs back well through repeated heat cycles. The 80 Shore A version measures 78% on the same test, so under constant hot compression it takes a set; use it where stiffness and wear resistance matter more than recovery.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, use a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour and hardness the same price?
Yes. All 14 options cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 5.5mm x 4.5mm (another low-profile T seal)
- Silicone T Seal Profile – 5mm x 5.9mm
- Silicone L Profile – 6.2mm x 5.2mm (for edges and corners rather than slots)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-6X5.2-40-25M-BLK |
|---|---|
| Weight | 1.54 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6mm x 5.2mm – 40 or 80 Shore A – 25m Coil