
Rubber & FoamSKU IP-TPECB-10X9-STD
White TPE Compact Bead – Food Contact Grade – 10mm x 9mm for 6–7.5mm Gaps – 50m Coil
A small, soft, white hollow bead for hygienic areas. The 8mm round bulb sits on a 10mm self-adhesive base and squashes down to close gaps of 6mm to 7.5mm, while also cushioning knocks on doors, guards and panels. It is extruded from a single 40° Shore A TPE compound that the supplier states complies with FDA and CE specifications for food contact. Supplied as one continuous 50m coil, ready for same-day dispatch.
At a glance
- Size: 10mm wide x 9mm high, 8mm diameter hollow bulb
- Seals: gaps (clearance) of 6mm to 7.5mm
- Fixing: factory-applied adhesive strip with peel-off liner, no screws or sealant
- Material: soft solid TPE, 40° Shore A, white so dirt shows up straight away
- Food contact: supplier states FDA and CE food-contact compliance
- Temperature: -50°C to +90°C per datasheet (keep to +75°C for continuous duty)
- Coil: 50m continuous, works out at £14.56 per metre
Technical drawing

Specifications
| Property | Value | Basis / test method |
|---|---|---|
| Overall size (W x H) | 10mm x 9mm | Supplier drawing, nominal |
| Base width | 10mm | Supplier drawing, nominal |
| Overall height (excluding adhesive) | 9mm | Supplier drawing, nominal |
| Bulb outside diameter | 8mm, hollow | Supplier drawing, nominal |
| Bore / wall thickness | Not published | Ask us if you need it |
| Clearance to fill (gap it seals) | 6mm to 7.5mm | Supplier rating |
| Bending radius (fitted) | 100mm to 150mm round corners | Supplier datasheet sketch, indicative |
| Material | TPE (thermoplastic elastomer), single compound, solid (not foam) | Supplier technical data |
| Hardness | 40° Shore A | Supplier technical data and drawing (Shore A). The PDF datasheet prints "40 Shore D", which conflicts with the drawing; we follow the drawing |
| Service temperature | -50°C to +90°C (datasheet); +75°C maximum in the supplier's technical table | Supplier rating. Use +75°C as the continuous limit |
| Weight | 41g per metre (about 2.05kg per 50m coil) | Supplier technical data |
| Fixing | Self-adhesive strip with release liner | Supplier description |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section) / L2 (length) | ISO 3302-1 |
| Colour | White | - |
| Coil length | 50m continuous | - |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile | Ask us if your specification needs them |
Materials and compliance
The bead is a single soft TPE (thermoplastic elastomer) compound, extruded solid with a hollow core. The supplier states in writing that it complies with CE and FDA specifications for food contact and that it is produced in a clean environment for food-handling areas. The supplier also states the material is 100% recyclable and resists weathering and chemical attack from routine cleaning.
No other approval (such as a specific EC 1935/2004 declaration, WRAS, REACH, RoHS or fire rating) is stated for this profile, so we do not claim one. If your audit needs a declaration of conformity, contact us before ordering. Note that the food-contact statement covers the TPE profile; the adhesive strip is for bonding to the mounting surface and should not be the food-contact face.
Typical uses
- Soft closing seal on hatches, inspection doors and cabinet doors in food and drink production
- Impact and knock protection on stainless steel guards, panels and machine frames
- Dust and splash seal on enclosures in clean and hygienic areas
- Small doors and windows on cold rooms, display units and catering equipment
- Surface protection where a white, easy-to-inspect seal is needed (labs, medical and pharma)
Which one do I need?
| Profile | Suits |
|---|---|
| TPE compact bead 10mm x 9mm (this item) | 6mm to 7.5mm gaps, stick-on, white food-contact TPE, 50m coil |
| White TPE P profile 30mm x 15mm | Larger gaps, where a flange can be clamped or bonded |
| White TPE P profile 38mm x 16mm | Larger doors needing a bigger bulb |
| Silicone P extrusion 25mm x 12mm | Hotter areas, where silicone's higher temperature rating is needed |
How much do I need?
Measure the perimeter of every opening you want to seal. For example, ten 600mm x 400mm hatch doors sealed all round need 10 x 2.0m = 20m, so one 50m coil covers them with plenty spare. Allow a few centimetres per run so the ends can butt tightly.
Fitting
- Clean the mounting surface with an alcohol wipe and let it dry fully. Grease and cleaning residue are the main cause of poor adhesion.
- Check the gap with the door closed: it should be 6mm to 7.5mm where the bead will sit.
- Fit above about +10°C if you can. Peel back a short length of liner, place the bead and press it down firmly.
- Keep peeling and pressing along the run. Do not stretch the bead as you go, or it will shrink back and open the joint.
- Go round corners in a smooth curve (about 100mm to 150mm radius) rather than a sharp bend, so the bulb does not kink.
- Cut the end square with a sharp knife or scissors and butt it tight to the start.
Frequently asked questions
What gap does it seal?
It is designed for a 6mm to 7.5mm gap. The 9mm bead then compresses by about 1.5mm to 3mm, enough to seal without making the door hard to close. For bigger gaps, look at the white TPE P profiles above.
Is it food safe?
The supplier states the TPE complies with CE and FDA specifications for food contact, and it is white so contamination is easy to spot. Mount it with the adhesive face against the frame, not against food. If you need a formal declaration for an audit, contact us before ordering.
How do I fit it?
Clean and dry the surface, peel the liner and press the bead on. No screws, clips or sealant are needed. See the fitting steps above.
What temperatures can it take?
The supplier's datasheet gives -50°C to +90°C, and its technical table gives a +75°C maximum. Treat +75°C as the continuous limit. It is fine in chillers and freezers, but not near ovens or steam outlets. For hotter spots, use silicone.
How do I cut and join it?
Cut it square with a sharp knife or heavy scissors. Butt the two ends tightly; no joining compound is needed for most door seals. For a fully sealed joint in a wash-down area, a small amount of food-safe silicone sealant can be applied to the butt joint.
Will it go round corners?
Yes. It is soft and flexible, so it follows curves and corners. Use a smooth radius of about 100mm to 150mm rather than a sharp 90° bend, so the hollow bulb stays round.
Can it be washed down?
Yes. TPE handles water, weather and routine cleaning chemicals well, and the smooth white surface is easy to wipe. Avoid long soaking in strong solvents or oils without testing first.
Can I buy a shorter length?
This listing is for a full 50m coil. For a smaller quantity, contact us.
Data sheet
Download the technical data sheet (PDF)
Need help choosing? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk with your gap size and application.
Product details
| SKU | IP-TPECB-10X9-STD |
|---|---|
| Weight | 5.07 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:White TPE Compact Bead – Food Contact Grade – 10mm x 9mm for 6–7.5mm Gaps – 50m Coil