
Rubber & FoamSKU IP-TPEP-20X8-B19A-STD
White TPE P Seal – Food Contact Grade – 20mm x 8mm – Soft 40° Shore A – 25m Coil
A soft, white, food-contact P seal for indoor doors, hatches and enclosures. The 8 × 8 mm hollow D-bulb is made from 40° Shore A thermoplastic elastomer (TPE), so it closes with very little force. The flat 20 mm flange gives a wide area for bonding or clamping. It comes as one continuous 25 m coil that you cut to length on site.
- Food contact: the supplier states the compound is FDA-approved and suitable for contact with foodstuffs.
- Soft and low-force: 40° Shore A with a 565% elongation at break, so it suits light doors and lids that should not need slamming.
- Wide temperature range: −50 °C to +90 °C, from blast chillers to proving cabinets.
- Non-marking white: leaves no black marks on stainless or painted surfaces.
- Indoor use only: this grade is not UV-stable. For outdoor work, choose an EPDM or silicone P seal.
- 100% recyclable thermoplastic material.
Technical drawing

Specification
| Property | Value | Source / test method |
|---|---|---|
| Profile type | P seal: hollow D-bulb with a flat flange on one side | Supplier drawing |
| Overall width | 20 mm | Supplier drawing |
| Overall height (bulb) | 8 mm | Supplier drawing |
| Bulb width | 8 mm | Supplier drawing |
| Wall and flange thickness | 1.5 mm | Supplier drawing |
| Flat flange beyond the bulb | ≈ 12 mm | Derived: 20 mm − 8 mm |
| Hollow bore | ≈ 5 × 5 mm, arched top | Derived: 8 mm − 2 × 1.5 mm wall |
| Material | Thermoplastic elastomer (TPE) | Supplier datasheet |
| Colour | White | Supplier listing |
| Hardness | 40 Shore A | Supplier datasheet (Shore A durometer; method not stated) |
| Tensile strength | 4.8 MPa | Supplier datasheet (method not stated) |
| Elongation at break | 565 % | Supplier datasheet (method not stated) |
| Density | 1.08 g/cm³ | Supplier datasheet (method not stated) |
| Compression set | 54 % after 24 h at 70 °C | Supplier datasheet (method not stated) |
| Tear strength | Not published for this grade | Ask us if you need it |
| Working temperature | −50 °C to +90 °C | Supplier datasheet |
| UV / outdoor use | Not UV-stable: indoor use only | Supplier listing |
| Weight | 0.065 kg per metre (≈ 1.6 kg per 25 m coil) | Supplier listing; coil weight calculated |
| Dimensional tolerance | Not stated for this grade | Ask us for the tolerance class before close-fit work |
| Supplied length | 25 m continuous coil | Supplier listing |
| Part number | IP-TPEP-20X8-B19A-STD | Industrial Polymers |
Materials and compliance
- FDA: the supplier states this P seal is made from an FDA-approved TPE compound that is suitable for contact with foodstuffs.
- Recyclability: the material is stated to be 100% recyclable.
- Not claimed: the supplier does not state EC 1935/2004, WRAS, REACH or RoHS compliance for this product in text, so we make no such claim. Contact us if your audit needs a declaration of conformity.
- UV: this compound is not UV-stable. Keep it out of direct sunlight.
How it fits
Bond or clamp the flat flange to the frame so the bulb sits where the door or lid closes onto it. For a good seal, size the closed gap so the bulb is squeezed by about a third. That is a closed gap of roughly 5 to 6.5 mm.

- Clean the mounting face with isopropyl alcohol and let it dry before bonding.
- Cut it with a sharp knife or rubber shears against a straight edge, so the ends are square.
- Lay the seal in without stretching it. Stretched TPE shrinks back and opens gaps at the corners.
- At corners, mitre the flange or notch it so the bulb turns the corner without kinking.
Which 20 × 8 mm white TPE P seal?
| This seal (40° Shore A) | Firmer grade (60° Shore A) | |
|---|---|---|
| Hardness | 40° Shore A: soft, low closing force | 60° Shore A: firmer, more wear-resistant |
| Wall / flange | 1.5 mm | 1 mm |
| Minimum temperature | −50 °C | −40 °C |
| Best for | Light doors, lids, hatches, chillers | Heavier doors and frequently used panels |
Data sheet
Download the summary data sheet (PDF). The full test values are in the table above.
Questions
Can I use this seal outdoors?
No. This TPE grade is not UV-stable and will break down in sunlight. Use it indoors only. For outdoor doors, choose an EPDM or silicone P seal.
What gap does it seal?
The bulb is 8 mm tall. It works best with a closed gap of about 5 to 6.5 mm, which squeezes the bulb by around a third. Below about 4.5 mm the bulb flattens fully and the door may not close easily.
Is it safe for food areas?
The supplier states that the compound is FDA-approved and suitable for contact with foodstuffs. Typical uses are food processing equipment, ingredient bins, proving cabinets and chillers.
How hot or cold can it go?
The working range is −50 °C to +90 °C. It is fine for freezers and warm proving cabinets, but not for ovens or anything steam-cleaned above 90 °C. For those, use a silicone P seal.
How do I fix it in place?
Bond the 20 mm flange with an adhesive or double-sided acrylic tape rated for TPE, or trap it under a clamp strip or rivets. TPE is a low-energy surface, so use a primer or test the adhesive first.
Can it be cut and joined?
Yes. It cuts cleanly with a sharp knife. Being thermoplastic, its ends can be heat-welded with a hot plate into a continuous loop, or butt-joined with a cyanoacrylate glue suitable for TPE.
Why choose 40 Shore A over the 60 Shore A version?
The softer bulb needs less force to compress. That suits light lids and hatches, and doors with self-closers. The 60° grade resists wear better on heavy, high-traffic doors.
How much do I get, and is it in stock?
Each coil is one continuous 25 m length, about 1.6 kg. It is held in stock for dispatch. See the delivery message above for today's cut-off.
Need a different size, a cut length or a declaration for your audit? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEP-20X8-B19A-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:White TPE P Seal – Food Contact Grade – 20mm x 8mm – Soft 40° Shore A – 25m Coil