
Rubber & FoamSKU IP-EPDMS-10X5-14M
EPDM Sponge Half Round Seal – 10mm x 5mm – 14m to 30m Lengths
Price shown updates with the option you pick.
A soft, solid half-round seal in black EPDM sponge, 10 mm wide and only 5 mm high, cut in one continuous length from 14 m up to a full 30 m coil. The flat 10 mm back bonds down with adhesive, and the rounded crown squashes flat when a lid, panel or door closes on it. That makes a low, neat air and water seal that also cushions light knocks.
At a glance
- Size: 10 mm wide × 5 mm high, solid half round (R 5 mm crown), no hollow core
- Fixing: plain flat back; bond it with a rubber-compatible contact or instant adhesive
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO, 20 g per metre
- Temperature: -40 °C to +115 °C
- Outdoors: ozone, weather and UV resistance rated excellent; absorbs no more than 5% water
- Lengths: 14 m to 30 m in one piece, all at £12.15 per metre inc VAT
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Low-profile lid and door seals on electrical enclosures, control boxes and cabinets
- Glazing, closure and weather strips where only a 3 to 4 mm gap is available
- Seals on vehicle, trailer and caravan hatches and access panels
- Soft bump and impact strip along panel edges, shelves and equipment
- Expansion-joint infill and light anti-vibration packing
- Gasket strip on electronics housings and instrument covers
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Solid half round on a flat base (no hollow core) | Manufacturer's profile drawing |
| Overall width (across the flat base) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to crown) | 5.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Crown radius | R 5 mm | Follows from 10 mm width and 5 mm height of a true half round; not separately stated |
| Bonding face | Flat, 10 mm wide, plain (no adhesive tape) | Manufacturer recommends fixing with a suitable adhesive |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 20 g/m (0.02 kg per metre): about 0.28 kg for 14 m, 0.6 kg for 30 m | Manufacturer product page and datasheet |
| Service temperature | -40 °C to +115 °C | Manufacturer product page (minimum and maximum temperature) |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Compression set | 25% maximum (after 24 h recovery) | Manufacturer datasheet; test temperature and standard not stated |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied lengths | One continuous piece, 14 m to 30 m (30 m = full coil) | - |
| Price per metre | £12.15/m inc VAT at every length | - |
The manufacturer's datasheet mentions a 50 m coil; its product page gives a 30 m full coil, which is the longest single piece we supply. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes it as air and watertight and resistant to heat, ozone, weathering, steam, ketones and dilute acids and alkalis, with good electrical insulating properties. Like all EPDM it is not suited to oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be under 5 mm so the dome is squeezed. About 3 to 4 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The face you bond to should be flat and at least 10 mm wide.
- Clean and dry. Wipe both surfaces with isopropyl alcohol and let them dry. Check your adhesive suits the frame material.
- Bond the back. Apply a thin, even film of contact or rubber-compatible instant adhesive and press the strip down along its length. Do not stretch it, or it will shrink back and open gaps.
- Corners and joins. It bends round gentle corners; for tight corners cut and butt the ends, or mitre them. Glue the ends together for a fully sealed join.
How much do I need?
Add up every edge you want to seal and allow about 5% for trimming. A 600 × 400 mm enclosure lid takes 2 m, so 14 m does seven lids. Choose the length you need; each one comes as a single continuous piece.

Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge half round (this item) | 10 × 5 mm | Closed gaps of about 3 to 4 mm, solid section |
| EPDM sponge crown strip | 10 × 5 mm | Same footprint on a 100 m coil |
| EPDM sponge half round | 12.5 × 6.25 mm | Closed gaps of about 4 to 5 mm |
| EPDM sponge D section | 8 × 10 mm | Larger gaps (6 to 8 mm), hollow, self-adhesive |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
Is the price per metre or per length?
Per length. Pick 14 m to 30 m from the Length menu; each is one continuous piece priced at £12.15 per metre inc VAT. 30 m is a full coil.
Why is the minimum 14 m?
It is cut from a continuous coil, and 14 m is the shortest length we cut. Any spare keeps well in a cool, dark place.
What gap will it seal?
Any closed gap under its 5 mm height. Aim for 3 to 4 mm. For gaps of 4 to 5 mm the 12.5 × 6.25 mm half round is a better fit; for 6 to 8 mm use the 8 × 10 mm D section.
Is it self-adhesive?
No. The back is plain sponge, so you can choose an adhesive to suit the surface. A contact adhesive or a rubber-compatible instant adhesive works well on metal, wood and most rigid plastics.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly; for a fully sealed join, glue the ends together with instant adhesive.
Will it go round corners?
Yes, it bends easily round gentle curves. For sharp 90° corners cut and butt the strip or mitre it, so it does not lift.
What temperatures can it take?
The manufacturer gives -40 °C to +115 °C, and it passes a -40 °C flexibility test.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent and mould resistance as very good.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well, but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-10X5-14M |
|---|---|
| Weight | 0.84 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Half Round Seal – 10mm x 5mm – 14m to 30m Lengths