
Rubber & FoamSKU IP-EPDM-10X5-STD
EPDM Sponge Crown Strip – 10mm x 5mm, Self-Adhesive – 100m Coil
A low-profile black EPDM sponge seal, 10 mm wide and only 5 mm high, with a peel-and-stick adhesive base. One continuous 100 m coil. Two rounded crowns and a lower centre rib press flat when a lid, hatch or door closes on them, giving three sealing lines across the face. Use it where there is little room for a seal, or as a soft, discreet bump strip on panel edges.
At a glance
- Size: 10 mm wide × 5 mm high; 2.5 mm crowns, 4 mm at the groove floor
- Fixing: factory-applied adhesive backing with a peel-off liner; sticks to clean metal, plastic, wood and rubber
- Material: solid expanded (sponge) EPDM, very soft at 40° Shore OO, non-marking
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Coil: 100 m continuous length, black, about £2.35 per metre
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Lid and door seals on electrical enclosures, control boxes, equipment cases and cabinets
- Draught and dust strips on light doors, hatches, access panels and glazed closures
- Low-profile weather strips on vehicles, trailers, caravans and boats
- Anti-rattle and vibration pads between panels, covers and housings
- Soft, discreet impact protection on edges, shelving and display fittings
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Solid crown strip: two rounded outer crowns and a low centre rib on a flat, self-adhesive base | Manufacturer's profile drawing |
| Overall width (across the base) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to top of crowns) | 5.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Height at the groove floor | 4.0 mm (grooves about 1 mm deep) | Manufacturer's profile drawing |
| Crown width (each outer crown) | 2.5 mm | Manufacturer's profile drawing |
| Centre rib | Lower than the crowns; height not stated | Manufacturer's profile drawing (shape only) |
| Fixing | Factory-applied adhesive backing with peel-off liner | Adhesive type and thickness not stated by the manufacturer |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 14 g/m (technical table) to 20 g/m (product summary and datasheet): about 1.4 to 2.0 kg per 100 m coil | Manufacturer figures; the sources differ |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | 100 m continuous coil | - |
| Price per metre | About £2.35/m inc VAT (£235.41 per 100 m coil) | - |
The manufacturer gives two weights (14 g/m and 0.02 kg/m) and two compression-set figures for this part; both are shown above. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (sponge) EPDM with a factory-applied adhesive backing. The manufacturer describes the profile as non-marking, air and watertight, and resistant to ozone, weather, heat, steam, ketones and dilute acids and alkalis. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It should be smaller than 5 mm so the crowns are squeezed. About 3 to 4 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The flat face you stick to should be at least 10 mm wide.
- Clean and dry. Wipe with isopropyl alcohol and let it dry. Fit above about 10 °C for the best bond.
- Peel and press. Peel the liner a short way at a time and press the base down firmly along its length. Do not stretch the strip or it will shrink back.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
Which size do I need?
| Profile | Size (W × H) | Supplied as |
|---|---|---|
| EPDM sponge crown strip (this item) | 10 × 5 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip | 15 × 4 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip | 14.5 × 7.5 mm | 50 m coil |
| EPDM sponge half round | 10 × 5 mm | Per metre |
| EPDM sponge D section (hollow) | 8 × 10 mm | 50 m coil, self-adhesive |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
Is the price per metre or per coil?
Per coil. One unit is a complete 100 m continuous coil, which works out at about £2.35 per metre.
What gap will it seal?
Closed gaps below its 5 mm height; aim for about 3 to 4 mm. For gaps of 5 to 7 mm choose the 14.5 × 7.5 mm crown strip, and for 6 to 8 mm the hollow 8 × 10 mm D section, which closes with less force.
How do I fit it?
Clean the surface with isopropyl alcohol, peel back the liner a little at a time and press the flat base down firmly. Do not stretch it as you go.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly together; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Why the crowns and grooves rather than a flat strip?
The two crowns and centre rib each make a line of contact, so the strip seals with less closing force than a flat foam tape of the same size, and the grooves give the sponge room to spread as it is squeezed.
Will it mark painted surfaces?
The manufacturer states it is non-marking.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDM-10X5-STD |
|---|---|
| Weight | 4.41 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Crown Strip – 10mm x 5mm, Self-Adhesive – 100m Coil