
Rubber & FoamSKU IP-TPEE-15.5X13.2-25M
Black TPE Expansion Joint Seal – 15.5mm x 13.2mm – 25m Coil
A black TPE expansion joint seal for 10 mm to 12.5 mm wide joints. The 11.7 mm flat cap gives a level, low-profile top that wheels and feet roll straight over, and two pairs of flexible fins grip the joint walls below. The 5 mm central stem has two hollow chambers, so the seal squeezes as the joint closes and recovers as it opens. It is 15.5 mm across the lower fins and 13.2 mm deep overall. Supplied as a continuous 25 m coil (£23.36 per metre inc VAT), held in stock in the UK.
At a glance
- Fits joints 10–12.5 mm wide: fins 15.5 mm tip to tip are squeezed into the gap and hold it in by friction, with no adhesive needed
- Flat 11.7 mm cap: laps the joint edges in joints up to about 11.5 mm and sits flush inside wider ones, so it is not a trip hazard
- Twin hollow chambers in the stem let the seal follow joint movement without tearing
- TPV (PP/EPDM) thermoplastic rubber, 70–72 Shore A, working range −50 °C to +90 °C
- Resistant to weathering and UV, light (80 g/m), and cuts cleanly with a sharp knife
Technical drawing

Specification
| Property | Value | Test method / source |
|---|---|---|
| Overall width (across lower fins, free state) | 15.5 mm | Supplier drawing |
| Overall height (cap top to foot) | 13.2 mm | Supplier drawing |
| Cap width (visible top face) | 11.7 mm | Supplier drawing |
| Body height below the cap | 12.3 mm | Supplier drawing |
| Cap thickness | ≈0.9 mm (13.2 − 12.3) | Derived from the drawing |
| Joint / groove width it fits | 10 mm min – 12.5 mm max | Supplier data |
| Joint depth needed | at least ≈12.5 mm (≈13.5 mm where the cap sits inside a joint wider than 11.7 mm) | Derived from the 12.3 mm body height |
| Cross-section | Flat cap, central stem with 2 hollow chambers, 2 pairs of angled fins, small locating foot | Supplier drawing |
| Material | Thermoplastic elastomer, TPV type (PP/EPDM) | Supplier datasheet |
| Colour | Black | – |
| Hardness | 70–72 Shore A (product page 70°, datasheet 72°) | ISO 868 |
| Density (specific gravity) | 0.97 g/cm³ | ASTM D792 / ISO 1183 |
| Tensile strength | 7.4 MPa | ASTM D412 / ISO 37 |
| Elongation at break | 450 % | ASTM D412 / ISO 37 |
| Compression set, 22 h at 70 °C | 30 % | ASTM D395 B / ISO 815 |
| Compression set, 70 h at 125 °C | 41 % | ASTM D395 B / ISO 815 |
| Tear strength | Not published for this profile | – |
| Working temperature | −50 °C to +90 °C | Supplier datasheet |
| Weight | 80 g per metre (≈2.0 kg per 25 m coil) | Supplier data |
| Dimensional tolerance | ISO 3302-1:2014 class E2 (cross-section); L2 quoted for length | ISO 3302-1 |
| Supplied as | 25 m continuous coil | – |
| Price per metre | £23.36 inc VAT (£583.95 per 25 m coil) | – |
Materials and compliance
The seal is extruded from a TPV, a thermoplastic vulcanisate made of polypropylene with cross-linked EPDM rubber. The EPDM gives the fins rubber-like recovery and weather and UV resistance. The polypropylene makes it light (SG 0.97), clean to cut and recyclable as a thermoplastic.
Approvals: the manufacturer does not state any approvals for this profile in its written specification, so we make no FDA, food-contact, WRAS, REACH or RoHS claim. If your project needs a declaration, ask us before ordering and we will request it.
How it fits

- Check the joint is 10–12.5 mm wide along its whole length, and at least about 12.5 mm deep.
- Brush and blow out dust, grit and loose concrete. The fins grip best on clean, sound arrises.
- Start at one end with the flat cap facing up. Push the foot and lower fins into the joint, then press the cap down until it is level with the surface. A rubber mallet or a wooden block helps.
- Work along the joint a short length at a time. Do not stretch the seal as you go, or it will shrink back and open gaps at the ends.
- Cut to length with a sharp knife, leaving 1–2 mm extra so the ends butt tightly.

Where it is used
- Movement joints in multi-storey and underground car park decks
- Joints between precast concrete panels, walls and slabs
- Bridge decks and walkways with small joints
- Roof and podium joints, tunnels and service ducts
- Water and wastewater treatment plants, plant rooms and loading areas
Questions
What joint width does it fit?
Joints from 10 mm to 12.5 mm wide. Below 10 mm the fins cannot fold far enough to go in. Above 12.5 mm they do not grip the walls hard enough to hold the seal down. Measure the narrowest and widest points of the joint before ordering.
Does it need adhesive?
No. The angled fins act like barbs: they flex upwards as you push the seal in and dig into the joint walls if anything tries to pull it out. On joints that see heavy traffic or water pressure, you can add a polyurethane or MS-polymer sealant bead along the arrises for extra security.
Can vehicles drive over it?
Yes, as long as the joint is within the 10–12.5 mm range. The low flat cap stays level with the surface, which is why it suits car park decks. Tracked plant or steel-wheeled trolleys can damage any elastomer seal, so protect it during construction.
Is it suitable outdoors and in cold weather?
Yes. The TPV material is rated from −50 °C to +90 °C and resists weathering and UV, so it stays flexible through a UK winter and on sun-exposed decks.
How do I cut and join it?
Cut square with a sharp knife or fine-toothed saw. Butt the ends tightly, leaving 1–2 mm extra so they press together. At corners, mitre the cap at 45°. For a permanent bond, TPV can be heat-welded or joined with a cyanoacrylate made for polyolefins (use a primer).
Is it watertight?
It keeps out water, dirt and debris in normal use, but it is a compression seal, not a hydrostatic waterstop. For joints under constant water pressure, use it as the visible top seal over a proper waterstop or sealant system.
How much movement can it take?
It works across the full 10–12.5 mm joint range, so it takes about 2.5 mm of opening and closing between those limits. The hollow stem means the cap stays level while the fins flex.
How is it supplied and how fast is dispatch?
As one continuous 25 m coil (about 2 kg). It is held in stock, and orders placed by the cut-off on our dispatch message ship the same day.
Need help choosing a profile for your joint? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Related products
- Black TPE Expansion Joint Seal – 16mm x 18mm – 25m Coil (for wider joints)
Product details
| SKU | IP-TPEE-15.5X13.2-25M |
|---|---|
| Weight | 4.85 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black TPE Expansion Joint Seal – 15.5mm x 13.2mm – 25m Coil