
Rubber & FoamSKU IP-TPEE-16X18-STD
Black TPE Expansion Joint Seal – 16mm x 18mm – 25m Coil
A solid black TPE expansion joint seal for movement joints 9 mm to 11 mm wide. The 16 mm cap sits on the surface and laps both joint edges, while two pairs of angled fins on a solid 4 mm stem grip the joint walls below, so it pushes in by hand and resists pulling out. It is 18 mm deep overall and 13 mm across the fin tips. Supplied as one continuous 25 m coil (£23.76 per metre inc VAT), held in stock in the UK.
At a glance
- Fits joints 9–11 mm wide: the 13 mm fin span is squeezed into the gap and holds by friction, with no adhesive needed in most joints
- 16 mm twin-wing cap covers the joint arrises and keeps out grit, water and debris
- Solid body, not hollow: rigid enough for foot and vehicle traffic over small joints
- TPV (PP/EPDM) thermoplastic rubber, 70–72 Shore A, rated −50 °C to +90 °C
- Weather and UV resistant, 141 g per metre, cuts cleanly with a sharp knife
Technical drawing

Specification
| Property | Value | Test method / source |
|---|---|---|
| Cap width (overall width) | 16 mm | Supplier drawing |
| Overall height (cap top to foot) | 18 mm | Supplier drawing |
| Width across fin tips (free state) | 13 mm | Supplier drawing |
| Foot width | 4 mm | Supplier drawing |
| Stem width | ≈4.2 mm | Measured from the drawing |
| Cap thickness at the wings | ≈2.5 mm | Measured from the drawing |
| Joint / groove width it fits | 9 mm min – 11 mm max | Supplier data |
| Joint depth needed | at least ≈16 mm | Derived from the drawing (depth below the cap) |
| Cross-section | Solid: twin-wing cap, central stem, 2 pairs of angled fins, flat foot | Supplier drawing |
| Material | Thermoplastic elastomer, TPV type (PP/EPDM) | Supplier datasheet |
| Colour | Black | – |
| Hardness | 70–72 Shore A (product page 70°, datasheet 72°) | ISO 868 |
| Density (specific gravity) | 0.97 g/cm³ | ASTM D792 / ISO 1183 |
| Tensile strength | 7.4 MPa | ASTM D412 / ISO 37 |
| Elongation at break | 450 % | ASTM D412 / ISO 37 |
| Compression set, 22 h at 70 °C | 30 % | ASTM D395 B / ISO 815 |
| Compression set, 70 h at 125 °C | 41 % | ASTM D395 B / ISO 815 |
| Tear strength | Not published for this profile | – |
| Working temperature | −50 °C to +90 °C | Supplier datasheet |
| Weight | 141 g per metre (≈3.5 kg per 25 m coil) | Supplier data |
| Dimensional tolerance | ISO 3302-1:2014 class E2 (cross-section); L2 quoted for length | ISO 3302-1 |
| Supplied as | 25 m continuous coil | – |
| Price per metre | £23.76 inc VAT (£594.00 per 25 m coil) | – |
Materials and compliance
The seal is extruded from a TPV, a thermoplastic vulcanisate of polypropylene with cross-linked EPDM rubber. The EPDM phase gives the fins rubber-like recovery and good resistance to weather, ozone and UV; the polypropylene keeps it light (SG 0.97), clean-cutting and recyclable as a thermoplastic.
Approvals: the manufacturer's written specification does not state any approvals for this profile, so we make no FDA, food-contact, WRAS, REACH or RoHS claim. If your project needs a declaration, ask us before ordering and we will request it.
How it fits

- Check the joint is 9–11 mm wide along its whole length and at least about 16 mm deep.
- Brush and blow out dust, grit and loose concrete so the fins bite on clean, sound arrises.
- Start at one end with the cap facing up. Feed the foot and fins into the joint and press the cap down until it rests on both edges. A rubber mallet or wooden block helps in tight joints.
- Work along a short length at a time without stretching the seal, or it will shrink back and open gaps at the ends.
- Cut to length with a sharp knife, leaving 1–2 mm extra so the ends butt tightly.
Where it is used
- Movement joints in multi-storey and underground car park decks
- Joints between precast concrete panels, walls and floor slabs
- Small joints in bridge decks, walkways and podiums
- Roof joints, tunnels and service ducts
- Water treatment plants, plant rooms and loading areas
Questions
What joint width does it fit?
Joints from 9 mm to 11 mm wide. Narrower than 9 mm and the fins cannot fold far enough to go in; wider than 11 mm and they no longer grip hard enough to hold the seal down. Measure the narrowest and widest points of the joint before ordering.
How deep does the joint need to be?
At least about 16 mm, so the stem and foot fit fully below the cap. The cap itself (about 2.5 mm thick) sits on top of the surface.
Does it need adhesive?
Not usually. The angled fins work like barbs: they fold up as the seal goes in and dig into the joint walls if anything tries to pull it out. On joints with heavy traffic or standing water you can add a bead of polyurethane or MS-polymer sealant along the edges for extra security.
Can vehicles drive over it?
Yes, within the 9–11 mm range. The body is solid rather than hollow, so it supports the cap under wheels. Tracked plant and steel-wheeled trolleys can damage any elastomer seal, so protect it during construction.
Is it suitable outdoors and in frost?
Yes. The TPV material is rated from −50 °C to +90 °C and resists weathering and UV, so it stays flexible through winter and on sun-exposed decks.
How do I cut and join it?
Cut square with a sharp knife or fine-toothed saw and butt the ends tightly. Mitre the cap at 45° at corners. For a permanent joint, TPV can be heat-welded, or bonded with a cyanoacrylate made for polyolefins used with a primer.
Is it watertight?
It keeps out water, dirt and debris in normal use, but it is a compression seal, not a hydrostatic waterstop. Under constant water pressure, use it as the visible top seal over a proper waterstop or sealant.
How is it supplied and how fast is dispatch?
As one continuous 25 m coil, about 3.5 kg. It is held in stock and orders placed before the cut-off on our dispatch message ship the same day.
Data sheet
Download the technical data sheet (PDF)
Need help choosing a profile for your joint? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Related products
Product details
| SKU | IP-TPEE-16X18-STD |
|---|---|
| Weight | 7.94 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black TPE Expansion Joint Seal – 16mm x 18mm – 25m Coil