
Rubber & FoamSKU IP-TPEP-20X8-STD
Black TPE P Profile Seal – 20mm Flange x 8mm Hollow Bead – 25m Coil
A black TPE P profile with a flat 20 mm fixing flange and a thin-walled 8 mm hollow bead. The 1 mm wall and 6 mm bore make the bead very easy to compress, so it closes small gaps on hatches, enclosure lids, cabinet doors and glazed panels where only light closing pressure is available. Supplied as one continuous 25 m coil, held in UK stock.
At a glance
- Size: 20 mm overall width, Ø8 mm bead outside, Ø6 mm bore, 1 mm flange and wall
- Material: thermoplastic elastomer (TPE), black, non-marking
- Hardness: 60 Shore A (product listing); the manufacturer's datasheet quotes 70 Shore A
- Temperature: −40 °C to +90 °C (datasheet: −35 °C to +90 °C)
- Length: 25 m continuous coil, works out at about £18.41 per metre
- Waterproof, lightweight, easy to cut with a sharp knife, recovers its shape after repeated closing
Technical drawing

Specification
| Property | Value | Unit | Test method / source |
|---|---|---|---|
| Profile | P section: flat flange with round hollow bead | – | Manufacturer drawing |
| Overall width (flange incl. bead) | 20 | mm | Manufacturer drawing |
| Bead outside diameter (free height) | 8 | mm | Manufacturer drawing |
| Bead bore (inside diameter) | 6 | mm | Manufacturer drawing (Ø6 x 8) |
| Bead wall thickness | 1 (derived: (8 − 6) ÷ 2) | mm | Calculated from drawing |
| Flange thickness | 1 | mm | Manufacturer drawing / data |
| Flat flange beyond the bead | 12 (derived: 20 − 8) | mm | Calculated from drawing |
| Coil length | 25 | m | – |
| Material | Thermoplastic elastomer (TPE) | – | – |
| Colour | Black, non-marking | – | – |
| Hardness | 60 (product listing) / 70 (datasheet) | Shore A | Manufacturer listing and datasheet (method not stated) |
| Tensile strength | 7 | MPa | Manufacturer datasheet |
| Elongation at break | 340 | % | Manufacturer datasheet |
| Density | 1.09 | g/cm³ | Manufacturer datasheet |
| Working temperature | −40 to +90 (listing) / −35 to +90 (datasheet) | °C | Manufacturer data |
| Dimensional tolerance | Class E2 (cross-section), L2 (cut length) | – | ISO 3302-1 |
| Tear strength | Not published for this profile | – | – |
| Compression set | Not published for this profile | – | – |
Where the manufacturer's product listing and datasheet differ (hardness, lower temperature limit) both figures are shown. Design to the more cautious value.
Materials and compliance
Made from a black thermoplastic elastomer: a rubber-like material that is waterproof, lightweight and non-marking, so it will not leave black streaks on painted steel, glass or light-coloured surfaces. No food-contact, potable-water or other regulatory approvals are stated for this black grade, so do not use it where certified food-contact material is required. A white food-contact grade of the same 20 x 8 mm size is available separately.
Typical uses
- Hatch and access-panel seals on machinery and equipment
- Enclosure door and lid seals where only light closing pressure is available
- Glass and sheet panel edge seals, and architectural/window seals
- Draught, dust and splash seals on cabinet and cupboard doors
- Sealing the gap between adjacent panels on fabricated steelwork
Fitting

- Fix the flat flange to the fixed frame so the bead meets a clean closing face on the door or lid.
- Clean and degrease the fixing surface; bond the flange with a contact adhesive suitable for TPE, or hold it under a clamping strip, rivets or screws through the outer part of the flange.
- Lay the profile in without stretching it; stretched seal shrinks back and opens gaps at the corners.
- Aim for the bead to be squeezed by roughly a quarter to a third when closed – a closed gap of about 5–6 mm.
- At corners, notch the flange so the bead can run round continuously, or mitre and bond the joint.
How much do I need?
Measure the full perimeter of each opening and add about 5% for trimming and corners. Example: four enclosure doors of 600 x 800 mm need 4 x 2.8 m = 11.2 m, plus 5% = about 11.8 m, so one 25 m coil covers them with spare.
Questions
Is the 8 mm bead hollow or solid?
Hollow. It has a 6 mm bore and a 1 mm wall, which is why it compresses with light pressure and suits doors and hatches that cannot be forced shut.
What gap does it seal?
As a guide, a closed gap of about 5–6 mm, so the 8 mm bead is squeezed by a quarter to a third. For gaps of 7 mm or more choose a larger bead, such as our 28 x 10.5 mm P profile.
How do I fix the flange?
Bond it with a contact adhesive suitable for thermoplastic elastomers, or mechanically fix it under a clamping strip, rivets or screws. Always clean and degrease the surface first.
What temperatures can it take?
The working range is −40 °C to +90 °C (the manufacturer datasheet quotes −35 °C as the lower limit). It is not suitable for oven doors or other hot surfaces above 90 °C; use a silicone P profile there.
Can I cut and join it?
Yes. Cut it square with a sharp knife or snips. Butt joints can be bonded with a cyanoacrylate adhesive suitable for TPE; for a continuous seal round a frame, notch the flange at the corners so the bead runs unbroken.
Will it mark painted surfaces or glass?
No. The compound is non-marking, so it will not leave black streaks on paint, powder coat or glass.
Can I use it outdoors?
Yes. The material is waterproof and suits outdoor hatches and enclosures within its temperature range.
Is this grade food safe?
No food-contact approval is stated for this black grade. Choose the white food-contact grade 20 x 8 mm P profile if you need certified food-contact material.
Can I buy a shorter length?
This listing is the 25 m coil. Contact us for cut lengths or larger quantities.
Need help choosing the right seal? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEP-20X8-STD |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black TPE P Profile Seal – 20mm Flange x 8mm Hollow Bead – 25m Coil