
Rubber & FoamSKU IP-RBG-86X60-1M
EPDM Rubber Brick Grab – 86mm x 60mm Profile – 1m or 1.25m Length
Price shown updates with the option you pick.
This EPDM rubber brick grab 86mm x 60mm is a heavy-duty replacement jaw insert for hydraulic brick grabs, designed to fit the Kinshofer KM 331. It gives a firm, high-friction hold on bricks, blocks and paving while cushioning the load against chipping and face-marking. Supplied as a single 1m or 1.25m length.
At a glance
- 86mm wide x 60mm high solid rubber profile
- Replacement grab rubber for Kinshofer KM 331 jaws
- 80° Shore A EPDM: firm enough to clamp, resilient enough to protect the load
- High-friction face reduces slipping on wet or dusty packs
- Resists UV, ozone, frost and weathering for outdoor yard use
- Sold as a 1m or 1.25m length, easy to trim with a rubber knife
Typical uses
- Re-padding hydraulic brick stack grabs and mechanical grapples
- Lorry-mounted crane and loader crane attachments in builders' merchants
- Handling palletised and loose bricks, concrete blocks and paving slabs
- Brickworks, masonry yards and construction site material handling
- A spare grab pad to keep a worn set from damaging stock
Which one do I need?
| Length | Best for |
|---|---|
| 1m | Standard jaw faces up to one metre, or as a spare pad for one jaw |
| 1.25m | Wider jaws, or where you want enough material to trim a full-length pad in one piece |
Technical drawing
Specification
| Material | EPDM rubber |
| Profile size | 86mm wide x 60mm high |
| Hardness | 80° Shore A |
| Colour | Black |
| Lengths | 1m or 1.25m |
| Compatible with | Kinshofer KM 331 brick grab |
How much do I need?
Measure the face of each grab jaw. A grab with two 950mm jaws needs two 1m lengths, each trimmed to 950mm. For two 1.2m jaws, order two 1.25m lengths and trim the spare 50mm from each. Most yards keep one extra length in stock so a damaged pad can be swapped straight away.
Fitting tips
- Remove the worn pad and clean mortar, grit and debris out of the jaw retaining channel.
- Slide or press the new profile along the full length of the jaw so it sits evenly.
- Trim to length with a sharp rubber knife, keeping the cut square.
- Secure the insert as the grab manufacturer's instructions require, then test under a safe load before full use.
Complete your project
- Nitrile Solid Rubber Seal – 55mm x 55mm – 5m Roll
- Solid Nitrile Rubber Square Seal – 50mm x 50mm – Per Metre
- Nitrile Solid Rubber Seal – 30mm x 55mm – 5m Roll
Questions
Will this rubber brick grab fit my grab?
It is made to fit the Kinshofer KM 331 brick grab. For other grabs, check that your jaw channel takes an 86mm x 60mm profile before ordering.
Can the grab pad be left outdoors?
Yes. EPDM resists UV, ozone, frost and rain, so it suits yards and lorry cranes that work outside all year.
How does the rubber protect bricks and blocks?
The 80° Shore A rubber spreads the clamping force across the pack, which reduces point pressure, chipping and marking on facing bricks.
Can I cut it to suit my jaw width?
Yes. Cut it with a sharp rubber knife or fine saw and keep the cut square so the pad sits flat.
When should I replace a brick grab rubber?
Replace it when the face is worn smooth, torn or compressed, or when packs start to slip in the grab.
Not sure which size you need? Contact our team and we will help.
Product details
| SKU | IP-RBG-86X60-1M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Rubber Brick Grab – 86mm x 60mm Profile – 1m or 1.25m Length