
Rubber & FoamSKU IP-NBRS-55X55-STD
Nitrile Solid Rubber Seal – 55mm x 55mm NBR Profile – 5m Roll
This nitrile solid rubber seal 55mm x 55mm is a heavy, fully solid square section of black NBR for hatches, doors and impact points where oil or fuel contact is expected. It is sold as one 5m strip that you cut to length on site.
At a glance
- Solid square section, 55mm x 55mm, with no hollow or sponge core
- Nitrile (NBR / Buna-N) rubber with excellent resistance to oil, grease and aliphatic hydrocarbons
- 70 Shore A hardness for strength and impact resistance
- Seals against air and water when compressed in a hatch or door
- Doubles as a heavy-duty rubber buffer or anti-vibration strip
- Supplied as a single 5m length in black
Typical uses
- Oil-resistant hatch seal for marine, vehicle and industrial hatches
- Heavy-duty door seal where fuel or lubricant splash is likely
- Impact buffer strip on machinery, loading points and guards
- Anti-vibration packing under heavy equipment
- Square rubber gasket section for oily plant rooms
Which one do I need?
| Seal | Best for |
|---|---|
| NBR solid square 55 x 55mm (this product) | Large gaps with high closing force and oil or fuel contact; impact and buffer duty |
| Hatch seal 40 x 20mm | Lighter hatches that need an easily compressed sponge-backed seal |
| Hatch seal 70 x 32mm | Wide hatch channels where a composite solid and sponge seal is preferred |
Technical drawing
Specification
| Material | Nitrile rubber (NBR, Buna-N) |
| Construction | Solid rubber, no sponge core |
| Cross-section | 55mm x 55mm square |
| Hardness | 70 Shore A |
| Colour | Black |
| Unit of sale | One 5m strip |
| Key resistance | Oil, grease and aliphatic hydrocarbons |
How much do I need?
Measure the full run of the hatch or door perimeter and add about 50mm for each joint. Example: a 1000mm x 800mm hatch has a perimeter of 3.6m, so one 5m strip covers it with 1.4m spare for a second small opening or for buffers.
For buffer duty, add up the length of every strike point; short 150mm to 300mm pads are typical.
Fitting tips
- Cut with a sharp long blade lubricated with soapy water for a straight, square end.
- Clean and degrease steel surfaces before bonding with a nitrile-compatible contact adhesive.
- Solid rubber needs much more closing force than sponge, so check that hinges and clamps can compress it.
- Butt joints square and bond them, keeping the joint away from the corner most loaded by the hatch clamp.
- Let the strip relax flat for a few hours before fitting to remove any set from coiling.
Complete your project
- Watertight Hatch Seal – 40mm x 20mm
- Watertight Hatch Seal – 38mm x 30mm
- Watertight Hatch Seal – 70mm x 32mm
Questions
Is this seal suitable for contact with oil and fuel?
Yes. Nitrile is chosen for oily conditions because it resists oil, grease and aliphatic hydrocarbons far better than natural rubber or EPDM.
How does a solid seal compare with a sponge hatch seal?
A solid seal does not compress as easily, so it needs a stronger closing force, but it is tougher and much more resistant to impact and abrasion.
Can it be used as a rubber buffer?
Yes. The 55mm square solid section works well as an impact strip or anti-vibration packing as well as a seal.
Is it hollow?
No. The whole 55mm x 55mm section is solid rubber, as shown in the technical drawing.
How is it supplied?
As one 5m strip in black, which you cut to the lengths you need.
Need help choosing? Contact our team for practical advice on sizes, materials and fitting.
Product details
| SKU | IP-NBRS-55X55-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Nitrile Solid Rubber Seal – 55mm x 55mm NBR Profile – 5m Roll