
Rubber & FoamSKU IP-RRE-40X7-10M
EPDM Rubber Ramp Edge – 40mm x 7mm – 10m Roll
This EPDM rubber ramp edge 40mm x 7mm is a tapered black rubber edging strip that finishes the exposed edge of floor matting up to 6mm thick, giving a smooth slope from floor to mat instead of a trip lip. It is sold as one continuous 10m roll that you cut to length on site.
At a glance
- 40mm wide ramp profile, 7mm high at the thick side
- Suits rubber and PVC matting up to 6mm thick
- Tapers to a fine edge so trolleys and wheelchairs roll on easily
- EPDM rubber, 70° Shore A, resists UV, ozone and weather
- Light at about 0.18kg per metre, easy to handle and cut
- Black, supplied as a single 10m roll
Typical uses
- Finishing electrical safety and switchboard matting in front of panels
- Edging fine ribbed and heavy-duty ribbed rubber matting runs
- Making anti-slip PVC matting edges trip-safe in walkways
- Creating accessible mat transitions in shops, offices and public areas
- Outdoor and wet-area mat edges where weather resistance matters
Which one do I need?
| Your matting | Edging to choose |
|---|---|
| Rubber or PVC mat up to 6mm thick | This EPDM ramp edge 40mm x 7mm |
| 10mm low-profile PVC mats | PVC mat edging strip 10mm |
| Thicker than 7mm | Not this profile: the mat would stand proud of the ramp |
Technical drawing
Specification
| Product | Rubber ramp edge (mat edging strip) |
| Material | EPDM rubber |
| Width | 40mm |
| Height (thick side) | 7mm |
| Suits mat thickness | Up to 6mm |
| Hardness | 70° Shore A |
| Weight | 0.18kg per metre |
| Colour | Black |
| Unit of sale | 10m roll |
How much do I need?
Measure every mat edge that people or trolleys will cross. Example: a 1m x 10m run of switchboard matting with only one long side open to the walkway needs 10m, so one roll. If all four sides are open you need 22m, so three rolls (two rolls would leave you 2m short). Allow a little extra for squaring off the ends and mitring corners.
Fitting tips
- Let the roll lie flat at room temperature for a few hours so it loses its coil set.
- Butt the thick side tight to the mat edge with no gap, feather edge to the floor.
- Cut with a sharp utility knife against a straight edge for clean, square ends.
- Mitre corners at 45 degrees around rectangular mats for a neat, continuous edge.
- In busy walkways, bond it to a clean, dry floor with contact adhesive or heavy-duty double-sided tape.
Complete your project
- Electrical Insulating Fine Ribbed Rubber Mat 6mm Thick
- Switchboard Matting 5mm – Electrical Insulation Mat
- PVC Mat Edging Strip – 10mm Low Profile – 10.1m Roll
Questions
What thickness of mat does this ramp edge suit?
Matting up to 6mm thick. The edge stands 7mm at its thick side, so a 3mm to 6mm mat finishes flush or just below it.
Can this rubber mat edging be used outdoors?
Yes. EPDM resists UV light, ozone and weathering, so it suits outdoor ramps and wet areas as well as indoor walkways.
Is it sold per metre or by the roll?
By the roll. The price is for one continuous 10m length, which you cut to size.
Do I have to glue the edging down?
Not always. It can be loose-laid in light-traffic areas; for trolley routes and busy corridors bond it with contact adhesive or heavy-duty tape.
Will wheelchairs and trolleys roll over it?
Yes. The tapered 40mm slope lets wheels ride up onto the mat instead of catching on a raised edge.
Need help choosing edging for your matting? Contact our team with your mat thickness and layout.
Product details
| SKU | IP-RRE-40X7-10M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Rubber Ramp Edge – 40mm x 7mm – 10m Roll