
Rubber & FoamSKU IP-UCH-6X8.5-15
EPDM U Channel 6mm x 8.5mm – Fits 2mm Panels – Black Rubber Edge Trim – 15m to 30m
Price shown updates with the option you pick.
A push-on edge trim for 2 mm sheet. This solid black EPDM U channel is 6 mm wide and 8.5 mm high, with a 2 mm channel about 6.5 mm deep. Its teardrop section is slim at the mouth and thickens towards a fully rounded crown, so the finished edge is soft, full and hard-wearing. Press it onto cut edges of steel, aluminium, acrylic, polycarbonate, composite panel, plywood or glass to cover sharp edges and take knocks. Choose one continuous length from 15 m to a full 30 m coil; every length is held in stock in the UK.
At a glance
- Fits 2 mm panels: 2 mm wide channel, about 6.5 mm deep, so it covers the edge and a good band of each face.
- 6 × 8.5 mm teardrop profile: rounded crown about 2 mm thick over the panel edge.
- Solid EPDM, 65–75 Shore A: tensile strength 10 MPa, elongation at break 500%, tear strength 50 kN/m.
- Made for outdoor use: no cracks after the 72 h ozone test, with good resistance to weathering, flexing and abrasion.
- No tools needed: push on by hand and cut with a sharp knife. Bond with PU or silicone sealant for a permanent or sealed fit.
- Any length from 15 m to 30 m: one continuous piece. The 30 m full coil has the lowest price per metre.
Technical drawing

Nominal dimensions in mm, free (unfitted) state. Width, height and channel width are the manufacturer's figures. Channel depth and base thickness (marked ≈) are scaled from the manufacturer's drawing and are not separately toleranced.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | Teardrop (round-base) U channel edge trim | Manufacturer's drawing |
| Overall width | 6 mm | Manufacturer's drawing, nominal |
| Overall height | 8.5 mm | Manufacturer's drawing, nominal |
| Channel width | 2 mm | Manufacturer's drawing and technical data, nominal |
| Channel depth | about 6.5 mm | Scaled from manufacturer's drawing |
| Base (crown) thickness | about 2 mm | Scaled from manufacturer's drawing (8.5 − 6.5) |
| Fits panel thickness | 2 mm | Manufacturer's data sheet |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer's data sheet |
| Colour | Black | – |
| Hardness | 65–75 IRHD (±5), stated as 65–75 Shore A | IRHD, manufacturer's data sheet |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500% | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21% | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C |
| Heat ageing: change in elongation at break | 0% | 70 h at 70 °C |
| Weight | 0.05 kg per metre (30 m coil about 1.5 kg) | Manufacturer's data |
| Lengths available | 15, 16, 17 … 29 m, or a full 30 m coil (one continuous piece) | – |
| Service temperature | about −40 °C to +120 °C, typical for EPDM, not tested on this profile | General EPDM data |
| Density | Not stated for this profile | – |
| Dimensional tolerance | Not stated; extruded rubber is normally made to ISO 3302-1 tolerance classes | – |
Materials and compliance
This profile is extruded from a solid EPDM compound. EPDM resists weathering, ozone, UV and water, and keeps its flexibility over time. The test results in the table come from the manufacturer's data sheet for this profile.
The manufacturer does not state any food-contact, WRAS, REACH, RoHS or fire approval for this product, so we do not claim one. If your application needs a certified material, please contact us before ordering.
How it fits

Choosing your length
Add up the total length of edge to be covered and allow about 5% extra for cutting and joints. For example, a 2,440 × 1,220 mm sheet edged on all four sides needs about 7.3 m, so two sheets fit in a 15 m length. The price covers one continuous piece of the length you choose.
| Length | Price inc VAT | Price per metre |
|---|---|---|
| 15 m | £199.74 | £13.32 |
| 18 m | £239.67 | £13.32 |
| 20 m | £266.31 | £13.32 |
| 22 m | £292.95 | £13.32 |
| 25 m | £332.88 | £13.32 |
| 29 m | £386.16 | £13.32 |
| 30 m full coil | £343.80 | £11.46 |
Need 26 m or more? The full 30 m coil costs less than any length from 26 m to 29 m.
Typical uses
- Edges of 2 mm steel, aluminium and composite panels on guards, enclosures and machine covers
- 2 mm acrylic and polycarbonate screens, displays and protective shields
- Vending machines, shop fittings, furniture and cabinet panels
- Doors, hatches and access panels that need a soft, safe edge
- Stair and step nosings, running boards and trailer panels with 2 mm edges
- Bonded into aluminium window channels as a push-in seal
Fitting
- Deburr and clean the edge. Check the sheet is 2 mm thick.
- Start at a corner and press the channel on with your thumb. Work along the edge.
- On outside corners, ease the trim round the bend. On tight corners, cut a small V-notch out of the legs.
- Cut a few millimetres long with a sharp knife, then push the ends together into a tight butt joint.
- For a sealed or permanent fit, run a bead of PU or silicone sealant into the channel first.
FAQ
What panel thickness does it fit?
Panels 2 mm thick. On thinner sheet (1.5 mm) it will sit looser; bond it with sealant, or bond a thin strip inside the channel to take up the gap. For 3 mm panels choose the 5.5 × 8.5 mm U channel for 3 mm sheet.
How do I measure what I need?
Measure the panel thickness with a caliper first, then measure the total edge length in metres and round up. Allow about 5% extra for cuts and joints.
Can it be used outdoors?
Yes. EPDM is chosen for outdoor use because it resists weathering and ozone. This compound passed a 72 h ozone test with no cracks.
What temperatures can it take?
The manufacturer has not published a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, but this has not been tested on this profile. The compound did pass heat ageing for 70 h at 70 °C with little change in properties.
How do I cut and join it?
Use a sharp knife or heavy shears and cut square. Butt the ends together tightly. For a sealed joint, add a little cyanoacrylate glue or sealant to the cut faces.
Is it soft or firm?
At 65–75 Shore A it is medium-firm: soft enough to absorb knocks, and firm enough to hold its shape and grip the panel.
Why is the 30 m length cheaper than 29 m?
30 m is a full, uncut coil, so there is no cutting or handling, and it is priced lower. If you need 26 m or more, the coil is the cheaper buy.
Why is the shortest length 15 m?
This profile comes on 30 m coils and the minimum cut length is 15 m. Every length is one continuous piece with no joins.
Is it food-safe or certified?
The manufacturer states no food-contact or other approvals for this product, so we do not claim any. Ask us about certified alternatives.
Is it in stock?
Yes. All lengths are held in stock and dispatched from the UK.
Related profiles
- EPDM U Channel 5.5 × 8.5 mm, for 3 mm panels
- EPDM U Channel 5.7 × 17 mm deep grip, for 1.5–2.5 mm panels
- EPDM Square U Channel 5 × 8.5 mm, for 1.6 mm panels
- EPDM U Channel 4.5 × 9 mm, for 1.6 mm panels
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-UCH-6X8.5-15 |
|---|---|
| Weight | 1.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM U Channel 6mm x 8.5mm – Fits 2mm Panels – Black Rubber Edge Trim – 15m to 30m