
Rubber & FoamSKU IP-SGDS-17X10-10M
EPDM Self-Grip Door Seal 17mm x 10mm – Sponge Bulb, Fits 1.6–3mm Panels – 10m to 50m
Price shown updates with the option you pick.
A push-on door seal for 1.6mm to 3mm panel and frame edges. The solid EPDM clip, reinforced with a steel wire carrier and lined with a gripping lip and fins, holds itself on the edge with no glue or fixings. On its side sits a hollow sponge EPDM bulb, 8mm wide and 10mm tall, that gives a soft, weather-tight seal against a closing door, lid or hatch. Overall size 17mm wide x 10mm high. Choose any length from 10m up to a full 50m coil; it comes as one continuous length.
At a glance
- 17mm x 10mm profile: 10.5mm tall clip plus an 8mm x 10mm hollow sponge bulb
- Fits panel edges 1.6mm to 3mm thick (5mm inside width of clip)
- Solid EPDM clip with gripping lip, three fins and steel wire carrier: no adhesive needed
- Works from -40°C to +80°C; EPDM resists weather, ozone and water
- One continuous length, 10m to 49m, or a 50m full coil at the lower coil rate
Typical uses
- Electrical enclosure, control cabinet and kiosk doors
- Access hatches, inspection panels and machine guards
- Garage, shed and outbuilding doors
- Bus, train, trailer and vehicle body doors and interior side panels
- Side windows, marine hatches and locker lids
Technical drawing


Specifications
| Property | Value | Test method / note |
|---|---|---|
| Dimensions | ||
| Overall width | 17mm | Nominal |
| Overall height | 10mm (clip 10.5mm) | Nominal |
| Clip height | 10.5mm | Nominal |
| Inside width of clip | 5mm | Nominal, before fitting |
| Sponge bulb width | 8mm | Nominal |
| Sponge bulb height | 10mm | Nominal |
| Fits panel / edge thickness | 1.6mm to 3mm | - |
| Dimensional tolerance | Not stated by the manufacturer | Ask us if critical |
| Colour | Black | - |
| Lengths | 10m to 49m in 1m steps; 50m full coil | One continuous length |
| Construction | ||
| Clip, lip and fins | Solid EPDM | - |
| Sealing bulb | Hollow sponge (cellular) EPDM | - |
| Carrier | Steel wire, type Fe 50 | UNI 5961-67 |
| Solid EPDM clip | ||
| Hardness | 80 ± 5 Shore A | ASTM D2240 (product page quotes 67° to 82°) |
| Tensile strength | 80 kg/cm² min (about 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm min (about 29 kN/m) | ASTM D624 |
| Elongation at break | Not stated by the manufacturer | - |
| Brittle point | -40°C | ASTM D746 |
| Compression set | 40% max | ASTM D395 Method B |
| Air ageing, 70 h at 70°C: hardness change | +2 points | - |
| Air ageing, 70 h at 70°C: tensile change | +15% | - |
| Ozone resistance (70 h, 50°C, 50 pphm, 20% strain) | No cracks | ASTM D1149 |
| Sponge EPDM bulb | ||
| Density (indicative) | 550 to 600 kg/m³ | Data sheet prints the unit as g/cm³ |
| Brittle point | -40°C | ASTM D746 |
| Ozone resistance (70 h, 50°C, 50 pphm, 50% strain) | No cracks | ASTM D1149 |
| Water absorption (22 h at 23°C) | 1.2% max | ASTM D1056 |
| Tensile strength | 7 to 10 kg/cm² (about 0.7 to 1.0 MPa) | ASTM D412 |
| Tear resistance | 0.6 / 0.8 kg/mm | ASTM D624 |
| Steel carrier | ||
| Hardness | 80 to 90 HRB (Rockwell B) | - |
| Tensile strength | 50 kg/mm² min (about 490 MPa) | - |
| Complete profile | ||
| Operating temperature | -40°C to +80°C | - |
| Compression set (7 days at 70°C) | 50% max | ASTM D1056 |
| Migration stain on organic finishes | Satisfactory | ASTM D925 |
| Contact stain on organic finishes | Satisfactory | ASTM D925 |
| Colour fastness | Satisfactory | ASTM D750 |
| Bulb compression in use | 30% to 40% ideal; 40% max on product data, never above 50% | Manufacturer guidance |
All values are from the manufacturer's data for this profile. kg-based units are converted to SI for convenience and rounded.
Materials and compliance
The clip is solid EPDM over a steel wire carrier and the bulb is closed-cell sponge EPDM. EPDM is the usual choice for outdoor sealing because it resists rain, UV and ozone, and the stain tests above mean it will not mark painted or powder-coated finishes. The manufacturer does not state any food-contact, drinking-water, fire or REACH/RoHS approvals for this profile, so we do not claim any. If you need a certificate or declaration for your application, ask us before ordering.
How much do I need?
Measure every edge the seal will run along, add them together and pick the next length up. A cabinet door of 1.5m x 1m has a perimeter of 5m, so two such doors need 10m. Allow about 0.5m extra per opening for trimming at the joint. Each length is priced at £15.27 per metre inc VAT; the 50m full coil works out at £11.46 per metre, so from 38m upwards the full coil is the cheaper buy.
Fitting
- Clean the edge and file off any burrs.
- Decide which side the door closes against: the bulb sits on that side of the panel.
- Start at the hinge side or the bottom so the joint is where water will not collect.
- Push the clip on by hand, then tap along it with a rubber or plastic mallet until the edge is fully home inside the clip.
- Ease the seal round radiused corners; for a sharp 90° corner, notch the clip on the inside of the bend or cut and butt-join.
- Set the closed door gap so the 8mm bulb squashes by about 2.4mm to 3.2mm (30% to 40%).
Frequently asked questions
Does it need glue or screws?
No. The gripping lip, fins and steel wire carrier clamp the seal onto a 1.6mm to 3mm edge by themselves.
Will it fit a 1mm or a 4mm panel?
No. It is made for 1.6mm to 3mm edges. Thinner panels will not be gripped firmly and thicker ones will not seat fully in the clip. For 1mm to 2mm edges see the 12.5mm x 8mm seal below, or ask us for another grip range.
Which side does the bulb go?
The bulb sits on one side of the panel, so fit it on the face the door or lid closes against. Check this before you start, as the seal cannot be reversed once fitted.
How do I cut and join it?
Cut with heavy-duty scissors or side snips, going cleanly through the wire carrier. Butt the two ends tightly at the joint; a drop of rubber-compatible cyanoacrylate on the sponge faces gives a neater, sealed join if you want one.
Will it go round corners?
Yes. It follows radiused corners easily. On tight corners, a small V-notch in the clip on the inside of the bend stops it bunching.
Can it be used outdoors and in the cold?
Yes. It is rated from -40°C to +80°C and EPDM resists weather, ozone and water, so it suits garden buildings, vehicles, boats and outdoor enclosures. It is not intended for hot areas above 80°C such as ovens or exhausts.
What happens if the gap is too tight?
Squashing the bulb more than 50% can leave it permanently flattened, so it stops sealing. Aim for 30% to 40% compression; if the gap is bigger than the bulb can fill, choose a larger profile.
How big is it in the hand?
The whole section is 17mm across, a little narrower than a 1p coin and about the width of a fingertip. The size-comparison illustration in the gallery is drawn to scale.
Is it in stock?
Yes. All lengths are cut from stock and dispatched as shown at checkout.
Which size do I need?
| Profile | Best for |
|---|---|
| 17mm x 10mm (this seal) | 1.6mm to 3mm panels with a medium gap |
| 12.5mm x 8mm | Thinner 1mm to 2mm panels with a small gap: the slimmest option |
| 17.7mm x 13.5mm | A taller profile for deeper gaps: check the panel range on its page |
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SGDS-17X10-10M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Self-Grip Door Seal 17mm x 10mm – Sponge Bulb, Fits 1.6–3mm Panels – 10m to 50m