
Rubber & FoamSKU IP-IPSGD-12.5X8-STD
EPDM Self-Grip Door Seal – 12.5mm x 8mm – Per Metre
This EPDM self-grip door seal 12.5mm x 8mm pushes onto panel edges 1mm to 2mm thick, sealing enclosure doors, cabinets, hatches and machine guards while covering sharp sheet metal edges. It is sold per metre: enter the number of metres you need as the quantity.
At a glance
- Compact 12.5mm x 8mm self-grip edge seal with sponge bulb
- Grips sheet and panel edges 1mm to 2mm thick
- Solid EPDM clip with embedded steel wire carrier - no adhesive
- Sponge EPDM bulb closes small door and hatch gaps
- Works from -40°C to +80°C, weather and UV resistant
- Sold per metre, cut from a 50m coil
Typical uses
- Sealing electrical enclosure and control cabinet doors
- Draught and dust sealing on access hatches and machine guards
- Rubber edge trim for raw sheet metal on vehicle and trailer bodies
- Marine lockers and outdoor equipment housings
- Finishing thin panels where a slim door seal is needed
Which one do I need?
| Profile | Best for |
| 12.5mm x 8mm (this seal) | Thin 1mm to 2mm panels with a small closed gap - the slimmest option |
| 15.5mm x 10mm | Same 1mm to 2mm panels where a slightly larger gap needs a bigger bulb |
| 13.4mm x 11mm or 13.5mm x 12.5mm | Taller profiles for deeper gaps - check the panel range on each page |
Aim for the bulb to compress by 30% to 40% when the door is shut. If the gap is larger than the bulb can fill, step up a size.
Technical drawing
Specification
| Profile size | 12.5mm wide x 8mm high |
| Panel thickness range | 1mm to 2mm |
| Material | Solid EPDM clip, sponge EPDM bulb, steel wire carrier |
| Colour | Black |
| Hardness | 67° to 82° Shore A (solid section) |
| Temperature range | -40°C to +80°C |
| Maximum compression | 40% (30% to 40% recommended) |
| Unit of sale | Per metre (quantity = metres) |
How much do I need?
Measure every edge the seal will run along and round up to the next whole metre. A cabinet door of 1.5m x 1m has a perimeter of 1.5 + 1 + 1.5 + 1 = 5m, so order a quantity of 5; two such doors need 10. Add half a metre per opening if you want spare for trimming at the joint.
Fitting tips
- Clean the panel edge and remove burrs before fitting.
- Start at the bottom or hinge side so the joint sits where water does not collect.
- Press the clip on by hand, then tap along it with a rubber mallet to seat it fully - no glue is needed.
- Cut with heavy-duty snips, cleanly through the wire carrier, and butt the ends tightly.
- Keep bulb compression below 50% or the sponge can take a permanent set.
Complete your project
- EPDM Self-Grip Door Seal – 15.5mm x 10mm for 1mm to 2mm Panels
- EPDM Self-Grip Door Seal – 13.5mm x 12.5mm – Per Metre
- EPDM Self-Grip Top Seal – 44.5mm High, Fits 1.6mm-3mm Panels
Questions
Will this self-grip door seal go round corners?
Yes. The flexible EPDM and wire carrier follow radiused corners; for a tight 90° corner, cut and butt-join for the neatest seal.
Do I need glue to fit it?
No. The steel wire carrier clamps the clip onto 1mm to 2mm panels on its own.
Will it fit a 3mm panel?
No - this profile is made for 1mm to 2mm edges. For thicker panels choose a seal with a wider grip range.
Can it be used outdoors?
Yes. EPDM resists weather, UV and moisture and works from -40°C to +80°C.
What happens if I compress it too much?
Above 50% compression the sponge bulb can deform permanently and stop sealing, so set the closed gap for 30% to 40%.
Need help choosing the right edge seal? Contact our team for advice.
Product details
| SKU | IP-IPSGD-12.5X8-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Self-Grip Door Seal – 12.5mm x 8mm – Per Metre