
Rubber & FoamSKU IP-IPSGT-22.5-11
Self-Grip EPDM Top Seal – 22.5mm High – Offset Sponge Bulb, Fits 1-2mm Panels – 11m to 25m
Price shown updates with the option you pick.
A push-on EPDM top seal for 1mm to 2mm sheet and panel edges. A metal-reinforced solid EPDM grip clamps the edge with no glue, and a hollow sponge EPDM bulb, raised 10.5mm above the grip on an angled stem, seals against a closing hatch, lid, door or roof panel. It stands 22.5mm high overall, is black, and comes as one continuous length from 11m to 24m, or a full 25m coil. Cut lengths work out at £20.70 per metre inc VAT; the 25m coil is £15.84 per metre.
At a glance
- 22.5mm overall height; the sponge bulb sits 10.5mm above the top of the grip
- Grip channel 4mm opening x 9.5mm deep; fits edges 1mm to 2mm thick
- Solid EPDM grip (80 ± 5° Shore A) with a full-length U-shaped steel carrier and internal gripping fingers
- Offset hollow sponge bulb with a small fin, for a soft, low-force seal
- Weather and ozone resistant EPDM, -40°C to +80°C
- In stock in the UK; each length is one piece with no joins
Technical drawing

Specification
| Property | Value | Test method / note |
|---|---|---|
| Overall height | 22.5mm | Base of grip to tip of the bulb fin |
| Bulb height above grip | 10.5mm | Top of grip to tip of the bulb fin |
| Grip height | 12mm | Derived: 22.5mm minus 10.5mm |
| Grip channel opening | 4mm | Nominal, before fitting |
| Grip channel depth | 9.5mm | Nominal; the edge should be at least this deep to seat fully |
| Fits panel / edge thickness | 1mm to 2mm | Manufacturer fitting range |
| Sponge bulb size | Approx. 7mm across | Scaled from the manufacturer's drawing; not a stated dimension |
| Overall width | Not stated by the manufacturer | Approx. 11 to 12mm, scaled from the drawing |
| Grip material | Solid EPDM rubber | - |
| Bulb material | Sponge (cellular) EPDM | - |
| Carrier | Steel, U-shaped, full length | Type Fe 50 to UNI 5961-67 |
| Colour | Black | - |
| Solid EPDM grip | ||
| Hardness | 80° ± 5° Shore A (listed range 67° to 82°) | ASTM D2240 |
| Tensile strength | 80 kg/cm² min (approx. 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm min (approx. 29 kN/m) | ASTM D624 |
| Brittle point | -40°C | ASTM D746 |
| Compression set | 40% max | ASTM D395 Method B |
| Hardness change after air ageing | +2° Shore A | 70h at 70°C |
| Tensile change after air ageing | +15% | 70h at 70°C |
| Ozone resistance | No cracks | ASTM D1149, 70h at 50°C, 50 pphm, 20% elongation |
| Sponge EPDM bulb | ||
| Density (indicative) | 550 to 600 kg/m³ (0.55 to 0.60 g/cm³) | Manufacturer figure |
| Tensile strength | 7 to 10 kg/cm² (approx. 0.7 to 1.0 MPa) | ASTM D412 |
| Tear resistance | 0.6 to 0.8 kg/mm | ASTM D624 |
| Water absorption | 1.2% max | ASTM D1056, 22h at 23°C |
| Brittle point | -40°C | ASTM D746 |
| Ozone resistance | No cracks | ASTM D1149, 70h at 50°C, 50 pphm, 50% elongation |
| Steel carrier | ||
| Hardness | 80 to 90 HRB | Rockwell B |
| Tensile strength | 50 kg/mm² min (approx. 490 MPa) | - |
| Complete profile | ||
| Operating temperature | -40°C to +80°C | Continuous service |
| Compression set (bulb) | 50% max | ASTM D1056, 7 days at 70°C |
| Recommended bulb compression | 30% to 40%; 40% max in service (the data sheet's absolute limit is 50%) | Manufacturer guidance |
| Staining (migration and contact) | Satisfactory | ASTM D925 |
| Colour fastness | Satisfactory | ASTM D750 |
| Elongation at break | Not stated by the manufacturer | - |
| Dimensional tolerance | Not stated by the manufacturer; extruded sponge sections are typically held to ISO 3302-1 class E2 (typical for EPDM extrusions, not tested on this profile) | - |
| Supplied as | One continuous length, 11m to 24m in 1m steps, or a full 25m coil | - |
Materials and compliance
The grip and stem are solid EPDM, the sealing bulb is closed-skin sponge EPDM, and the core is a U-shaped steel carrier. EPDM is chosen here for its resistance to weather, UV, ozone and water. The manufacturer does not state any food-contact, drinking-water, REACH or RoHS approval for this profile, so we do not claim one. If you need a certificate for your application, ask us before ordering.
How it fits

Typical uses
- Sealing the closing edge of access hatches, inspection covers and lids made from thin sheet
- Weatherproofing electrical enclosure, cabinet and kiosk doors
- Vehicle, bus, train and van body doors, side windows and interior panels
- Marine lockers and equipment hatches
- Roof panels, glazing panels and machine guards
- Covering raw sheet-metal edges while sealing at the same time
Which one do I need?
| Top seal | Choose it when |
|---|---|
| 22.5mm high (this seal) | 1mm to 2mm edges and a compact bulb offset to one side of the grip |
| 20mm x 32mm | The same 1mm to 2mm edges with a much larger bulb for bigger gaps |
| 11mm x 16mm | Thinner 0.8mm to 1.2mm sheet and a lower profile |
| 12mm x 21mm | Thicker 1.6mm to 3mm edges at a similar height |
How much do I need?
Add up every edge the seal runs along, then add about 5% for trimming. A hatch of 1.5m x 1m has a perimeter of 5m, so two hatches need about 10.5m and the 11m length covers them. The 25m full coil (£396.00) costs less than any cut length from 20m upwards, so choose it whenever you need more than 19m.
Fitting
- Clean the edge and file off burrs; the edge must be 1mm to 2mm thick and ideally at least 9.5mm deep.
- Start at the centre of the bottom or least visible edge, with the bulb facing the closing surface.
- Press the grip on by hand, then tap along it with a rubber or plastic mallet until the edge is fully seated in the channel.
- Go round radiused corners in one piece. At sharp corners, cut a small notch out of the grip only so the bulb stays continuous.
- Cut the end square with heavy-duty side cutters (through the steel), leave it 2mm to 3mm long and push it in tight against the start for a closed joint.
- Check the closed gap: the sponge bulb should be squashed by 30% to 40% and never more.
Data sheet
Download the technical data sheet (PDF)
Questions
Is it sold per metre?
No. Each option is one continuous length (11m to 24m) or a full 25m coil, at the price shown for that length, so a whole opening can be sealed with a single joint.
Which panel thickness does it fit?
Edges from 1mm to 2mm. Thinner sheet will not be gripped firmly, and thicker sheet will not seat fully in the 4mm channel. Measure with calipers if unsure.
How far should the bulb be squashed?
By 30% to 40% when the door or lid is closed. The bulb is roughly 7mm across, so that is about 2mm to 3mm of squash. Squashing it harder makes the sponge take a permanent set and stop sealing.
Do I need adhesive?
No. The steel carrier and internal gripping fingers hold it on the edge. Adhesive is only worth adding where the edge is shorter than the 9.5mm channel depth.
Can it be used outdoors?
Yes. Both the solid grip and the sponge bulb are EPDM, passed the ASTM D1149 ozone test with no cracks, and are rated from -40°C to +80°C.
How do I cut and join it?
Cut through the steel carrier with heavy-duty side cutters or a fine hacksaw, not scissors. Butt the two ends tightly together; for a fully sealed joint, add a little flexible sealant or instant adhesive suitable for EPDM to the bulb ends.
Will it go round corners?
Yes, it follows radiused corners without cutting. For a tight 90° corner, notch the grip only so the bulb continues round unbroken.
Is it suitable for fuel or oil?
No. EPDM swells in petrol, diesel and mineral oils. It is fine with water, detergents, most household chemicals and weather.
When will it be dispatched?
It is held in stock in the UK; see the dispatch message by the Add to basket button.
Need help choosing the right edge seal? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-IPSGT-22.5-11 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip EPDM Top Seal – 22.5mm High – Offset Sponge Bulb, Fits 1-2mm Panels – 11m to 25m