
Rubber & FoamSKU IP-SGTS-12X21-9M
Self-Grip EPDM Top Seal – 12mm x 21mm – Sponge Bulb, Fits 1.6-3mm Panels – 9m to 25m
Price shown updates with the option you pick.
A push-on edge seal for 1.6 mm to 3 mm panels: a solid EPDM rubber clip with a steel carrier inside, topped by a soft, hollow sponge EPDM bulb with two sealing lips. The clip grips the edge with no glue. When a door, hatch, lid or window closes onto the bulb, the bulb squashes and makes a watertight, draught-proof line. The section is 12 mm wide across the lips and 21 mm high, with an 8 mm bulb section, a 10.5 mm deep channel and a 5 mm channel opening. Choose one continuous length from 9 m to 24 m, or a full 25 m coil. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet, panel and flange edges 1.6 mm to 3 mm thick
- Size: 12 mm wide × 21 mm high; 8 mm bulb section; 10.5 mm channel depth; 5 mm channel opening
- Construction: solid EPDM grip (80 ± 5° Shore A) over a U-shaped steel carrier, with four gripping barbs inside and a closed-cell sponge EPDM bulb with twin lips on top
- Seals best when the closed gap squeezes the bulb by 30–40 %
- Working temperature: −40 °C to +80 °C; ozone-tested EPDM for outdoor use
- Price: £24.60 per metre inc VAT for 9 m to 24 m. The full 25 m coil is £472.50 (£18.90 per metre), so it costs less than any cut length from 20 m up.
Technical drawing

How it fits

- Clean the edge and file off any burrs.
- Start at a hidden point, such as the bottom of a door, and press the seal onto the edge with your thumbs. Tap it fully home with a rubber or plastic mallet, working along the run.
- Ease it round corners rather than stretching it. Stretched rubber shrinks back later and leaves gaps.
- Cut it to length with heavy-duty snips or side cutters (they go through the steel carrier) and butt the two ends tightly together.
Typical uses
- Doors, hatches and inspection covers on machinery, trailers, horse boxes and electrical enclosures
- Window, glass and roof-panel edges on vans, buses, cabs and site cabins
- Marine lockers, hatches and equipment covers
- Furniture, cabinet doors and safety guards where a sharp edge also needs covering
Which size do I need?
| Profile | Panel | Best for |
|---|---|---|
| 9.5 × 18 mm | 0.8–2 mm | Thinner sheet, smaller gaps |
| 12 × 21 mm (this seal) | 1.6–3 mm | General doors and hatches, small to medium gaps |
| 14 × 32 mm | 0.5–1.5 mm | Thin sheet with a larger gap |
| 17 × 31 mm | 5 mm | Thicker panels |
Specifications
| Property | Value | Test method |
|---|---|---|
| Dimensions and supply | ||
| Overall width (across the lips) | 12 mm | Nominal |
| Overall height | 21 mm | Nominal |
| Bulb section height | 8 mm | Nominal |
| Channel depth | 10.5 mm | Nominal |
| Channel opening | 5 mm | Nominal |
| Panel thickness it fits | 1.6 mm to 3 mm | - |
| Dimensional tolerance | Not stated by the manufacturer; ask us before ordering for a tight fit | - |
| Colour | Black | - |
| Lengths | 9 m to 24 m in one piece (1 m steps), or a full 25 m coil | - |
| Whole profile | ||
| Construction | Solid EPDM grip, closed-cell sponge EPDM bulb, steel carrier | - |
| Hardness range quoted for the profile | 67–82° Shore A | - |
| Operating temperature | −40 °C to +80 °C | - |
| Recommended bulb compression | 30–40 %; 40 % maximum in normal service (never above 50 %) | - |
| Compression set (7 days at 70 °C) | 50 % max | ASTM D1056 |
| Migration stain on painted finishes | Satisfactory | ASTM D925 |
| Contact stain on painted finishes | Satisfactory | ASTM D925 |
| Colour fastness | Satisfactory | ASTM D750 |
| Solid EPDM grip section | ||
| Hardness | 80 ± 5° Shore A | ASTM D2240 |
| Tensile strength | 80 kg/cm² min (about 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm min (about 29 kN/m) | ASTM D624 |
| Brittle point | −40 °C | ASTM D746 |
| Compression set | 40 % max | ASTM D395 Type B |
| After air ageing 70 h at 70 °C: hardness change | +2° Shore A | - |
| After air ageing 70 h at 70 °C: tensile change | +15 % | - |
| Ozone resistance (70 h at 50 °C, 50 pphm, 20 % stretch) | No cracks | ASTM D1149 |
| Elongation at break | Not stated by the manufacturer | - |
| Sponge EPDM sealing bulb | ||
| Density (indicative) | 550–600 kg/m³ (0.55–0.60 g/cm³)* | - |
| Tensile strength | 7–10 kg/cm² (about 0.7–1.0 MPa) | ASTM D412 |
| Tear resistance | 0.6–0.8 kg/mm (about 5.9–7.8 kN/m) | ASTM D624 |
| Water absorption (22 h at 23 °C) | 1.2 % max | ASTM D1056 |
| Brittle point | −40 °C | ASTM D746 |
| Ozone resistance (70 h at 50 °C, 50 pphm, 50 % stretch) | No cracks | ASTM D1149 |
| Steel carrier | ||
| Grade | Fe 50 to UNI 5961-67 | - |
| Hardness | 80–90 HRB (Rockwell B) | - |
| Tensile strength | 50 kg/mm² min (about 490 MPa) | - |
All values are from the manufacturer's data for this profile. Metric conversions in brackets are ours. *The manufacturer's sheet prints the sponge density unit as g/cm³; 550–600 can only be kg/m³ for a sponge, so we show it that way. The product data gives 67–82° Shore A for the profile and 80 ± 5° for the solid grip, and 40 % as the maximum compression while the data sheet gives 50 %; we show both so you can design to the safer figure.
Materials and compliance
The grip is solid EPDM rubber and the bulb is closed-cell sponge EPDM, extruded together over a U-shaped Fe 50 steel carrier. EPDM is chosen for outdoor seals because it resists sunlight, ozone, rain and frost. Both rubber parts of this profile have passed the ASTM D1149 ozone test with no cracking, and the profile is rated satisfactory in the ASTM D925 staining tests, so it is suited to painted panels.
The manufacturer states no food-contact, fire-rating, WRAS, REACH or other approvals for this profile, so we do not claim any. If you need a certified material, call or email us and we will suggest a seal that has it.
How much do I need?
Measure the full length of edge to be sealed and add 5–10 % for corners and trimming. Each length is supplied as one continuous piece, so a whole door or hatch can be sealed with only one joint. For example, three 600 mm × 1,200 mm cabinet doors have a total perimeter of 10.8 m, so the 12 m length covers them with spare for trimming. If you need 20 m or more, the 25 m coil is the cheaper choice.
Frequently asked questions
Do I need glue or clips to fit it?
No. The steel carrier and the four barbs inside the channel clamp the edge, so it stays on by grip alone. On edges that see heavy vibration, a few dots of contact adhesive in the channel add extra hold.
What panel thickness does it fit?
Any edge from 1.6 mm to 3 mm thick, which covers most sheet steel, aluminium, GRP and plywood-faced panels in that range. The edge must be at least 10.5 mm deep so the channel can seat fully. Below 1.6 mm it can work loose; above 3 mm it will not push fully home.
How big a gap should the bulb seal?
The sealing head stands 8 mm above the grip. Size the gap so the closed door or lid squeezes it by 30–40 %, roughly 2.5–3 mm of squash. Squeezing it more than 40 % in service makes the sponge take a permanent set, and it must never go past 50 %.
Will it go round corners?
Yes. The steel carrier lets it bend round curves and corners without kinking. Bend it rather than cutting and mitring, and keep the bulb facing the closing surface.
How do I cut and join it?
Cut it with heavy-duty snips or side cutters, which go through the rubber and steel carrier cleanly. Butt the two ends together at a hidden point; a dab of cyanoacrylate rubber adhesive on the sponge faces closes the joint fully.
What temperatures and weather can it take?
It works from −40 °C to +80 °C. EPDM is weather, UV and ozone resistant, so it is suited to outdoor doors and hatches. It is not suited to oil or fuel contact.
Is it one piece or joined?
Each length from 9 m to 24 m, and the 25 m coil, is one unbroken piece.
Need help choosing a seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SGTS-12X21-9M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip EPDM Top Seal – 12mm x 21mm – Sponge Bulb, Fits 1.6-3mm Panels – 9m to 25m