
Rubber & FoamSKU IP-EPDM-7.5X15X4.5-STD
EPDM Square U Channel – 7.5mm x 15mm for 4.5mm Panels – 50m Coil
A tall, solid black EPDM square U channel that pushes onto 4.5 mm panel and sheet edges and grips them deeply. It is 7.5 mm wide and 15 mm high, with a 4.5 mm slot that runs 13.5 mm deep, 1.5 mm walls on each side and a 1.5 mm solid base over the cut edge. The result is a neat, square, cushioned finish that hides sharp or rough edges and stays put on long runs. EPDM works from −40 °C to +120 °C and resists weather and ozone, so it suits warm machinery as well as outdoor doors and hatches. It comes as one continuous 50 m coil, held in stock in the UK for same-day dispatch.
At a glance
- Fits: panels, sheet and glazing 4.5 mm thick
- Size: 7.5 mm wide × 15 mm high; 4.5 × 13.5 mm slot; 1.5 mm walls; 1.5 mm base
- Material: solid EPDM rubber, 65° Shore A, black
- Strength: 9 MPa tensile strength
- Temperature: −40 °C to +120 °C
- Weight: 74 g per metre, about 3.7 kg per coil
- Supplied as: one continuous 50 m coil, about £7.14 per metre
- Push-on fit with no tools. It cuts cleanly with a knife and is 100 % recyclable.
Technical drawing

All dimensions are in mm and nominal. The 13.5 mm slot depth is the 15 mm height minus the 1.5 mm base. The 1.5 mm walls are the 7.5 mm width minus the 4.5 mm slot, split over two walls, and match the manufacturer's stated 1.5 mm thickness. The drawing is not to scale.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Square U channel: straight parallel walls, parallel slot, flat base | Manufacturer drawing |
| Overall width | 7.5 mm | Manufacturer drawing and listing |
| Overall height | 15 mm | Manufacturer drawing and listing |
| Slot (channel) width | 4.5 mm | Manufacturer drawing and listing |
| Slot depth (grip depth) | 13.5 mm | Calculated: 15 − 1.5 mm base |
| Wall thickness | 1.5 mm each side | Manufacturer ("thickness 1.5 mm"); matches (7.5 − 4.5) ÷ 2 |
| Base thickness over the edge | 1.5 mm | Manufacturer drawing |
| Panel thickness it fits | 4.5 mm | Manufacturer |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer |
| Colour | Black | Manufacturer |
| Hardness | 65° Shore A | Manufacturer; method not stated |
| Tensile strength | 9 MPa | Manufacturer; method not stated |
| Maximum working temperature | +120 °C | Manufacturer |
| Minimum working temperature | −40 °C | Manufacturer |
| Weight | 74 g per metre (about 3.7 kg per 50 m coil) | Manufacturer; coil weight calculated |
| Elongation at break | Not stated for this profile | Ask us if you need it |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Compression set | Not stated for this profile | Ask us if you need it |
| Density | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated for this profile; dimensions are nominal | Ask us if you need it |
| Supplied as | One continuous 50 m coil | — |
Price
| Pack | Price inc VAT | Per metre | Approx. weight |
|---|---|---|---|
| 50 m coil | £357.18 | £7.14 | 3.7 kg |
Need less than 50 m? Our EPDM square U channel for 4.5 mm panels, 15 mm high with 2 mm walls is sold by the metre (its walls are thicker, so the finished edge is wider).
Materials and compliance
This profile is made from solid EPDM, a synthetic rubber known for its resistance to weather, ozone and UV. The manufacturer states that it is 100 % recyclable and rates it from −40 °C to +120 °C. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating, REACH, RoHS or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required. Ask us for a certified alternative.
How it fits

- Check the edge. Deburr, clean and dry it, and check the panel is about 4.5 mm thick.
- Push on. Start at one end and press the channel down along the edge by hand. With a 13.5 mm deep slot, a little soapy water helps it slide fully home on long runs. A soft mallet helps too. You need no other tools.
- Cut and join. Cut slightly over-length with a sharp knife or shears, then push the ends together into a tight butt joint.
- Bond if needed. Where there is vibration, or where you need a sealed fit (for example round an aluminium window channel), run a bead of polyurethane or silicone sealant into the slot before fitting.
How much do I need?
Add up every edge you want to cover, allow about 5 % for corners and waste, then divide by 50. For example, 30 hatch covers each 800 mm × 600 mm have 84 m of edge; with 5 % added that is about 89 m, so two 50 m coils.
Typical uses
- Edging 4.5 mm sheet metal doors, hatches, covers and machine guards
- Protecting cut edges on machinery and enclosure panels near heat, up to 120 °C
- Edge protection on 4.5 mm glass, acrylic and polycarbonate panels
- Knock protection on vending machines, cabinets and furniture panels
- Safety edging on stairs, step plates and running boards
- Outdoor trailers, kiosks and equipment covers, where EPDM's weather resistance helps
Which one do I need?
| Profile | Fits panel | Choose it when |
|---|---|---|
| EPDM 6.7 × 15.5 mm | 3 mm | 3 mm sheet, cut lengths |
| EPDM 6.5 × 15.2 mm | 3.5 mm | 3.5 mm sheet, cut lengths |
| TPE 8 × 12 mm | 4 mm | 4 mm panels, 25 m coil |
| EPDM 7.5 × 15 mm (this item) | 4.5 mm | 4.5 mm panels, deep grip, heat up to 120 °C |
FAQ
What thickness of panel does it fit?
It is made for 4.5 mm material. For slightly thinner sheet you can bond a thin rubber strip inside the slot to pack it out. For thicker material choose a channel with a wider slot. To make the finished edge wider, a neoprene strip can be bonded alongside it.
Why choose a 15 mm tall channel?
The extra height gives a 13.5 mm deep slot, so the channel grips much more of the edge than a shallow channel. It is less likely to peel off on long runs, curves or edges that get knocked, and it hides more of a rough or uneven cut.
Will it stay on without glue?
On a clean 4.5 mm edge the deep slot holds by grip alone for most static uses. On moving doors, vibrating machinery or outdoor parts, bond it with polyurethane or silicone sealant.
What temperatures can it take?
The manufacturer rates it from −40 °C to +120 °C, so it suits cold stores, outdoor equipment and panels near warm machinery.
Can it be used outdoors?
Yes. EPDM is one of the most weather-resistant rubbers, with good resistance to sunlight, ozone and rain.
How do I cut and join it?
Cut it with a sharp knife, shears or a fine-tooth saw for a square end. Butt the ends tightly together. For a sealed joint, bond the ends with a flexible adhesive or sealant. To go round a tight corner, mitre the channel or notch the base slightly so it bends without lifting.
Why EPDM rather than TPE?
This EPDM channel is rated up to 120 °C, so it is the better choice near heat or in strong sun. TPE channels are a good alternative for general indoor edging.
Is it oil resistant?
EPDM is not recommended for contact with mineral oils, petrol or diesel. For oily areas, ask us about a nitrile or neoprene channel.
Is it food safe or WRAS approved?
No approvals are stated for this profile, so it should not be used where food-contact or drinking-water certification is needed.
Is it in stock?
Yes. We hold it in stock as a continuous 50 m coil, ready for same-day dispatch.
Need help choosing or fitting? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-EPDM-7.5X15X4.5-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 7.5mm x 15mm for 4.5mm Panels – 50m Coil