
Rubber & FoamSKU IP-EPDMC-9.2X10-10
EPDM Square U Channel – 9.2mm x 10mm for 4.75mm Panels – 10m to 30m Lengths
Price shown updates with the option you pick.
A compact, square-section black EPDM rubber channel that pushes onto 4.75mm panel, sheet and glass edges. At 9.2mm wide and 10mm high, with 2.25mm walls, it boxes in sharp or chipped edges with a neat square bead and cushions knocks. Every order is one continuous length cut to the metre, from 10m to a full 30m coil, and it ships from UK stock.
At a glance
- Fits 4.75mm edges: 4.75mm wide slot, about 7.75mm deep
- Compact square profile: 9.2mm wide x 10mm high, flat sides and square corners
- Sturdy 2.25mm walls: thicker than most trims of this size, for better knock protection
- Solid EPDM, 65–75 IRHD: firm enough to grip, soft enough to cushion
- Outdoor-proof: the datasheet's 72-hour ozone test left no cracks
- Best value at 30m: the full coil costs less than a 26m cut length
Technical drawing

The slot depth (marked ≈) is worked out from the supplier's overall height and 2.25mm thickness. It is not separately measured.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Square U channel (flat sides, square corners) | Manufacturer drawing |
| Overall width | 9.2 mm | Manufacturer datasheet |
| Overall height | 10.0 mm | Manufacturer datasheet |
| Slot (channel) width | 4.75 mm | Manufacturer datasheet |
| Fits panel / edge thickness | 4.75 mm | Manufacturer datasheet |
| Wall thickness | 2.25 mm | Manufacturer data (agrees with (9.2 − 4.75) ÷ 2 ≈ 2.2) |
| Slot depth | ≈7.75 mm | Calculated: 10.0 − 2.25 |
| Material | Solid EPDM (ethylene propylene diene monomer), not sponge | Manufacturer datasheet |
| Colour | Black | Manufacturer data |
| Hardness | 65–75 IRHD (±5), listed as 65–75° Shore A | IRHD, manufacturer datasheet |
| Tensile strength | 10 MPa | Manufacturer datasheet |
| Elongation at break | 500% | Manufacturer datasheet |
| Tear strength | 50 kN/m | Manufacturer datasheet |
| Compression set | 21% | 22 h at 70 °C, manufacturer datasheet |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm, manufacturer datasheet |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C, manufacturer datasheet |
| Heat ageing: change in elongation | 0% | 70 h at 70 °C, manufacturer datasheet |
| Weight | 0.08 kg per metre (a 30m coil is about 2.4 kg) | Manufacturer data |
| Lengths available | 10m to 29m in 1m steps, plus a 30m full coil; each one continuous piece | Our stock |
| Dimensional tolerance | Not stated by the manufacturer for this profile | Not available |
| Service temperature | About −40 °C to +100 °C (typical for EPDM, not tested on this profile) | General EPDM data |
| Density | Not stated by the manufacturer for this profile | Not available |
Materials and compliance
This channel is made from a solid black EPDM compound. EPDM is known for resisting weather, UV, ozone, water and steam, and it stays flexible in cold weather. It is not suited to petrol, mineral oils or hydrocarbon solvents. If it will be splashed with oil, ask us about a nitrile or neoprene alternative.
The manufacturer works under an ISO 9001:2015 registered quality system. It does not state FDA, EC 1935/2004, WRAS, UL 94, REACH or RoHS compliance for this product, so we make no such claims. If you need a declaration for your project, contact us before you order.
Fitted on a 4.75mm edge

Typical uses
- Edge protector for 4.75mm (3/16") steel, aluminium and plastic guard or enclosure panels
- Edge trim for 4–5mm glass, polycarbonate and acrylic screens and shelves
- Edges of doors, hatches, cabinet fronts, display units and vending machines
- Stair nosings, running boards and thin plywood or hardboard panel edges
- A finishing seal around aluminium window channels when bonded in place
Price per metre
| Length | Price inc VAT | Per metre |
|---|---|---|
| 10m to 29m cut lengths | £174.24 (10m) to £505.29 (29m) | £17.42/m |
| 30m full coil | £451.80 | £15.06/m |
The 30m coil costs less than any cut length from 26m up. If you need 26m or more, the full coil is the cheaper choice.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Example: three cabinet doors 1.2m x 0.6m, edged all round, need 3 x 3.6m = 10.8m. Add 5% to get 11.3m, so order 12m. Each length is one unbroken piece, so you can run it round corners and cut it on site.
Fitting
- Check the edge is 4.75mm thick (3/16"). A 3–4mm edge will be loose unless you bond a thin strip inside the slot.
- Wipe the edge free of dust, oil and swarf, and file off any burrs.
- Start on a straight run. Press the channel on by hand and seat it with a rubber mallet.
- On outside corners, cut a small V-notch out of the base so the profile bends without kinking.
- For a permanent or watertight fit, run a thin bead of polyurethane or silicone sealant into the slot first.
Similar sizes for 4.75mm edges
| Profile | Choose it when |
|---|---|
| EPDM square U 9.2mm x 10mm (this item) | You want a compact square bead with 2.25mm walls, on a 10m–30m length |
| U channel 4.75mm x 7.75mm inside, square section | You only need a few metres, sold by the metre |
| EPDM square U channel 8.75mm x 14mm | You want a deeper 12mm grip for a firmer hold |
| Square channel edge trim 13mm x 11mm | You need heavier walls for real impact protection |
| EPDM square U channel 9.2mm x 15mm | Your panels are 6mm thick |
Questions
Will it fit a 4mm, 5mm or 6mm panel?
It is made for 4.75mm (3/16") edges. A 5mm edge will usually push in with a little more effort. On 4mm it will be loose unless you bond a thin strip inside the slot or glue it on. For 6mm panels choose the 9.2mm x 15mm channel.
How do I fit it?
Push it on by hand and seat it with a rubber mallet. It grips by friction. Add polyurethane or silicone sealant in the slot where it must resist vibration or keep water out.
Can I use it outdoors?
Yes. EPDM resists weather, UV and ozone, and the manufacturer's 72-hour ozone test showed no cracking.
What temperatures will it take?
The manufacturer does not give a range for this profile. EPDM typically works from about −40 °C to +100 °C, and heat-aged samples (70 h at 70 °C) kept their elongation unchanged. Ask us if your application runs hotter.
How do I cut or join it?
Cut it with a sharp knife, heavy scissors or fine-toothed snips against a straight edge. Butt-join ends with a cyanoacrylate rubber adhesive. On corners, notch the base rather than cutting it right through, so the run stays continuous.
Is it solid rubber or sponge?
Solid EPDM throughout, rated 65–75 IRHD. That is firm enough to stay put and soft enough to absorb knocks.
What applications does it suit?
Sheet metal, guard and enclosure edges, 4–5mm glass and plastic panels, doors, stairs, furniture and vending machines. It is not for oily environments. Choose nitrile or neoprene there.
Will it arrive as one piece?
Yes. Every length from 10m to 30m is supplied as one continuous, unjoined piece, loosely coiled.
Is it food safe or WRAS approved?
The manufacturer does not state any food-contact or water approval for this product, so we cannot claim one.
Need help choosing? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk with your panel thickness and application.
Product details
| SKU | IP-EPDMC-9.2X10-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 9.2mm x 10mm for 4.75mm Panels – 10m to 30m Lengths