
Rubber & FoamSKU IP-EPDMU-8.75X14-8
EPDM Square U Channel – 8.75mm x 14mm – Fits 4.75mm Panel – Black Rubber Edge Trim
Price shown updates with the option you pick.
A deep-gripping, square-edged rubber channel for 4.75mm panels. This solid black EPDM U channel is 8.75mm wide and 14mm high. Its 4.75mm slot is 12mm deep, so it holds a long strip of the panel face and stays put better than a shallow trim. The 2mm walls and base give a crisp square edge that soaks up knocks and covers sharp or rough edges on sheet metal, glass, acrylic, polycarbonate and board. EPDM resists rain, UV and ozone, so it works outdoors as well as indoors.
Choose one continuous length from 8m to 30m. The full 30m coil is the best value per metre. Held in UK stock.
At a glance
- Fits: panels and sheet 4.75mm thick (3/16")
- Profile: 8.75mm wide × 14mm high, square outer corners
- Slot: 4.75mm wide × 12mm deep, so it grips 12mm of the panel face on each side
- Walls and base: 2mm solid EPDM
- Hardness: 65–75 Shore A: holds its shape, still cuts with a sharp knife
- Lengths: 8m to 29m in 1m steps, or a full 30m coil, always one continuous piece
Technical drawing

How it fits

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 8.75 mm | Nominal, supplier drawing and data |
| Overall height | 14.0 mm | Nominal, supplier drawing and data |
| Slot (channel) width | 4.75 mm (shown as 4.7 mm on the drawing) | Nominal, supplier data |
| Slot depth | 12.0 mm | Nominal, supplier drawing |
| Wall thickness (each side) | 2.0 mm | Supplier technical data |
| Base thickness | 2.0 mm | Calculated: 14 mm height − 12 mm slot depth |
| Fits panel thickness | 4.75 mm | Supplier data ("to fit panel") |
| Cross-section area | 65.5 mm² | Calculated from the nominal dimensions |
| Material | Solid EPDM (ethylene propylene diene monomer) | Supplier material specification |
| Colour | Black | — |
| Hardness | 65–75 Shore A (65–75 ±5 IRHD) | Supplier material specification (IRHD) |
| Tensile strength | 10 MPa | Supplier material specification |
| Elongation at break | 500 % | Supplier material specification |
| Tear strength | 50 kN/m | Supplier material specification |
| Compression set | 21 % | 22 h at 70 °C (supplier material specification) |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm ozone |
| Heat ageing: change in tensile strength | +9 % | 70 h at 70 °C |
| Heat ageing: change in elongation | 0 % | 70 h at 70 °C |
| Weight | 0.09 kg per metre (about 2.7 kg for 30 m) | Supplier data |
| Density | About 1.37 g/cm³ | Calculated from 0.09 kg/m and 65.5 mm² area |
| Service temperature | About −40 °C to +120 °C | Typical for EPDM, not tested on this profile |
| Dimensional tolerance | Not stated by the manufacturer; nominal sizes | Ask us if you need a toleranced drawing |
| Minimum length | 8 m | Supplier data |
| Supplied as | One continuous length, 8 m to 30 m | — |
Materials and compliance
Made from a solid EPDM rubber compound, which the manufacturer describes as 100% recyclable. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so please do not specify it where one of those is required. If you need a certified grade, call us and we will suggest one.
Which length, and what does it cost per metre?
| Length | Price inc VAT | Per metre |
|---|---|---|
| 8m | £174.63 | £21.83 |
| 10m | £218.31 | £21.83 |
| 15m | £327.45 | £21.83 |
| 20m | £436.59 | £21.83 |
| 25m | £545.73 | £21.83 |
| 29m | £633.06 | £21.83 |
| 30m full coil | £572.40 | £19.08 |
Every length from 8m to 29m works out at about £21.83 per metre. The full 30m coil costs less than 27m, so if you need 27m or more, buy the coil. To work out how much you need, add up the edges you want to cover and allow about 5% for trimming. For example, all four sides of two 1.5m × 0.8m guard panels is 9.2m; with 5% spare, choose 10m.
How to fit it
- Clean the edge and remove burrs, grease and dust.
- Start at one end and press the channel onto the edge with your thumbs, pushing the full 12mm depth home as you work along. A soft rubber mallet helps on long runs.
- Go round gentle curves in one piece. On a sharp corner, cut a V notch out of the walls (not the base) so the channel folds neatly.
- Cut square with a sharp knife or snips and butt the ends tightly together.
- For a permanent fix or a weather seal, run a bead of polyurethane or silicone sealant in the slot before you push it on.
Typical uses
- Edges of 4.75mm (3/16") aluminium, steel and stainless sheet
- Acrylic and polycarbonate machine guards, screens and display panels
- Glass and glazing edges in frames, cabinets and shelving
- Vending machines, kiosks, enclosures and equipment covers
- Doors, hatches, stair edges and furniture panels
- Trailers, horseboxes, boats and caravans
Similar sizes
| Profile (W × H) | Fits panel | Choose it when |
|---|---|---|
| 7.5mm × 15mm | 4.5mm | Your panel is slightly thinner and you want a 50m coil |
| 8.75mm × 14mm (this item) | 4.75mm | You want a deep 12mm grip on 4.75mm sheet |
| 8mm × 9mm | 5mm | You want a low, neat edge on 5mm sheet |
| 9.2mm × 15mm | 6mm | Your panel is 6mm thick |
Need less than 8m? Our 9mm × 14mm EPDM U channel for 4.75mm panels is sold by the metre.
Frequently asked questions
What panel thickness does it fit?
4.75mm (3/16"). The slot is 4.75mm wide, so it grips that thickness snugly. On 4mm or 4.5mm material, fit it with a bead of sealant in the slot; for 5mm or 6mm choose a wider channel from the table above.
Will it stay on without glue?
On a clean edge the 12mm-deep slot holds by friction for most guarding and trim jobs. Where it will be knocked often, pulled or exposed to weather, bond it in with polyurethane or silicone sealant.
How do I cut and join it?
A sharp craft knife, snips or a fine-toothed saw all cut it cleanly. Butt the ends together on a straight run. For a sealed joint, use a dab of instant adhesive for rubber on the end faces.
Can it go round corners?
It follows gentle curves in one piece. For a 90° corner, cut a V notch out of both walls so the base bends, or mitre two pieces at 45°.
Is it suitable for outdoor use?
Yes. EPDM has very good resistance to weather, UV and ozone; the material passed the supplier's 72-hour ozone test with no cracks.
What temperature can it take?
The manufacturer does not give a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, and this compound kept its strength after 70 hours at 70 °C.
Is it oil resistant?
No. EPDM swells in mineral oil, petrol and diesel. It is good with water, steam, mild acids and alkalis. For oily areas, ask us about a nitrile or neoprene channel.
Is it food safe?
No food-contact approval is stated for this product, so do not use it where it touches food.
Can I buy less than 8 metres?
The shortest length of this profile is 8m. For short runs, see the by-the-metre 9mm × 14mm channel above.
Is it one piece?
Yes. Whatever length you choose comes as one continuous piece, coiled for delivery.
Need a different size or a toleranced drawing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMU-8.75X14-8 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 8.75mm x 14mm – Fits 4.75mm Panel – Black Rubber Edge Trim