
Rubber & FoamSKU IP-EPDMU-9.5X19-7
EPDM Square U Channel – 9.5mm x 19mm – Fits 6.3mm Panel – Black Rubber Edge Trim
Price shown updates with the option you pick.
A deep-grip, square-section black EPDM rubber channel for 6.3mm (¼ inch) panel, sheet and glass edges. It is 9.5mm wide and 19mm tall, so its thin 1.6mm legs reach 17.4mm down each face of the panel. That holds far more firmly than a shallow trim and covers scuffed or uneven edges. Every order is one continuous length cut to the metre, from 7m to a full 30m coil, and it ships from UK stock.
At a glance
- Fits 6.3mm edges: 6.3mm wide slot, 17.4mm deep
- Deep grip: 9.5mm wide x 19mm high, flat sides and square corners
- Thin, even walls: 1.6mm each side, so it adds only 3.2mm to the panel thickness
- Solid EPDM, 65–75 IRHD: firm enough to grip, soft enough to cushion knocks
- Outdoor-proof: no cracks after the manufacturer's 72-hour ozone test
- Best value at 30m: the full coil costs less than a 26m cut length
Technical drawing

The base value marked ≈ is worked out from the manufacturer's overall height and slot depth (19 − 17.4). It is not separately measured.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Square U channel (flat sides, square corners) | Manufacturer drawing |
| Overall width | 9.5 mm | Manufacturer datasheet |
| Overall height | 19.0 mm | Manufacturer datasheet |
| Slot (channel) width | 6.3 mm | Manufacturer datasheet |
| Slot depth | 17.4 mm | Manufacturer drawing |
| Fits panel / edge thickness | 6.3 mm (¼ in) | Manufacturer datasheet |
| Wall thickness | 1.6 mm each side | Manufacturer data; matches (9.5 − 6.3) ÷ 2 |
| Base thickness | ≈1.6 mm | Calculated: 19.0 − 17.4 |
| Material | Solid EPDM (ethylene propylene diene monomer), not sponge | Manufacturer datasheet |
| Colour | Black | Manufacturer data |
| Hardness | 65–75 IRHD (±5), listed as 65–75° Shore A | IRHD, manufacturer datasheet |
| Tensile strength | 10 MPa | Manufacturer datasheet |
| Elongation at break | 500% | Manufacturer datasheet |
| Tear strength | 50 kN/m | Manufacturer datasheet |
| Compression set | 21% | 22 h at 70 °C, manufacturer datasheet |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm, manufacturer datasheet |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C, manufacturer datasheet |
| Heat ageing: change in elongation | 0% | 70 h at 70 °C, manufacturer datasheet |
| Weight | 0.11 kg per metre (a 30m coil weighs about 3.3kg) | Manufacturer data |
| Lengths available | 7m to 29m in 1m steps, plus a 30m full coil; each one continuous piece | Our stock |
| Service temperature | About −40 °C to +100 °C (typical for EPDM, not tested on this profile) | General EPDM data |
| Density | Not stated by the manufacturer for this profile | Not available |
Materials and compliance
This channel is made from a solid black EPDM compound. EPDM is known for resisting weather, UV, ozone, water and steam, and it stays flexible in cold weather. It is not suited to petrol, mineral oils or hydrocarbon solvents. If it will be splashed with oil, ask us about a nitrile or neoprene alternative.
The manufacturer works under an ISO 9001:2015 registered quality system. It does not state FDA, EC 1935/2004, WRAS, UL 94, REACH or RoHS compliance for this product, so we make no such claims. If you need a declaration for your project, contact us before you order.
Fitted on a 6.3mm edge

Typical uses
- Edge protector for 6mm and ¼ inch steel, aluminium and plastic guard or enclosure panels
- Edge trim for 6mm toughened glass, polycarbonate and acrylic screens, shelves and partitions
- Rough or uneven edges where a shallow trim would not cover the damage
- Edges of doors, hatches, cabinet fronts, display units and vending machines
- Stair nosings, running boards and plywood or MDF panel edges
- A finishing seal around aluminium window channels when bonded in place
Price per metre
| Length | Price inc VAT | Per metre |
|---|---|---|
| 7m to 29m cut lengths | £196.47 (7m) to £813.93 (29m) | £28.07/m |
| 30m full coil | £729.00 | £24.30/m |
The 30m coil costs less than any cut length from 26m up. If you need 26m or more, the full coil is the cheaper choice. For runs shorter than 7m, see our 6.3mm x 17.4mm U channel sold per metre.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Example: four guard panels 1.0m x 0.8m, edged all round, need 4 x 3.6m = 14.4m. Add 5% to get 15.1m, so order 16m. Each length is one unbroken piece, so you can run it round corners and cut it on site.
Fitting
- Check the edge is 6.3mm thick. A 5mm edge will be loose unless you bond a thin strip inside the slot.
- Wipe the edge free of dust, oil and swarf.
- Start on a straight run. Press the channel on by hand and seat it down the full 17.4mm with a rubber mallet.
- On outside corners, cut a small V-notch out of the legs so the profile bends without kinking.
- For a permanent or watertight fit, run a thin bead of polyurethane or silicone sealant into the slot first.
Similar sizes for 6mm edges
| Profile | Choose it when |
|---|---|
| EPDM square U 9.5mm x 19mm (this item) | You want the deepest grip, on 7m to 30m lengths |
| EPDM square U channel 9.2mm x 15mm | A slightly shallower slot is enough, on a 50m coil |
| EPDM square U channel 9mm x 8mm | You want the lowest, neatest profile |
| Neoprene U channel 6.3mm x 11mm inside | You need some oil resistance, sold by the metre |
| Square U channel, 6mm panel x 16mm, 3.1mm wall | You need heavy walls for real impact protection |
Questions
Will it fit a 5mm or 8mm panel?
No, not on its own. The slot is 6.3mm. On a 5mm edge it will be loose unless you bond a 1mm strip inside it. On anything thicker than about 6.5mm it will not go on properly.
Why choose a 19mm-tall channel?
The legs cover 17.4mm of each face, against about 6mm for a low-profile trim. That gives a much stronger friction grip and hides chipped or uneven edges. Choose it where the trim must stay on through knocks and vibration.
How do I fit it?
Push it on by hand and seat it with a rubber mallet. It grips by friction. Add polyurethane or silicone sealant in the slot where it must resist vibration or keep water out.
Can I use it outdoors?
Yes. EPDM resists weather, UV and ozone, and the manufacturer's 72-hour ozone test showed no cracking.
What temperatures will it take?
The manufacturer does not give a range for this profile. EPDM typically works from about −40 °C to +100 °C, and heat-aged samples (70 h at 70 °C) kept their elongation unchanged. Ask us if your application runs hotter.
How do I cut or join it?
Cut it with a sharp knife or fine-toothed snips against a straight edge. Butt-join ends with a cyanoacrylate rubber adhesive. On corners, notch the legs rather than cutting right through, so the run stays continuous.
Is it solid rubber or sponge?
Solid EPDM throughout, rated 65–75 IRHD. That is firm enough to stay put and soft enough to absorb knocks.
What applications does it suit?
Sheet metal, guard and enclosure edges, 6mm glass and plastic panels, doors, stairs, furniture and vending machines. It is not for oily environments. Choose nitrile or neoprene there.
Will it arrive as one piece?
Yes. Every length from 7m to 30m is supplied as one continuous, unjoined piece, loosely coiled.
Is it food safe or WRAS approved?
The manufacturer does not state any food-contact or water approval for this product, so we cannot claim one.
Need help choosing? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk with your panel thickness and application.
Product details
| SKU | IP-EPDMU-9.5X19-7 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 9.5mm x 19mm – Fits 6.3mm Panel – Black Rubber Edge Trim