
Rubber & FoamSKU IP-EPDMU-9X8X6-25
EPDM Square U Channel – 9mm x 8mm – Fits 6mm Panel – Black Rubber Edge Trim
Price shown updates with the option you pick.
A slim, square-section black EPDM rubber channel that pushes onto 6mm panel, sheet and glass edges. At 9mm wide and 8mm high it covers sharp or chipped edges with a neat, low-profile bead and takes the sting out of knocks. Every order is one continuous length cut to the metre, from 25m to a full 50m coil, and it ships from UK stock.
At a glance
- Fits 6mm edges: 6mm wide slot, about 6.4mm deep
- Low profile: 9mm wide x 8mm high, flat sides and square corners
- Solid EPDM, 65–75 IRHD: firm enough to grip, soft enough to cushion
- Outdoor-proof: the datasheet's 72-hour ozone test left no cracks
- Light: 0.039kg per metre, so a 50m coil weighs about 2kg
- Best value at 50m: the full coil costs less than a 38m cut length
Technical drawing

Values marked ≈ are worked out from the supplier's overall size, slot width and thickness. They are not separately measured.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile | Square U channel (flat sides, square corners) | Manufacturer drawing |
| Overall width | 9.0 mm | Manufacturer datasheet |
| Overall height | 8.0 mm | Manufacturer datasheet |
| Slot (channel) width | 6.0 mm | Manufacturer data |
| Fits panel / edge thickness | 6 mm | Manufacturer datasheet |
| Thickness (base) | 1.6 mm | Manufacturer data |
| Side wall | ≈1.5 mm each side | Calculated: (9.0 − 6.0) ÷ 2 |
| Slot depth | ≈6.4 mm | Calculated: 8.0 − 1.6 |
| Material | Solid EPDM (ethylene propylene diene monomer), not sponge | Manufacturer datasheet |
| Colour | Black | Manufacturer data |
| Hardness | 65–75 IRHD (±5), listed as 65–75° Shore A | IRHD, manufacturer datasheet |
| Tensile strength | 10 MPa | Manufacturer datasheet |
| Elongation at break | 500% | Manufacturer datasheet |
| Tear strength | 50 kN/m | Manufacturer datasheet |
| Compression set | 21% | 22 h at 70 °C, manufacturer datasheet |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm, manufacturer datasheet |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C, manufacturer datasheet |
| Heat ageing: change in elongation | 0% | 70 h at 70 °C, manufacturer datasheet |
| Weight | 0.039 kg per metre | Manufacturer data |
| Lengths available | 25m to 49m in 1m steps, plus a 50m full coil; each one continuous piece | Our stock |
| Service temperature | About −40 °C to +100 °C (typical for EPDM, not tested on this profile) | General EPDM data |
| Density | Not stated by the manufacturer for this profile | Not available |
Materials and compliance
This channel is made from a solid black EPDM compound. EPDM is known for resisting weather, UV, ozone, water and steam, and it stays flexible in cold weather. It is not suited to petrol, mineral oils or hydrocarbon solvents. If it will be splashed with oil, ask us about a nitrile or neoprene alternative.
The manufacturer works under an ISO 9001:2015 registered quality system. It does not state FDA, EC 1935/2004, WRAS, UL 94, REACH or RoHS compliance for this product, so we make no such claims. If you need a declaration for your project, contact us before you order.
Fitted on a 6mm edge

Typical uses
- Edge protector for 6mm steel, aluminium and plastic guard or enclosure panels
- Edge trim for 6mm toughened glass, polycarbonate and acrylic screens and shelves
- Edges of doors, hatches, cabinet fronts, display units and vending machines
- Stair nosings, running boards and plywood or MDF panel edges
- A finishing seal around aluminium window channels when bonded in place
Price per metre
| Length | Price inc VAT | Per metre |
|---|---|---|
| 25m to 49m cut lengths | £235.14 (25m) to £460.86 (49m) | £9.41/m |
| 50m full coil | £353.94 | £7.08/m |
The 50m coil costs less than any cut length from 38m up. If you need 38m or more, the full coil is the cheaper choice.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Example: eight cabinet panels 0.6m x 1.2m, edged all round, need 8 x 3.6m = 28.8m. Add 5% to get 30.2m, so order 31m. Each length is one unbroken piece, so you can run it round corners and cut it on site.
Fitting
- Check the edge is 6mm thick. A 4–5mm edge will be loose unless you bond a thin strip inside the slot.
- Wipe the edge free of dust, oil and swarf.
- Start on a straight run. Press the channel on by hand and seat it with a rubber mallet.
- On outside corners, cut a small V-notch out of the base so the profile bends without kinking.
- For a permanent or watertight fit, run a thin bead of polyurethane or silicone sealant into the slot first.
Similar sizes for 6mm edges
| Profile | Choose it when |
|---|---|
| EPDM square U 9mm x 8mm (this item) | You want the lowest, neatest profile |
| Square U channel, 6mm panel x 10mm high | You want a deeper grip, sold by the metre |
| TPE square U channel 9mm x 11.5mm | You prefer TPE, on a 25m coil |
| EPDM square U channel 9.2mm x 15mm | You want a deep slot for a firmer hold |
| Square U channel, 6mm panel x 16mm, 3.1mm wall | You need heavy walls for real impact protection |
Questions
Will it fit a 5mm or 8mm panel?
No, not on its own. The slot is 6mm. On a 5mm edge it will be loose unless you bond a 1mm strip inside it. On anything thicker than about 6.5mm it will not go on properly. For 5mm, see our 8mm x 9mm channel.
How do I fit it?
Push it on by hand and seat it with a rubber mallet. It grips by friction. Add polyurethane or silicone sealant in the slot where it must resist vibration or keep water out.
Can I use it outdoors?
Yes. EPDM resists weather, UV and ozone, and the manufacturer's 72-hour ozone test showed no cracking.
What temperatures will it take?
The manufacturer does not give a range for this profile. EPDM typically works from about −40 °C to +100 °C, and heat-aged samples (70 h at 70 °C) kept their elongation unchanged. Ask us if your application runs hotter.
How do I cut or join it?
Cut it with a sharp knife or fine-toothed snips against a straight edge. Butt-join ends with a cyanoacrylate rubber adhesive. On corners, notch the base rather than cutting it right through, so the run stays continuous.
Is it solid rubber or sponge?
Solid EPDM throughout, rated 65–75 IRHD. That is firm enough to stay put and soft enough to absorb knocks.
What applications does it suit?
Sheet metal, guard and enclosure edges, 6mm glass and plastic panels, doors, stairs, furniture and vending machines. It is not for oily environments. Choose nitrile or neoprene there.
Will it arrive as one piece?
Yes. Every length from 25m to 50m is supplied as one continuous, unjoined piece, loosely coiled.
Is it food safe or WRAS approved?
The manufacturer does not state any food-contact or water approval for this product, so we cannot claim one.
Need help choosing? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk with your panel thickness and application.
Product details
| SKU | IP-EPDMU-9X8X6-25 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 9mm x 8mm – Fits 6mm Panel – Black Rubber Edge Trim