
Rubber & FoamSKU IP-EPDMU-8X10X3-10
EPDM U Channel – 8mm x 10mm – Fits 3mm Panels – Black Rubber Edge Trim – 10m to 30m
Price shown updates with the option you pick.
A chunky, cushioned push-on edge trim for 3 mm sheet. This solid black EPDM U channel is 8 mm wide and 10 mm high, with a parallel 3 mm slot, 2.5 mm side walls and a solid rounded base. Its teardrop section puts a full, soft bumper over the cut edge, so it protects people from sharp corners and protects the panel from knocks. Choose one continuous length from 10 m to 29 m, or a full 30 m coil. Every length is held in stock in the UK.
At a glance
- Fits 3 mm panels: parallel 3 mm slot, about 7.4 mm deep, grips both faces of the sheet.
- 8 × 10 mm teardrop profile: 2.5 mm side walls and a solid base of about 2.6 mm over the cut edge.
- Solid EPDM, 65–75 Shore A: tensile strength 10 MPa, elongation at break 500%, tear strength 50 kN/m.
- Made for outdoor use: no cracks after a 72 h ozone test, and little change after heat ageing at 70 °C.
- No tools needed: push on by hand and cut with a sharp knife. Bond with PU or silicone sealant for a permanent or sealed fit.
- Any length from 10 m to 30 m: one continuous piece. The 30 m full coil has the lowest price per metre.
Technical drawing

Nominal dimensions in mm, free (unfitted) state. Width, height, slot width and wall thickness are the manufacturer's figures. Slot depth and base thickness (marked ≈) are scaled from the manufacturer's drawing and are approximate.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | Teardrop (round-back) U channel edge trim | Manufacturer's drawing |
| Overall width | 8 mm | Manufacturer's drawing, nominal |
| Overall height | 10 mm | Manufacturer's drawing, nominal |
| Slot (channel) width | 3 mm, parallel sides | Manufacturer's drawing and data |
| Slot depth | about 7.4 mm | Scaled from manufacturer's drawing |
| Side wall thickness | 2.5 mm | Manufacturer's technical data ("thickness") |
| Base thickness | about 2.6 mm (10 − 7.4) | Derived from manufacturer's drawing |
| Fits panel thickness | 3 mm | Manufacturer's data sheet |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer's data sheet |
| Colour | Black | – |
| Hardness | 65–75 IRHD (±5), stated as 65–75 Shore A | IRHD, manufacturer's data sheet |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500% | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21% | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C |
| Heat ageing: change in elongation at break | 0% | 70 h at 70 °C |
| Weight | 0.06 kg per metre (30 m coil about 1.8 kg) | Manufacturer's data |
| Lengths available | 10, 11, 12 … 29 m, or a full 30 m coil (one continuous piece) | – |
| Service temperature | about −40 °C to +120 °C, typical for EPDM, not tested on this profile | General EPDM data |
| Density | Not stated for this profile | – |
| Dimensional tolerance | Not stated; extruded rubber is normally made to ISO 3302-1 tolerance classes | – |
Materials and compliance
This profile is extruded from a solid EPDM compound. EPDM resists weathering, ozone, UV and water, and stays flexible over time. The test results in the table come from the manufacturer's data sheet for this profile.
The manufacturer does not state any food-contact, WRAS, REACH, RoHS or fire approval for this product, so we do not claim one. If your application needs a certified material, please contact us before ordering.
How it fits

Choosing your length
Add up the total length of edge to be covered and allow about 5% extra for cutting and joints. For example, a 2,440 × 1,220 mm sheet edged on all four sides needs about 7.3 m, so a 15 m length covers two sheets. The price covers one continuous piece of the length you choose.
| Length | Price inc VAT | Price per metre |
|---|---|---|
| 10 m | £209.88 | £20.99 |
| 15 m | £314.82 | £20.99 |
| 20 m | £419.76 | £20.99 |
| 25 m | £524.70 | £20.99 |
| 29 m | £608.64 | £20.99 |
| 30 m full coil | £543.60 | £18.12 |
Need 26 m or more? The full 30 m coil costs less than any length from 26 m to 29 m.
Typical uses
- Edges of 3 mm steel, aluminium and composite panels on guards, enclosures and machine covers
- 3 mm acrylic and polycarbonate screens, displays and protective shields
- Glass and glazing edges, vending machines, shop fittings and cabinet panels
- Doors, hatches and access panels that need a thick, soft, safe edge
- Stair and step edges, running boards and trailer panels
- Bonded into aluminium window channels as a push-in seal
Fitting
- Deburr and clean the edge. Check the sheet is 3 mm thick.
- Start at a corner and press the channel on with your thumb as you work along.
- On outside corners, ease the trim round the bend. On tight corners, cut a small V-notch out of the legs.
- Cut a few millimetres long with a sharp knife, then push the ends together into a tight butt joint.
- For a sealed or permanent fit, run a bead of PU or silicone sealant into the channel first.
FAQ
What panel thickness does it fit?
3 mm sheet. The slot is 3 mm wide with parallel sides, so it grips a 3 mm edge firmly along its depth. A thinner sheet can be packed out by bonding a thin strip inside the channel.
How do I measure what I need?
Measure the panel thickness with a caliper first, then measure the total edge length in metres and round up. Allow about 5% extra for cuts and joints.
How much of the panel face does it cover?
The slot is about 7.4 mm deep, so the trim covers the edge and about 7 mm of each face once pushed fully home. The finished edge is 8 mm thick.
What is it used for?
Guarding sharp sheet edges on machine guards, enclosures, glazing, vending machines, doors, steps and trailers. Its thick, rounded section makes it a good bumper on edges that people or equipment knock against.
Can it be used outdoors?
Yes. EPDM is chosen for outdoor use because it resists weathering and ozone. This compound passed a 72 h ozone test with no cracks.
What temperatures can it take?
The manufacturer has not published a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, but this has not been tested on this profile. The compound did pass heat ageing for 70 h at 70 °C with little change in properties.
How do I cut and join it?
Use a sharp knife or heavy shears and cut square. Butt the ends together tightly. For a sealed joint, add a little cyanoacrylate glue or sealant to the cut faces.
Is it soft or firm?
At 65–75 Shore A it is medium-firm: soft enough to absorb knocks, and firm enough to hold its shape and grip the panel.
Why is the 30 m coil cheaper than 29 m?
30 m is a full, uncut coil, so there is no cutting or handling, and it is priced lower. If you need 26 m or more, the coil is the cheaper buy.
Is it food-safe or certified?
The manufacturer states no food-contact or other approvals for this product, so we do not claim any. Ask us about certified alternatives.
Is it in stock?
Yes. All lengths are held in stock and dispatched from the UK.
Data sheet
Download the technical data sheet (PDF)
Related profiles
- EPDM U Channel 5.5 × 8.5 mm, for 3 mm panels
- EPDM Square U Channel 6 × 9.5 mm, for 3 mm panels
- EPDM Square U Channel 6.7 × 15.5 mm deep grip, for 3 mm panels
- Neoprene Round U Channel 7.75 × 13.5 mm, for panels up to 3 mm
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMU-8X10X3-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM U Channel – 8mm x 10mm – Fits 3mm Panels – Black Rubber Edge Trim – 10m to 30m