
Rubber & FoamSKU IP-EPDMG-15X13.5-15
EPDM Glazing Weatherstrip Seal 15mm x 13.5mm – For 4.75mm Glass & 1.2–1.6mm Panel – 15m to 30m
Price shown updates with the option you pick.
A compact lock-strip glazing rubber that holds glass up to 4.75 mm thick in a 1.2–1.6 mm metal or plastic panel. The 15 mm × 13.5 mm section has a glass slot on one side, a panel slot on the other and a groove along the top. Once glass and seal are in the aperture, a 7 × 6 mm filler strip is pressed into the groove; it spreads the lips and clamps both edges for an air- and water-tight joint. Made from solid black EPDM for long life outdoors in sun, rain and frost.
- Glass: up to 4.75 mm (3/16 in) – glass, acrylic, polycarbonate
- Panel: 1.2–1.6 mm sheet or flange, 6 mm glass-to-panel clearance
- Tight corners: bends down to a 32 mm radius
- Lengths: one continuous piece, 15 m to 30 m (30 m = full coil, best price per metre)
- In stock in the UK for fast dispatch
Technical drawing

How it fits


Specifications
| Property | Value | Basis / test method |
|---|---|---|
| Overall size (W × H) | 15.0 mm × 13.5 mm | Nominal, supplier drawing |
| Glass slot width | 4.75 mm – takes glass up to 4.75 mm | Supplier drawing |
| Glass slot depth | 4.5 mm | Supplier drawing |
| Panel slot width | 1.6 mm – fits panel 1.2 to 1.6 mm | Supplier drawing |
| Panel slot depth | 6.0 mm | Supplier drawing |
| Glass-to-panel clearance | 6 mm | Supplier data |
| Minimum bend radius | 32 mm | Supplier datasheet |
| Filler / locking strip | 7 mm × 6 mm EPDM filler strip (sold separately) | Supplier data |
| Material | Solid (dense) EPDM – ethylene propylene diene monomer | Supplier datasheet |
| Colour | Black | — |
| Hardness | 65–75 IRHD | Supplier datasheet (IRHD scale; method not stated) |
| Tensile strength | 10 MPa | Supplier datasheet (method not stated) |
| Elongation at break | 500 % | Supplier datasheet (method not stated) |
| Tear strength | 50 kN/m | Supplier datasheet (method not stated) |
| Compression set | 21 % | 22 h at 70 °C, supplier datasheet |
| Service temperature | −40 °C to +90 °C | Supplier data |
| Weight | 0.13 kg per metre (approx. 3.9 kg for a 30 m coil) | Supplier data |
| Lengths available | 15 m to 30 m in 1 m steps, supplied as one continuous length | — |
| Price per metre | £13.17/m inc VAT (15–29 m); £11.88/m on the 30 m full coil | — |
Density, ozone rating and dimensional tolerance class are not published for this profile, so we do not quote them. Typical for dense EPDM, not tested on this profile: very good ozone and UV resistance; not suitable for petrol, mineral oils or greases.
Materials and compliance
Solid black EPDM rubber. The supplier publishes no food-contact, fire-rating, WRAS, REACH or RoHS statement for this profile, so we make no such claim. If you need a certificate of conformity or a specific approval, email us before ordering and we will check what can be supplied.
What you need
- This glazing seal – measure the full perimeter of the aperture and add about 50 mm for the joint.
- Glazing weatherstrip filler strip, 7 mm × 6 mm – the same length as the seal.
- A filler-strip insertion tool (makes feeding the strip far easier), silicone sealant and a little rubber lubricant or soapy water.
Fitting guide
- Strip out. Pull the old filler strip, ease the glass out and remove the old seal. Clean the flange and treat any rust.
- Dry fit. Push the panel slot onto the aperture flange all the way round, pressing it well into the corners.
- Cut. Cut the seal square, about 25 mm beyond where it meets itself, so the ends butt together under slight compression.
- Seal. Lift the seal off, run a small bead of silicone in the panel slot, and refit it with the joint at the top of the aperture.
- Glaze. Run a small bead of silicone in the glass slot, then set the glass in from the bottom and work the lip over the glass edge.
- Lock. Lubricate the groove and, starting at the bottom, feed the filler strip in with an insertion tool. Do not stretch it, or it will shrink back over time. Finish with a tight butt joint, leaving a few millimetres of overlap before pushing the end home.
Questions buyers ask
Will it fit my glass and panel?
It suits glass, acrylic or polycarbonate up to 4.75 mm thick (3/16 in, common on older vehicles, caravans and machinery cabs) set in a panel or flange 1.2 to 1.6 mm thick. If your panel is thinner than 1.2 mm or thicker than 1.6 mm, or your glass is thicker than 4.75 mm, choose a different section – send us your two thicknesses and we will point you to the right one.
Is the filler strip included?
No. The seal will not grip until a 7 × 6 mm filler strip is pressed into the top groove. Order the same length of filler strip as seal.
How much do I need?
Measure round the aperture flange and add about 50 mm. The minimum length is 15 m; above that, buy to the metre, or take the 30 m full coil, which costs less than 28 m.
What is it used for?
Fixed glazing in classic cars, vans, buses, coaches, caravans, horseboxes, tractor and plant cabs, kiosks and machine enclosures – anywhere a flat pane sits in a thin sheet-metal aperture.
Will it go round corners?
Yes, down to a 32 mm radius without kinking. For sharper corners, notch out the panel slot on the inside of the bend or use a moulded corner.
What temperatures and weather can it take?
The supplier rates it from −40 °C to +90 °C. EPDM resists sunlight, ozone, rain and frost, so it stays flexible outdoors for years.
How do I cut and join it?
Cut square with a sharp knife on a board. Make one joint, at the top of the window, with the ends butted under slight compression and sealed with silicone. Do not stretch the seal or filler strip while fitting.
Is it a direct replacement for my old rubber?
Measure the old section's width, height and both slot widths and compare them with the drawing above. This is a generic compatible profile; send us a photo of the cut end if you are unsure.
Related
- Glazing weatherstrip seal 15 × 12.5 mm
- Glazing weatherstrip seal 20 × 17 mm (4.75 mm glass, 0.8–1.6 mm panel)
- Glazing weatherstrip seal 22 × 19 mm
Need a hand choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMG-15X13.5-15 |
|---|---|
| Weight | 4.3 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Glazing Weatherstrip Seal 15mm x 13.5mm – For 4.75mm Glass & 1.2–1.6mm Panel – 15m to 30m