
Rubber & FoamSKU IP-EPDM-20X17-10
EPDM Glazing Weatherstrip Seal 20mm x 17mm – For 4.75mm Glass & 0.8–1.6mm Panel – 10m to 30m
Price shown updates with the option you pick.
A solid black EPDM lock-strip glazing seal, 20mm wide by 17mm high, for setting a glass, acrylic or polycarbonate pane up to 4.75mm thick into a sheet-metal opening of 0.8mm to 1.6mm. The pane sits 6mm deep in one slot and the panel edge 8mm deep in the other; pressing a filler strip into the top groove spreads the lips and clamps both edges into a watertight, rattle-free joint. Every option is one unbroken length, from 10m up to a 30m full coil, held in stock for same-day dispatch.
At a glance
- Size: 20mm wide x 17mm high, round-backed H-section with a filler-strip groove
- Glass slot: 4.75mm wide, 6mm deep - panes up to 4.75mm
- Panel slot: 1.6mm wide, 8mm deep - panels 0.8mm to 1.6mm
- Glass-to-panel clearance: 7mm
- Material: solid EPDM, 65-75 IRHD, -40°C to +90°C
- Bends: minimum bend radius 58mm, so it follows radiused window corners in one piece
- Supplied: one continuous length, 10m to 29m in 1m steps, or a 30m full coil (the 30m coil costs less than 28m or 29m)
Technical drawing


Specifications
| Property | Value | Basis / test method |
|---|---|---|
| Overall width | 20mm | Supplier drawing, nominal |
| Overall height | 17mm | Supplier drawing, nominal |
| Glass slot width | 4.75mm (takes panes up to 4.75mm) | Supplier drawing and data |
| Glass slot depth | 6mm | Supplier drawing |
| Panel slot width | 1.6mm (fits panels 0.8mm to 1.6mm) | Supplier drawing and data |
| Panel slot depth | 8mm | Supplier drawing |
| Glass-to-panel clearance | 7mm | Supplier data |
| Minimum bend radius | 58mm | Supplier datasheet |
| Material | Solid (non-cellular) EPDM rubber | Supplier datasheet |
| Colour | Black | Supplier data |
| Hardness | 65 to 75 IRHD | IRHD scale, supplier datasheet |
| Tensile strength | 10 MPa | Supplier datasheet (method not stated) |
| Elongation at break | 500% | Supplier datasheet (method not stated) |
| Tear strength | 50 kN/m | Supplier datasheet (method not stated) |
| Compression set | 21% | 22 hours at 70°C, supplier datasheet |
| Service temperature | -40°C to +90°C | Supplier data |
| Weight | 0.24kg per metre | Supplier data |
| Density | approx. 1.1 to 1.3 g/cm³ | Typical for solid EPDM, not tested on this profile |
| Dimensional tolerance | ISO 3302-1 class E2 | Typical for EPDM extrusions, not stated for this profile |
| Lengths | 10m to 29m in 1m steps; 30m full coil | One continuous piece per order line |
| Filler strip | Required, sold separately (large lock-strip size) | See "Complete your project" |
Materials and compliance
The seal is extruded from solid EPDM (ethylene propylene diene monomer), a synthetic rubber chosen for outdoor glazing because it shrugs off sunlight, ozone, rain and frost without cracking or going sticky. It stays flexible from -40°C to +90°C and holds its grip over time, shown by the 21% compression set after 22 hours at 70°C.
No food-contact, drinking-water, fire-performance or other regulatory approvals are stated for this profile, so we do not claim any. If your project needs a certified material, contact us before ordering.
Typical uses
- Fixed side and rear windows in horseboxes, livestock trailers, catering trailers and plant cabs
- Vision panels in sheet-steel machine guards, enclosures and kiosk doors
- Replacing perished lock-strip window rubbers on classic, commercial and leisure vehicles
- Acrylic or polycarbonate glazing in boat cabins, sheds and workshop doors where the skin is 0.8mm to 1.6mm

Which glazing seal do I need?
| Pane thickness | Panel thickness | Seal |
|---|---|---|
| Up to 4.75mm | 0.8mm to 1.6mm | This seal, 20mm x 17mm (7mm clearance, larger section) |
| Up to 4.75mm | 1.2mm to 1.6mm | Glazing weatherstrip seal 15mm x 13.5mm (slimmer profile) |
| 4.75mm | Up to 3mm | Weatherstrip glazing seal for 4.75mm glass and 3mm panels |
| 6mm | 6mm | Weatherstrip glazing seal 33mm x 23mm |
Measure the pane and the panel with a vernier caliper. A seal that is too loose will leak; one that is too tight will not accept the filler strip.
How much do I need?
Each option is one continuous length, so choose a length that goes all the way round the opening (or several openings) without a break. Measure the perimeter and add about 10% for corners and trimming. Example: a 900mm x 600mm cab window has a 3.0m perimeter, so 3.3m with allowance; three such windows need 9.9m, so order 10m. Buy the same total length of filler strip.
Fitting guide
- Clean and deburr the panel opening and the pane edge. Corner radii should be at least 58mm.
- Starting at the bottom centre, push the 8mm-deep panel slot onto the opening edge. Work round without stretching the rubber; ease it into the corners.
- Cut the end square and butt it tightly to the start so the joint sits at the bottom.
- Lubricate the glass slot lightly with soapy water and set the pane into it from the bottom, lifting the lip over the edge with a blunt plastic tool.
- Press the filler strip into the top groove with a glazing strip fitting tool. This spreads the lips and locks the pane and panel in place.
Complete your project
- Glazing strip fitting tool for rubber filler strips
- Large lock filler strip to suit this seal: ask us and we will supply the matching size by the metre
Frequently asked questions
Is the filler strip included?
No. The filler strip that locks the seal is sold separately. This 20 x 17mm seal takes the large lock-strip size, not the small 7 x 6mm strip used on slimmer seals. Contact us and we will match it for you.
What thickness of glass or plastic will it hold?
Panes up to 4.75mm thick: toughened or laminated glass, acrylic or polycarbonate. The glass slot is 6mm deep, so allow for 6mm of pane edge hidden inside the seal all round when sizing the pane.
What panel thickness does it fit?
Sheet panels from 0.8mm to 1.6mm. For panels up to 3mm use the 4.75mm glass to 3mm panel weatherstrip instead.
Can it go round corners?
Yes, if the corner radius is at least 58mm. Tighter corners make the rubber pucker and lift; use separate lengths joined at a mitre instead.
How do I cut and join it?
Cut square with a sharp knife or rubber cutter. Butt the two ends tightly at the bottom of the window; a dab of rubber-compatible cyanoacrylate adhesive on the joint faces gives a neater, sealed join.
Can it be used outdoors and in cold weather?
Yes. Solid EPDM resists UV, ozone and rain, and stays flexible from -40°C to +90°C.
Will it arrive in one piece?
Yes. Each order line is cut as one continuous length, 10m to 29m, or supplied as a 30m full coil.
Why is the 30m coil cheaper than 28m or 29m?
The 30m option is a full, uncut production coil, so it avoids cutting and re-coiling. If you need 28m or more, the full coil is the better buy.
Need help matching a glazing rubber? Contact our team with your pane and panel thickness, or call +44 1282 277786.
Product details
| SKU | IP-EPDM-20X17-10 |
|---|---|
| Weight | 5.29 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Glazing Weatherstrip Seal 20mm x 17mm – For 4.75mm Glass & 0.8–1.6mm Panel – 10m to 30m